RADVision SCOPIA XT4200 Quick Setup Manual
© 2012 RADVISION Ltd. All intellectual property rights in this publication are owned by RADVISION Ltd. and are protected by United States copyright laws, other applicable copyright laws and international treaty provisions. RADVISION Ltd. retains all rights not expressly granted.
This publication is RADVISION confidential. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by RADVISION Ltd. No representation of warranties for fitness for any purpose other than what
is specifically mentioned in this guide is made either by RADVISION Ltd. or its agents. RADVISION Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. RADVISION Ltd. may make improvements or
changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to
locate a copy, please contact RADVISION Ltd. and a copy will be provided to you. Unless otherwise indicated, RADVISION registered trademarks are registered in the United States and other territories. All registered trademarks recognized. All right reserved.
For further information contact RADVISION or your local distributor or reseller. http://www.radvision.com
System Installation and Activation
Connect all cables to the SCOPIA XT4000 series Codec Unit (see overleaf). Power supply must be connected after all other connections have been established.
1.
Turn on the TV monitors. Monitor on HDMI1 is mandatory, monitor HDMI2 is optional.
2.
Make sure the remote control has batteries installed.
3.
Verify that the LED on the front panel of the Codec Unit is turned on.
4.
If the codec unit does not turn on automatically, press the
5.
button on the remote control.
The graphical menu appears on the monitors.
6.
A
Moving the Camera
On the general screen,
1.
navigate to Control Camera
using the arrow keys and
press OK.
Use the arrow keys to move
2.
the camera to the preferred
position.
Press Back when done.
3.
G
CAUTION:
Make sure all units are
switched off whenever connecting
or disconnecting devices.
Network Settings
Enter your network settings.
1.
For questions about this
information, consult your system
administrator.
Then select Next.
2.
Gatekeeper Settings
Enter your Gatekeeper settings
1.
and your E.164 number.
For questions about this
information, consult your system
administrator.
Then select Done.
2.
E
F
Country and Language of
Interface
System Name field displays the
1.
name of this Codec Unit as
displayed in a video conference,
for example:
Hong Kong,
•
or
9th Floor Conf Rm
•
Use the remote control keypad
2.
to type the name. Press OK to
toggle letters or numbers and
lower/upper case.
Select the Country and preferred
3.
Language.
Then select Next.
4.
C
Product Registration
Open the envelope that came with the XT4200.
1.
Locate the serial number and product key.
2.
On a computer, open a browser and navigate to
3.
http://licensing.radvision.com.
Complete the online registration form and enter the serial number and product
4.
key. The web registration form returns a license key.
Write down the license key and keep it in a safe place for future use.
5.
B
Graphics and Image Setup
If all the sides of the triangles 1 and
2 are visible on your monitor, select
next.
Otherwise, press 1 to adjust the
1.
position of the top left corner.
Use the arrow keys to move
2.
the selected triangle until it is
fully visible on your monitor.
Press OK when done.
Press 2 to adjust the position of
3.
the bottom right corner.
Repeat the procedure using the
4.
arrows.
Press OK and Next when done.
5.
D
SCOPIA XT4200 Quick Setup Guide
Package Content:
SCOPIA XT4000 series Codec Unit
•
SCOPIA XT XT4200 Camera
•
SCOPIA XT 1-way Microphone POD
•
SCOPIA XT Remote Control Unit
•
Base Camera kit: 2.5m triple camera cable,
•
including power, VISCA and DVI-D/HDMI
DVI-I to VGA converter
•
Cable LAN 4mt
•
Cable HDMI M/M, 2.5M
•
Power Supply and power cable
•
1-way Microphone POD cable
•
Remote Control Batteries
•
PN 62111-00011 r
ev A01
XT4200
XT4200