Radionics D279A Operation And Installation Manual - D279A

D279A Operation & Installation Manual

Copyright © 2000 Radionics

Page 15

46456B

D279A

Programming

5.3

Programming the D7112 Panel Point

The D279A controls arming/disarming and entry/exit delay for the point to which it is connected.

5.3.1

Supervised Independent Zone Controls (Opening and Closing Reports)

To supervise the IZC, set the point code to 70000. To enable opening and closing reports from the zone controlled

by the D279A, cut the jumper labeled W1 OPEN/CLOSE (a violet colored jumper, see Figure 2) located on the

D279A. The D279A sounds audible alarms when the 70000 point code is used.

5.4

Programming the D6112 and D4112 Panel Protective Zone

The D279A controls arming/disarming and entry/exit delay for the zone input to which it is connected. The D279A

cannot be used to generate opening and closing reports, or silence the bell (through the software) with a D4112 or

D6112. See the 

D4112 Installation and Programming Manual

 (73-05365-002) or 

6112:MAIN Program Entry Guide

(74-04367-000) for complete zone code programming details.

W1 jumper:  For normal operation with the D4112 or D6112, do NOT cut jumper W1. However, if you want to display

the D279A armed or disarmed status at the D4112 or D6112 command center, or if you want to put the D279A on a

priority zone, cut jumper W1.

Some standard sub-control zone codes are shown below:

01150

24 hour zone, trouble on open, instant alarm on short, steady bell on alarm, restoral reports

04110

24 hour zone, instant alarm on short, no trouble conditions, steady bell on alarm

04100

24 hour zone, instant alarm on short, no trouble conditions, steady bell on alarm, local zone

04150

24 hour zone, instant alarm on short, no trouble conditions, steady bell on alarm, restoral reports

Using the 01- - -  zone code:  The 01- - - code only supervises the protective zone wire between the D279A and the

D4112/D6112. It is recommended that you DO NOT cut jumper W1 when using this code. If you cut the jumper, the

D279A sends a trouble report when disarming, and a restoral report when arming.

5.4.1

Audible Alarms

The D4112 and D6112 can be programmed to sound an audible alarm when the D279A is tripped while armed.

The D4112 or D6112 must be programmed with a bell time and the zone code must be programmed for audible

alarms.

5.5

Programming the D9112 for the D279A

The D279A can be used in one of two ways with the D9112: The D279A controls arming/disarming and entry/exit

delay for the point input it's connected to. If the W1 jumper is cut, point opening and closing reports may also be

sent. In this configuration, however, bell control from the D279A is not available. If the D279A is tripped into an alarm

condition and is programmed to sound the bell, you must silence the alarm bell using the command center it's

assigned to. You can also use the D279's on-board Form C relay to provide a bell output and thus allow bell control

from the D279A. You may use Point Index #31 from the default Program Record Sheet for the D279A for this

application.

The D279A can also be used to arm and disarm individual areas. When using it in this configuration, the D279A

should be the only point in the area. The scope of the command center should be programmed to include the

D279A's area (either Account Wide or Panel Wide scope). Cut the W1 jumper on the D279A to send area opening

and closing reports 

and  

to provide bell control from the D279A. Assign a passcode to the D279A's area with an

authority level for which no functions are enabled; this allows you to silence the bell only in the area in which the

passcode is assigned. You may use Point Index #28 from the default Program Record Sheet, with one modification:

Program  the point response 2 instead of 1.

5.6

Programming the 9000 Series Panels

The D279A can also be used in two ways on any D9412/G, D9112, D7412/G or D7212 panels. To use the D279A

as an individual protected area, connect the D279A to a 

single

 point on the 9000 Series control panel. Use the

burglary (green) output to activate the point on the 9000 Series control panel. The D279A is Open when disarmed

and Normal when armed. (No EOL resistor is needed.) The D279A can also arm and disarm an entire area. In this

application, the point connected to the burglary (green) output should be the only point assigned to the area. The

status of the area can be viewed from any keypad with panel wide scope. See the 

9000 Series Program Entry

Guide

 (74-07695-000) for the 9000 Series control panel for more information.