Quartech 9113-1 Series Product Manual

Manual is about: Ethernet Bridge II for Ultra 3000 Servo

Summary of 9113-1 Series

  • Page 1

    Product manual model 9113-1-x ethernet bridge ii for ultra 3000 servo quartech corporation 15923 angelo drive macomb township, michigan 48042-4050 phone: (586) 781-0373 fax: (586) 781-0378 www.Quartechcorp.Com pm9113-1-x revision 0 the product described in this document can have a variety of uses, t...

  • Page 2

    Model 9113-1-x product manual page 2 the model 9113 ethernet bridge allows an allen-bradley plc such as a micrologix or compactlogix to monitor and control an ultra 3000 servo drive over an ethernet connection. The 9113 connects to the ultra 3000 cn3 port using a cable provided with the unit and to ...

  • Page 3

    Model 9113-1-x product manual page 3 theory of operation the 9113 allows a plc to read and write parameters within the ultra 3000 drive using the message instruction. The parameters in the ultra 3000 are mapped to file/element numbers so the plc accesses the ultra parameters as though they were file...

  • Page 4

    Model 9113-1-x product manual page 4 multiple axis: the 9113 provides a bridge to a single drive when an application requires multiple drives to be controlled then each drive will have an associated 9113 with a unique ip address. An ethernet hub or switch will be required to connect the devices. Eac...

  • Page 5

    Model 9113-1-x product manual page 5 ethernet cables: the 9113 operates with standard ethernet cables available from many sources. The examples below are consistent with the tia/eia 568-b color code standard. Straight through cable crossover cable device to hub / switch device to device ethernet cab...

  • Page 6

    Model 9113-1-x product manual page 6 2180 cable - 9113 to ultra 3000 (supplied with 9113) 9 pin male d-type ultra 3000 communication parameters: 38400 baud, 8 data bits, no parity, one stop bit 2182 cable - 9113 to 9120 two port multiplexer 9 pin female d-type specifications: electrical: 24 vdc, ±5%...

  • Page 7

    Model 9113-1-x product manual page 7 9113 hardware power terminal: power to the 9113 is supplied through a three position removable compression terminal block. The 9113 requires 24 volt, two hundred milliamp direct current power. An earth ground connection is also required and provided through the t...

  • Page 8

    Model 9113-1-x product manual page 8 if switch four is off and switch two is on... This dhcp mode is used during initial setup, or when the ip address assigned to the 9113 is unknown, or when you attach it to a personal computer that is within a different subnet then the 9113. The ip address server ...

  • Page 9

    Model 9113-1-x product manual page 9 9113 power-up: power-up with dip switch 4 off... When power is applied to the 9113 it will begin looking for an active ethernet network. During this time the mode led and fault led will be lit steady red and remain that way until an active network is detected. On...

  • Page 10

    Model 9113-1-x product manual page 10 physical size and mounting: dimensions in inches the 9113 is enclosed in a rugged steel case and provides a din rail mounting clip that allows quick mounting and dismounting. To mount the 9113 tilt it forward and hook the clip to the top of the din rail. Rotate ...

  • Page 11

    Model 9113-1-x product manual page 11 ethernet gateway for ultraware: the 9113-1-1 allows allen-bradley ultraware software to access ultra 3000 drives over an ethernet network when used in conjunction with the quartech ethernet gateway program. The ethernet gateway program creates a virtual serial p...