Summary of SWAN
Page 1
Tm english user manual g b g b swan © 2009 r82 a/s. All rights reserved. The r82 logo and the bathing chair swan are registered trademarks of r82 a/s. 07.2016 - rev.4.
Page 2
G b g b gb contents safety ................................................................................4 warranty ............................................................................4 washing .............................................................................4 tools ..............
Page 3
G b g b swan the swan is a classic commode from r82. The seat is made of fibre glass and the frame of powder coated and stainless steel respectively, which means the swan is also splendid as a bathing chair. The swan has been especially developed by r82 after many years of experience designing and m...
Page 4
G b g b safety the swan has earned the ce-mark. This certifies that it meets all relevant european safety requirements. The durability of this product is 5 years when it is used on a daily basis. Hereafter the product must be renovated (by r82 personnel) to extend the lifetime. Remove the ce-mark, w...
Page 5
G b g b gb size 2+3 size 4+5+6+7 preparing for use follow the instructions below to ready your swan for use: 1) remove the wrapping and wipe the chair with a cloth before use. 2) remove the wooden bar on the back of the frame, which protect the chair during trans- portation. Follow the instructions ...
Page 6: √
A a b c √ g b g b gb gb height adjustment 1) start by loosening all screws (a). Remove the screws. Left rear wheel and both front wheels are to be adjusted to the holes in the internal rod. 2) tighten the screws when the desired height is reached. 3) the right rear wheel is for adjustment and to avo...
Page 7
A b a b g b g b gb mounting wheels 1) remove the ferrules (a) 2) screw on the wheels (b) and tighten with a 13 mm spanner. For information on adjusting the height, see passage on ‘height adjustment’ gb disassembling the wheels follow the instructions below to disassemble the wheels on swan: 1) loose...
Page 8
A c a b b g b g b gb headrest 1) loosen the tightening handle (a) and place the headrest in the white fitting. Tighten the handle when the requested height is reached. 2) loosen the screw (b) to adjust the headrest from side to side. Push handle 1) loosen the tightening handle (a) and place the push...
Page 9
B a g b g b mounting the upholstery to mount the upholstery correctly, follow below instructions. Swan size 1+2+3: 1) place the upholstery in the chair and lead the velcro straps through the slots in the seat. 2) velcro the straps together behind the seat. (a) swan 4+5+6+7: 1) place the upholstery i...
Page 10
A b g b g b splash guard only for size 4+5+6+7 to mount the splash guard just push it down until it locks. To remove the splash guard pull out the front edge and lift. Mounting the pan the pan is mounted from the back of the chair. Gb gb footrest follow the instrucions below to mount the foot- rest ...
Page 11
A c b g b g b use this drawing together with the descriptions on the following pages. 11.
Page 12
A b c a b c a g b g b foot straps the foot straps can be opened and closed by using the velcro or the buckle (a). Follow the instructions below for mounting. * open the straps and pull them (a) through the slides in the foot plates. * close the straps around the users foot. Take care that all the fi...
Page 13
A b c g b g b hip belt the hip belt can be opened and closed by using the buckles. Follow the instructions below, with help from page 11. * lead the straps through the slots in the seat (c). * when the straps has been led through the slots, fit a buckle at the end. Take care that all the fixations a...
Page 14
A b a b xxxxxx dmr ver.: xxxx art. No.: xxxxxxx product: xxxxxxx - size x max load: xxx kg (xx)xxxxxxxxxxxxxx(xx)xxxxxx(xx)xxxxxx g b g b gb product identification a) serial number the label is placed on the pan holder. B) manufacturer the label is placed on the top bar on the back of the frame. 14.
Page 15
G b g b measurements size 2 size 3 size 4 size 5 size 6 size 7 mm (inch) mm (inch) mm (inch) mm (inch) mm (inch) mm (inch) seat width, back (a) 200 (7¾") 230 (9") 250 (9¾") 300 (11¾") 340 (13¾") 410 (16") seat widht, front (a1) 300 (11¾") 340 (13¼") 360 (14") 380 (14¾") 430 (16¾") 480 (18½") seat de...
Page 16
G b g b gb gb producer r82 a/s parallelvej 3 8751 gedved denmark distributor gb please find your distributor on www.R82.Com technical data seat: glass fibre frame: stainless steel/powdercoated 16.