Electric fireplace heater i n s t r u c t i o n m a n u a l m707p-2628fcn ndf-62n attention: 1. Find a location for the fireplace heater that is protected from direct sunlight. 2. Do not plug the unit into the power outlet before you read all instructions..
2 s a f e t y i n s t r u c t i o n s important please note when you open the carton carefully check the unit and make sure there are no damages. If you have any problems with the unit, with how the various functions work or with hidden damages or missing parts please call 1-800-459-4409 (est) immed...
3 heater where it may fall into a bathtub or other water container. 8) do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. 9) to disconnect fireplace, turn controls to off, then ...
4 at c is available for connecting three-blade grounding-type plugs to two-slot recep- tacles. The green grounding plug extend- ing from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is a...
5 a s s e m b ly i n s t r u c t i o n s parts list: fireplace insert 1 a) top panel 1 b) base 1 c) front panel 1 d) left front panel 1 e) right front panel 1 f) left side panel 1 g) right side panel 1 r) medium kd screws 2 s) short kd screws 3 t) mounting brackets 2 u) wood connectors 2 w) kd screw...
6 a s s e m b ly i n s t r u c t i o n s please do not fully tighten the kd screws until all panels are assembled. Note: each plastic connector is pre-assem- bled (pre-drilled) on the specific panels with 2 screws. If the kd screw(s) do not fit during assembly, loosen the 2 (pre-drilled) screws to a...
7 fig. D step 5: attach top panel [a] to the unit as shown in fig e, with 4 kd screws. See fig. E. Fig. E step 6: tighten all kd screws. Fireplace insert installation: the fireplace insert can be installed after the mantel has been fully assembled. Warning: make sure the fireplace insert controls ar...
8 the risk of the fireplace being tipped over accidentally. Warning: this cable may reduce possible risk of injury if the fireplace is improperly handled, but is not a substi- tute for proper adult supervision. Children should not be left unattended near any heater. 1. Drill a 5/16 in (8 mm) hole in...
9 o p e r a t i o n temperature control: to adjust the temperature to your individual require- ments, turn the temperature control dial to the right (clockwise) to increase the desired temperature and to the left for lower tem- perature. This temperature control dial can only be used while the o/i s...
10 touch up repair paint 1. Paint directly on the mantel unit if necessary. Fig. A. Fig. A repairs if any problems are found with the original parts during mantel assembly such as the panels cannot be installed with the plastic connector. Try to solve by one of the fol- lowing method. Tools required...
11 r e p a i r s e t / c l e a n i n g option 2: use the small l-brackets and screws. 1. Place the small l-bracket to the unit as shown and mark the drill-holes on the mantel as shown in fig. F. 2. Drill the holes with diameter 1/16 inch- es (2 mm) and depth 5/16 inches (8 mm) on the mantel. Each sm...
12 warranty every electric fireplace heater is tested be- fore it leaves the factory and it is guaranteed for one year. If the unit should fail to operate correctly within one year from the date of purchase, call customer service at 1-800- 459-4409 (est). We will, at our discretion ei- ther repair o...
