1. DL manuals
  2. RadioLink
  3. Remote Control
  4. RC4GS
  5. Instruction Manual

RadioLink RC4GS Instruction Manual

Manual is about: Digital 4 Channels Proportional RC System

Summary of RC4GS

  • Page 1

    Rc4gs digital 4 channels proportional rc system instruction manual ce fcc rohs.

  • Page 2

    1 introduction thank you for choosing radiolink 2.4 ghz 4ch pistol grip radio -- rc4gs. Rc4gs is default 4 channels transmitter and comes with receiver r6fg with gyro integrated and hv supported servo. Rc4gs, working with fhss spread spectrum and 67 channels pseudo frequency sequence hopping, both t...

  • Page 3

    2 important safety notice： the following two symbols will appear in this manual（please pay attention to the paragraph with this two symbols labeled）： prohibition testing and confirmation do not use in bad weather such as rainy or thundering to ensure the safety of you and others. Forbid to use this ...

  • Page 4

    3 contents 1. Introduction and service .......................................................................................................................... 1 2. Safety notice and warning ..............................................................................................................

  • Page 5

    4 3. Pistol grip control system rc4gs, transmitter with chip stm32f103rb, receiver r6fg/r6f with 32 bits industrial chip, 12ms only from transmitter to the receiver, thus provide control synchronous and performance perfect. The same fhss spread spectrum and 67 channels pseudo random frequency sequen...

  • Page 6

    5 size: 213 *117 * 115.5mm frequency: 2.4ghz ism band（2400mhz-2483.5mhz） channel: 4ch channel resolution: 4096, the regular jitter is 0.5us model: cars/boats modulation mode: gfsk spread spectrum: fhss, 67 channels pseudo random frequency sequence hopping 10 modes memory storage antenna length: 106m...

  • Page 7

    6 specification (1) frequency: 2.4ghz ism band (2400mhz~2483.5mhz) (2) size: 35*20*13mm (3) channel: 6 (4) model: cars/boats (5) modulation mode: gfsk (6) spread spectrum: fhss (7) 10 modes memory storage (8) antenna length: 200mm (9) control distance: more than 400 meters (10) lcd screen: 128*64 re...

  • Page 8

    7 r6fg with two indicate leds, while green led is on, it indicates normal working mode. While both green and red leds are on, it indicates gyro function working mode. 3.2.2 working mode r6fg has two working modes: normal working mode and gyro function working mode. Normal working mode green led, gyr...

  • Page 9

    8 when the gyro is enabled, pull the throttle trigger and then release (make sure the car stops running), turn the car right or left without changing steering wheel, if the servo will not follow with, it shows gyro is set backward. Press the binding switch one time for less than 1 second, the led fl...

  • Page 10

    9 4. Rc4gs functions 4.1 display when power switch turned on lcd screen when you power on the transmitter, lcd screen shows model name, transmitter name, battery voltage, steering trim, throttle trim. Model name the system can store the data for 10 models, model name will show on the lcd when you po...

  • Page 11

    10 both english and chinese version menu are available for which is convenient for chinese and english-speaking players to personalize function menus. (1) (1) access the function menu (by pressing “ exit ” and “enter”buttons simultaneously and holding them down for one second), the language select f...

  • Page 12

    11 4c-dwn: 4th channel (down) throttle epa th-fwd:0%~120% th-brk:0%~120% initial value: 100% aux servo epa 4c- up:0%~120% 4c-dwn:0% ~120% initial value: 100% steering epa st-lft:0%~120% st- rgt:0%~120% initial value: 100% aux servo epa 3c- lft:0%~120% 3c-rgt:0%~120% initial value: 100% end point adj...

  • Page 13

    12 steering operation curve adjustment (1) access the function menu (by pressing “exit” and “enter ”buttons simultaneously and holding them down for one second), press “inc(+)” button three times to chose eap function. (2) press “enter” button to get into stexp function interface, press “enter”key a...

  • Page 14

    13 the curve can be divided into: five dots throttle curve adjustment, single point adjustment, exponential curve adjustment, and braking index curve adjustment. To elevation point, we can select(exponential curve/single point curve/five points curve). Curve point adjustment (select five points 1-5)...

  • Page 15

    14 rate: -100 ~ 0 ~ +100 1. Enter the function menu and use “dec(-)” or “inc(+)” button to access thexp function, then select the “fwd-exp” function. 2. Press “dec(-)” or “inc(+)” button to select rate for adjustment, set the most comfortable value you want. From the graph you will clearly see the c...

  • Page 16

    15 mode: speed type selection all: speed adjustment adjustment range 0~100 (each direction) at 100, there is no delay (1) enter the function menu and use “dec(-)”or“inc(+) ” button to access thspd function. (2) press “enter” button to get into thspd function interface. (3) if initial mode setup item...

  • Page 17

    16 (4) press “enter” key to confirm "low" or "high" or “tgp1” setup item, and the value of your selected setup item will blink. Use “dec(-)” or “inc(+)” button to adjust the value. (note: in the interface of adjusting the value, return to the initial value (the initial value of low and high is “100”...

  • Page 18

    17 operation. -dty (cycle duty ratio): sets the proportion of the time the brakes are applied and the time the brakes are released by pulse operation. The ratio can be set to +3 ~ 0~-3 in 7steps. -stm (steering mixing): sets abs operation on/off according to the steering operation range. A.B.S funct...

  • Page 19

    18 select setting item "cyc" by pressing “dec(-)” or “inc(+)” button, then press “enter” key and the initial value of“cyc”will blink. Use“dec(-)”or“inc(+)”button to adjust the pulse speed (cycle). (note: in the interface of adjusting the value, return to the initial value "5" by pressing “dec(-)” an...

  • Page 20

    19 initial value of “stm”will blink. Use “dec(-)”or “inc(+)”button to adjust the steering mixing range. (note: in the interface of adjusting the value, return to the initial value "off" by pressing “dec(-)” and “inc(+)” buttons simultaneously for about 1 second.) press“enter”button, the adjusted val...

  • Page 21

    20 "0%": no acceleration "100%": maximum acceleration (approximately1/2of the forward side steering angle) forward acceleration amount (fwrd) 0%~100% initial value: 0% (2) brake side acceleration amount adjustment press “dec(-)” or “inc(+)” button to select “ brak ”, press“enter”key to confirm and t...

  • Page 22

    21 4.12 sub-trim "subtr" servo center position adjustment use this function to adjust the neutral position of the steering, throttle and channel 3 servos. Channel st: steering th: throttle ch3: channel3 ch4: channel4 sub-trim st: -100~0~+100 th: -100~0~+100 ch3: -100~0~+100 ch4: -100~0~ +100 initial...

  • Page 23

    22 (2) press “enter” button to get into rev function interface. (3) use “dec(-)” or “inc(+)” button to select st channel, press “enter”key, and the “nor” will blink. (4) press “enter” key, the “nor” stops blinking, use “dec(-)”or“inc(+)”button to reverse the st servo operation direction. (5) th chan...

  • Page 24

    23 setup item rate: brake amount brake amount (rate) 0%~100% initial value: 100% (1) enter the function menu and use “dec(-)” or “inc(+)”button to access atl function. (2) press “enter” button to get into atl function interface. (3) press “enter” key, and the initial value of rate will blink. Use “d...

  • Page 25

    24 channel selection (slv) st, th, ch3, ch4 initial value: st select setup item "slv" by pressing “dec(-)” or “inc(+)” button, press “enter” button, the initial slave channel will blink. Use“dec(-)” or “inc(+” ) button to select the slave channel you wish to adjust, press “enter” button, the blinkin...

  • Page 26

    25 4.17 channel 3 position "aux" the channel 3 and channel 4 servo position can be set from the transmitter. When ch3 is assigned to the 3 rd channel key, this setting is linked to the key. When ch3 and ch4 is not assigned to the 3rd channel key, it can be set with this screen. You can also set the ...

  • Page 27

    26 the transmitter’s low voltage alarm adjustable, it depends on what kind of battery, the 4.6v is may cause the battery over discharge and damage the battery. So you can set transmitter’s warning voltage when you use different battery. There are four options you can choose: li2s-7.2v li3-10.8v ni4s...

  • Page 28

    27 ch4: -100~+100 initial value: 0 (1) enter the menu, use “dec (-)” and “inc (+)” to select options to set. (2) press the button key “enter” to enter menu. (3) use “dec (-)” and “inc (+)” to select servo, then press “enter”. Now the initial value of servo will start flashing, use handle to change t...