1. DL manuals
  2. Radiance
  3. Stove
  4. TAR-10
  5. Owner & Operator Instruction Manual

Radiance TAR-10 Owner & Operator Instruction Manual

Other manuals for TAR-10: Owner & Operator Instruction Manual

Summary of TAR-10

  • Page 1

    Owner & operator instruction manual for service contact: german knife inc. 1-800-500-3519 www.Turboairinc.Com model no. Www.Turboairinc.Com important safety notice this manual has been prepared for personnel qualified to install gas equipment, who should perform the initial field start-up and adjust...

  • Page 2

    2 table of contents installation & operation instruction general / rating plate clearance / caution / high shelf assembly leveling / air supply & ventilation convection oven- electrical connection gas connection / manual shut-off valve pressure regulator rogid connections flexible couplings initial ...

  • Page 3

    3 installation & operation instruction general (1) a manual gas shut-off valve must be installed in the gas supply (service) line ahead of the appliance and gas pressure regulator in the gas stream for safety and ease of future service. (2) the gas pressure regulator supplied must be installed on th...

  • Page 4

    4 installation & operation instruction clearance combustible construction back sides floor 8” 12” non-combustible 0 0 6” non-combustible construction the appliance area must be kept free and clear of all combustible. This unit is design-certified for the following installation only: the clearances f...

  • Page 5

    5 installation & operation instruction leveling (ranges equipped with ovens) a carpenter's spirit level should be placed on the oven's center baking rack and/or across the range top and the unit leveled both front to-back and side-to-side. If it is not level, cakes, casseroles, and any other liquid ...

  • Page 6

    6 installation & operation instruction gas connection note : the gas supply(service) line must be the same size or greater than the inlet line of the appliance. Radiance ranges and ovens use a 3/4" npt inlet. Sealant on all pipe joint must be resistive to lp gas. Manual shut-off valve this installer...

  • Page 7

    7 installation & operation instruction rogid connections double-check any installer-supplied intake pipes visually and/or blow them out with compressed air to clear any dirt particles, threading chips , or other foreign matter before installing a service line. Those particles will clog orifices when...

  • Page 8

    8 initial pilot lighting a. Top burners / raised griddle-broiler all radiance appliances are adjusted and tested before leaving the factory, effectively matching them to sea level conditions. Adjustments and calibrations to assure proper operation may be necessary on installation to meet local condi...

  • Page 9

    9 initial pilot lighting d. Standard oven pilot gas is tapped from the main burner manifold pipe, routed through tubing to a pilot safety valve, and then to the pilot burner. Gas flow is controlled by the safety valve. Oven pilot lighting or relighting is to be completed in the following sequence: (...

  • Page 10

    10 final preparation to check for leaks (1) remove the kick plate (see#2 above.) (2) check pilot tubing and burner tubing for leaks where they enter the gas valve with a soapy water solution. (3) light the pilot as described above. (4) check the connection of the pilot tubing leaving the gas valve w...

  • Page 11

    11 cleaning and maintenance any piece of equipment works better lasts longer when maintained properly. Cooking equipment is no exception. Your radiance range and must oven must be kept clean during the working day and thoroughly cleaned at the end of the day. Open burners daily 1. Lift all the open ...

  • Page 12

    12 cleaning and maintenance periodic cleaning cheek the ventilation system periodically to see that nothing has fallen down into the stub back, high riser or high shelf exhaust vents. Lubricate the pivot pins of oven door hinge where the right and left lever atms connect to the door. Use a multi-pur...

  • Page 13: Limited Warranty

    Limited warranty warranty claims... All claims for parts or labor must be made directly through german knife or radiance. All claims should include the model number, serial number, proof of purchase, date of installation and all pertinent information supporting the alleged defect. All warranty claim...