Operation manual notice d’emploi bedienungsanleitung p-6534-076 qxpdqxdoc 7/04 © 2004 by c.E. Studio-2 s.L. - spain (eec) http://www.Ramaudio.Com e-mail: support@ramaudio.Com professional power amplifiers dqx series 2.4 / 4.0 / 5.5 / 7.0
Warning: the exclamation point inside an equilateral triangle indicates the existen- ce of internal components whose substi- tution may affect safety. The lightning and arrowhead symbol warns about the presence of uninsula- ted dangerous voltage. To avoid fire or electrocution risk do not expose the...
0 safety precautions 1 general information 1.1 introduction 1.2 main characteristics 2 controls: where and what? 2.1 front panel 2.2 rear panel 3 installation and operation 3.1 connections 3.1.1 dual mode (stereo) 3.1.2 parallel mode 3.1.3 bridge mode (mono) 3.2 troubleshooting 4 technical specifica...
The ram ® dqx series power amps have been developped to meet the hig- hest goals in the field of professional power amplification. Their power, distor- tion and dynamics figures place them as reference in the industry. The dqx series incorporate unique absolute protection systems as the cro ™ , an i...
Lokalisierung der funktionen see figure signal attenuation level control knobs: permit independent control of each channel’s attenuation (41 steps). Ok/fault: this led light up red, shows the circuit relay on the output has open obeying one or several protections’ orders from the ampli- fier: short ...
See figure signal input: twin female neutrik ® xlr connectors for the amplifier’s signal input. Signal link: twin male neutrik ® xlr connectors for daisy chaining input signal to other amplifiers (parallel connected to female input connectors). Gain selection switch: gain selection switch: three pos...
The power switch must always be on the “off” position before plugging the amp to a properly earthed mains soc- ket (220-240v ac / 110v-120v ac). The input signal fed to the amplifier can be either balanced or un-balanced. The drawing below describes both ways to wire an xlr connector for the purpose...
Installation and operation installation et mise en service the amplifier can operate on three diffe- rent configurations: dual, bridge or parallel. The connections for the three modes are different. See figure - switch “off” the amp. - set the mode switch on the rear panel to “dual”. - select the ch...
3 4 dual channel 8 5 parallel inputs single channel.
In the event of incorrect connection or misfunctioning, the amp will activate one or more of its led to warn about the problem. Correct function: ok/prot lights green. Icl: the intelligent clip limiter is ope- rating (see page 10). No signal: (ok/prot lights green) no input signal is reaching the am...
(see fig ) the ram audio icl is an anticlip system that differentiates from conventional clip reduction systems in its dynamic tracking of the power supply rail values, to provide instant current/voltage demand and the- reby eliminating any limiting of the signal dynamics. More like a valve amplifie...
11 at the onset of current limiting, the scp circuit activates, opening the output relay which disconnects the excessive load. Every few seconds, the scp closes the relay momentarily, to monitor the short cir- cuit,re-opening instantly if the condition persists. This cycle repeats until the load ret...
12 8 6 7.
4.2 data 4.2 données techniques 4.2 technische daten technical specifications spécifications tecnische spezifikationen 13 technical specifications dqx-2.4 dqx-4.0 dqx-5.5 dqx-7.0 output power continuous average power rms, 1khz, 1.0% thd+n @ 2 Ω 2x 1200 w 2x 1950 w 2x 2700 w 2x 3450 w @ 4 Ω 2x 800 w ...
Manufactured in the eec by c.E. Studio-2 s.L. Pol. Ind. La lloma - c/sierra perenxisa nº28 46960 aldaya - valencia - spain phone: +34 96 127 30 54 fax: +34 96 127 30 56 http://www.Ramaudio.Com e-mail: support@ramaudio.Com.
