Quickie Quickie User Instruction Manual & Warranty - page 17
I X . S e t - u p & A d j u s t m e n t
930575 Rev. A
32
930575 Rev. A
I X . S e t - u p & A d j u s t m e n t
33
R. QUICK-RELEASE CASTER STEMS (OPTIONAL)
1. Installation
a) Depress quick-release caster button (A).
b) Slide caster stem into caster stem sleeve (B).
2. Adjustment
a) To adjust the caster stem a 3/4" socket is need-
ed to turn the caster stem nut.
b) You will also need a 1/2" wrench to lodge the
ball bearings on the opposite end of the caster
stem to prevent the caster stem from rotating.
c) Turn the hex nut clockwise to tighten.
d) There should only be zero to ten thousandths of
an inch (.010”) of play.
e) Replace dust cover to caster housing.
S. ANTI-TIP TUBES - REAR AND FRONT
1. To Insert Anti-Tip Tubes into Receivers
a) Press the anti-tip release button (A) on the
anti-tip tube so that the release pin (B) is
drawn inside.
b) Insert the tube into the anti-tip receiver.
c) Turn the anti-tip tube until release pin is posi-
tively engaged in the receiver mounting hole
(C).
d) Insert second anti-tip tube the same way.
2. To Adjust Anti-Tip Height
a) Press the anti-tip wheel release button (A) so
the release pin is drawn inside.
b) Raise or lower to one of the three pre-drilled
holes.
c) Turn the anti-tip tube until release pin is posi-
tively engaged in the receiving hole (B).
d) Adjust the second anti-tip tube wheel the same
way. Both wheels should be exactly the same
height.
3. To Adjust the Rear Anti-Tip Bracket Height
a) Remove the two hex bolts (A).
b) Raise or lower as needed.
c) Replace and tighten bolts.
NOTE–
Rear anti-tip brackets are attached with axle
plate hardware (see Seat Height Adjustment
section below).
P. CASTER FORKS
1. Caster Fork Adjustment
a) Loosen the bolt (A) and remove the caster.
b) Either change caster size and/or position the
caster upward or downward in pre-drilled holes
(1" apart) on caster fork.
c) Replace bolt and tighten securely.
d) Repeat with other caster.
NOTE–
Two-hole caster forks allow interchanging 5", 6"
and 8" casters and adjusting seat height. These
changes may affect the floor to seat height.
Q. CASTER PLATES
1. Angle Adjustment
a) Loosen the bolts (A) that secure the caster
assembly until the eccentric washers are free to
rotate.
b) Place a large right triangle against a flat work
surface and the front surface of the caster bear-
ing housing. This will align the caster stem rota-
tional axis perpendicular to the work surface.
c) Align the eccentric washers and retighten the
bolts.
d) Repeat the process for the other caster.
2. Angle Adjustment: Caster Plates with Transit
Option
a) Loosen the bolts (A) that secure the caster
assembly.
b) Place a large right triangle against the flat sur-
face and the front surface of the caster bearing
housing. This will align the caster stem rota-
tional axis perpendicular to the flat surface.
c) Align the eccentric washers and retighten the
bolts.
d) Repeat the process for the other caster.
Anti-Tip Tube into Receiver
A
B
Quick-Release Caster Stem
A
B
Anti-Tip Height
A
B
C
Caster Fork
A
Caster Housing Assembly
A
Caster Assembly at 90º Alignment
Caster Housing Assembly with
Transit Option
A
Anti-tip Bracket
A