Summary of QuadroE1/T1
Page 2
Quadroe1/t1 manual i: installation guide quadroe1/t1; (sw version 3.2.X) copyright and trademarks copyright © 2003 - 2006 epygi technologies, ltd. All rights reserved. Quadroe1/t1 is a registered trademark of epygi technologies, ltd.Microsoft, windows, and the windows logo are registered trademarks ...
Page 3
Quadroe1/t1 manual i: installation guide quadroe1/t1; (sw version 3.2.X) if your home has specially wired alarm equipment connected to the telephone line, ensure the installation of the quality ac surge suppressor in the ac outlet s t be e ered to: • al shock, do not open the quadroe1/t1. Refer serv...
Page 4
Quadroe1/t1 manual i: installation guide quadroe1/t1; (sw version 3.2.X) table of contents manual-i: installation guide about this installation guide ....................................................... 5 requirements ............................................................................ 6 ...
Page 5
Quadroe1/t1 manual i: installation guide about this installation guide quadroe1/t1; (sw version 3.2.X) 5 about this installation guide this installation guide explains the installation of the quadroe1/t1 voip gateway. It gives step-by-step instructions to provision the quadroe1/t1 and configure the ...
Page 6: Requirements
Quadroe1/t1 manual i: installation guide requirements quadroe1/t1; (sw version 3.2.X) 6 requirements • one 120/240 v power outlet in close proximity to the quadroe1/t1. • one rj-45 ethernet 10/100 broadband internet connection. • one off-the-shelf analog phone with an rj-11 telephone cable. • one ca...
Page 7: Hardware Overview
Quadroe1/t1 manual i: installation guide hardware overview quadroe1/t1; (sw version 3.2.X) 7 hardware overview quadroe1/t1’s rear panel fig. I-1: quadroe1/t1's backplate 1 power supply socket. Use only the power adapter delivered with the quadroe1/t1. 2 phone socket with a rj-11 connector enables co...
Page 8
Quadroe1/t1 manual i: installation guide hardware overview quadroe1/t1; (sw version 3.2.X) 8 quadroe1/t1’s front panel leds fig. I-2: quadroe1/t1's front panel leds 1 busy green (status of the cpu) on: device is booting off: no power blinking: activity 2 info yellow (system information) on: device i...
Page 9: Installing Quadroe1/t1
Quadroe1/t1 manual i: installation guide installing quadroe1/t1 quadroe1/t1; (sw version 3.2.X) 9 installing quadroe1/t1 networking overview to establish a connection between the pstn (or your pbx) and the internet, a voip gate- way is needed. The quadroe1/t1 is a voip gateway, and will perform the ...
Page 10
Quadroe1/t1 manual i: installation guide installing quadroe1/t1 quadroe1/t1; (sw version 3.2.X) 10 connecting the hardware fig. I-4: connecting the hardware • verify the product package contents are complete. Refer to the contents sheet included in the packaging to determine if all the items were sh...
Page 11: Configuring The Quadroe1/t1
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 11 configuring the quadroe1/t1 to configure the quadroe1/t1 basically, four steps are needed: step1: basic configuration using the system configuration wizard and the internet configuration wizard. ...
Page 12
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 12 logging in to quadroe1/t1 start a browser (ms internet explorer, netscape, opera) on a pc connected to the lan port. Enter http://172.30.0.1 (quadroe1/t1’s default lan ip address) into the addres...
Page 13
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 13 basic configuration two configuration wizards are available to accomplish the basic configuration of quadro devices: • the system configuration wizard - a tool for the administrator to define the...
Page 14
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 14 system configuration enter into the host name field a unique name for the quadroe1/t1. This is useful when many quadro’s are part of a network and one administrator has remote access to all of th...
Page 15
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 15 fig. I-9: dhcp settings for the lan interface page click on next to display the regional settings page . Regional settings fig. I-10: regional settings page proper configuration of regional setti...
Page 16
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 16 finishing the system configuration wizard fig. I-11: system configuration wizard finishing page click the finish button to complete the system configuration wizard. The quadro will then stop inte...
Page 17
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 17 fig. I-13: confirm settings page please note: you must confirm the settings within 20 minutes. If not, the device will revert back to the previous configuration and reboot. Please note : if you d...
Page 18
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 18 uplink configuration select here the wan interface protocol required by you isp: pppoe (point to point proto- col over ethernet), pptp (point to point tunneling protocol) or ethernet. Fig. I-15:u...
Page 19
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 19 fig. I-16: wan ip configuration page click the next button to display the wan interface configuration page. Ppp/pptp configuration enter the ip address of the pptp server into the pptp server tex...
Page 20
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 20 fig. I-17: ppp configuration page if your isp assigns a dynamic ip address, activate the dynamic ip address radio button, otherwise activate the fixed ip address radio button and enter the ip add...
Page 21
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 21 dns settings select fixed nameserver and enter its ip address. If you use your dhcp server and if it will deliver a dns server, you may select dynamically by provider. When using a static ip ad- ...
Page 22
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 22 please note: the settings should be confirmed within 20 minutes; otherwise, the device will revert back to the previous configuration and reboot. Please note : if you do not use dhcp for your lan...
Page 23
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 23 configuring the e1/t1 settings) of the quadroe1/t1 configuration and specify the e1it1 settings. Configuring the firewall the configuration of the firewall is only required if the quadro is manag...
Page 24
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 24 configuring the e1/t1 settings the quadroe1/t1 can be connected to a pbx or to the pstn via e1/t1 lines, using e1/t1 cas/ccs signaling. The quadroe1/t1 may be connected to act as a user (if conne...
Page 25
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 25 editing the e1/t1 trunk fig. I-23: trunk edit page select network as your interface type if your quadroe1/t1 is connected to a pbx, other- wise choose user. Next, you are required to enter the si...
Page 26
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 26 signaling type ccs fig. I-24: trunk t1 signaling type ccs page if you selected ccs as your signaling type, using the trunk link will take you to the page shown above. Here you can specify the sig...
Page 27
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 27 in the isdn l2 timers area the excessive ack. Delay t200 text field configures the period in milliseconds (digit values from 500 to 9999) between transmitted signaling packet and its acknowledgem...
Page 28
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 28 the value for switch type depends on the co when acting in the user mode and the pri- vate pbx capabilities when acting in the network mode. Attention: a timeslot can be used either for voice or ...
Page 29
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 29 fig. I-25: trunk t1 signaling type ccs - b-channels page channel selection drop down list is used to select between the preferred and exclusive b channel selection methods. For preferred channel ...
Page 30
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 30 edit will display the first page of the cas signaling wizard page (see below) where the sig- naling settings for the selected timeslots may be enabled or disabled and the force update timeslot se...
Page 31
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 31 signaling type cas fig. I-27: trunk t1 signaling type cas page if you selected cas as your signaling type on the trunk settings - edit entry page, you will get the page shown above using the trun...
Page 32
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 32 the signaling standard drop down list is available only in e1 mode and allows selecting the connection signaling standard (itu, itu_t_2 or melcas). In the table below, the page lists all timeslot...
Page 33
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 33 fig. I-29: cas signaling wizard - page 2 from this page, signaling type settings of the timeslot(s) might be configured: allowed call type is used to select the allowed call directions: incoming,...
Page 34
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 34 when alternative disconnection mode checkbox is selected, the quadro will play a busy tone towards the pbx/co if the call has been failed. After 60 second timeout, the quadro will disconnect the ...
Page 35
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 35 attention: when quadro acts in the network mode with the attendant as a destination to route the incoming calls, digit forwarding should be disabled on the pbx side. Otherwise, incoming digits ma...
Page 36
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 36 fig. I-32: cas signaling wizard - page 5 this page only appears when use default country settings checkbox is not selected on the previous page and is used to configure advanced country settings....
Page 37
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 37 incoming dnis size text field indicates the number of received digits (in a range from 0 to 255) required to establish a call. When the field has 0 value, the system uses either timeout defined i...
Page 38
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 38 fig. I-33: call routing example your pstn service provider supplies you with a set of pstn telephone numbers for your e1/t1 line. If you want to assign these numbers to the phones connected to th...
Page 39
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 39 to define the call routing paths needed on quadroe1/t1 open call routing in the teleph- ony menu and select local routing table. The call routing - local routing page will be displayed (it is a w...
Page 40
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 40 fig. I-36: local call routing wizard: routing call type add entry page 1 pattern requires the routing pattern. To make the specified call, the appropriate call code should be dialed prior to the ...
Page 41
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 41 description allows entry of short text, e.G. To name the path. Filter on caller/call type modify caller id allows you to limit the functionality of the cur- rent route to be used by the defined c...
Page 42
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 42 enable activity timeout checkbox is used to limit time-to-live period of routing pattern (makes sense if accept or failure feedback arrives too late from the destination). Checkbox selection enab...
Page 43
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 43 • enable privacy - with this selection, sip privacy will be specified for the corresponding route. This selection enables a group of checkboxes in order to choose the key headers that are to be f...
Page 44
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 44 quadroe1/t1 pattern nds prefix call type destination address description 8546033[0-2] sip 10.20.30.10 path to quadro2x 8546034[0-4] sip 10.20.30.20 path to quadro4x 85460350 pbx path to phone con...
Page 45
Quadroe1/t1 manual i: installation guide configuring the quadro e1/t1 quadroe1/t1; (sw version 3.2.X) 45 registering on epygi’s technical support it is recommended that you register your quadroe1/t1 on the epygi technical support web page. Registration will give you access to the technical support d...
Page 46: Appendix: Pc Dhcp Settings
Quadroe1/t1 manual i: installation guide appendix: pc dhcp settings quadroe1/t1; (sw version 3.2.X) 46 appendix: pc dhcp settings the quadroe1/t1 lan port has a dhcp server that provides dhcp ip addresses to de- vices connected to the lan either directly or through an ethernet hub or switch. Appendi...
Page 47
Quadroe1/t1 manual i: installation guide appendix: pc dhcp settings quadroe1/t1; (sw version 3.2.X) 47 4. Select obtain an ip address automatically, then click on advanced. . 5. You will see the entry dhcp enabled. 6. Click on ok three times to close all windows. Tcp/ip and dhcp under windows 95/98/...
Page 48
Quadroe1/t1 manual i: installation guide appendix: changing the admin password quadroe1/t1; (sw version 3.2.X) 48 appendix: changing the admin password for security reasons, it is recommended that you change the default admin password. The username of the administrator (admin) cannot be changed. To ...
Page 49
Quadroe1/t1 manual i: installation guide appendix: configuring sip nat traversal quadroe1/t1; (sw version 3.2.X) 49 appendix: configuring sip nat traversal the quadroe1/t1 initiates and receives sip calls from the network connected to the wan port). In order to receive sip calls, the quadroe1/t1 mus...
Page 50
Quadroe1/t1 manual i: installation guide appendix: configuring sip nat traversal quadroe1/t1; (sw version 3.2.X) 50 • for max mapped rtp/rtcp port 6059 • click the save button to save the contents. The quadroe1/t1 will activate the settings and register the extension on the epygi sip server after a ...
Page 51
Quadroe1/t1 manual i: installation guide appendix: checking the connections quadroe1/t1; (sw version 3.2.X) 51 appendix: checking the connections if the system seems to work incorrectly even when all cables are connected properly, it may be helpful to start network diagnostics: the wan link, ip conf...
Page 52
Quadroe1/t1 manual i: installation guide appendix: checking the connections quadroe1/t1; (sw version 3.2.X) 52 basic tests: checking for physical link: no wan link please check the physical connection of the wan interface. Cable not plugged or broken? Test failed. If you pass the diagnostics success...
Page 53
Quadroe1/t1 manual i: installation guide appendix: pin assignment of e1/t1 quadroe1/t1; (sw version 3.2.X) 53 appendix: pin assignment of e1/t1 pin signal 1 rxring 2 rxtip 3 n.C. 4 txring 5 txtip 6 n.C. 7 n.C. 8 n.C. Fig. I-44: pin assignment of e1/t1.
Page 54
Quadroe1/t1 manual i: installation guide appendix: pin assignment of e1/t1 quadroe1/t1; (sw version 3.2.X) 54 qig-quadro-02-30