1. DL manuals
  2. RAM
  3. Automobile
  4. 2015 1500
  5. Owner's Manual

RAM 2015 1500 Owner's Manual

Other manuals for 2015 1500: User Manual, Operating Information Manual
Manual is about: RAM TRACK

Summary of 2015 1500

  • Page 1

    1 5 0 0 / 2 5 0 0 / 3 5 0 0 chrysler group llc o w n e r ’ s m a n u a l 2 0 1 5 20 15 r am t ru ck 15 00 /2 50 0/ 35 00 15d241-126-aa first edition printed in u.S.A. R a m t r u c k.

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents ! Introduction . . . . . . . . . . . . . . . . . . . . . . . .4 ! How to use this manual . . . . . . . . . . . . . .4 ! Warnings and cautions . . . . . . . . . . . . . .6 ! Van conversions/campers . . . . . . . . . . . .6 ! Vehicle identification number . . . . . . . .6 ! Vehic...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 9

    Frame and underbody as well as the automobile infor- mation disclosure label affixed to a window on your vehicle, the vehicle registration and title. Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seri...

  • Page 11: Contents

    Things to know before starting your vehicle contents ! A word about your keys . . . . . . . . . . . . .12 ▫ ignition node module (ignm) . . . . . . . . . . . .12 ▫ keyless ignition node (kin) — if equipped . . .13 ▫ key fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ removing key f...

  • Page 12

    ▫ using the panic alarm . . . . . . . . . . . . . . . . . .28 ▫ rke air suspension (remote lowering of the vehicle) — if equipped . . . . . . . . . . . . . . .29 ▫ programming additional transmitters. . . . . . . .30 ▫ transmitter battery replacement . . . . . . . . . . .30 ▫ general information . ....

  • Page 13

    ▫ exhaust gas . . . . . . . . . . . . . . . . . . . . . . . . .115 ▫ safety checks you should make inside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 ▫ periodic safety checks you should make outside the vehicle . . . . . . . . . . . . . . . . . . . . . . . . .118 2 thing...

  • Page 14

    A word about your keys your vehicle uses either a key start ignition system or keyless ignition system. The key start ignition system consists of a either a bladed key with an immobilizer chip in it, or a key fob with remote keyless entry (rke) transmitter and an ignition node module (ignm). The key...

  • Page 15

    Keyless ignition node (kin) — if equipped this feature allows the driver to operate the ignition switch with the push of a button, as long as the remote keyless entry (rke) transmitter is in the passenger compartment. The keyless ignition node (kin) has four operating positions, three of which are l...

  • Page 16

    Key fob key fob — if equipped the key fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired posi- tion. It also contains the remote keyless entry (rke) transmitter and an emergency key, which stores i...

  • Page 17

    Kin key fob — if equipped this kin key fob allows the driver to operate the ignition switch with the push of a button, as long as the remote keyless entry (rke) transmitter is in the passen- ger compartment. The keyless ignition node (kin) has four operating positions, three of which are labeled and...

  • Page 18

    Removing key fob from ignition place the shift lever in park (if equipped with an automatic transmission). Turn the key fob to the off position and then remove the key fob. Note: • the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for up to 10 minute...

  • Page 19

    Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park, and push ignition button to place ignition in off mode. When leaving the vehicle, always lock your ve- hicle. • never leave children alone in a vehicle, or with access to an unlocked vehicle. • all...

  • Page 20

    Key-in-ignition reminder opening the driver’s door when the key fob is in the ignition and the ignition switch position is off or acc, a chime will sound to remind you to remove the key fob. Note: • #keyed# ignition systems will chime in off or acc when the driver door is open. • “keyless# ignition ...

  • Page 21

    During normal operation, after turning on the ignition switch, the vehicle security light will turn on for three seconds for a bulb check. If the light remains on after the bulb check, it indicates that there is a problem with the electronics. In addition, if the light begins to flash after the bulb...

  • Page 22

    Caution! • always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended. • for vehicles equipped with keyless enter-n-go™, always remember to place the ignition in the off position. At the time of purchase, the original owner is provided with a four-digit person...

  • Page 23

    Vehicle security alarm the vehicle security alarm monitors the vehicle doors and ignition for unauthorized operation. When the ve- hicle security alarm is activated, interior switches for door locks are disabled. The system provides both au- dible and visible signals for the first three minutes the ...

  • Page 24

    Same exterior zone (refer to #keyless enter- n-go™# in #things to know before starting your vehicle# for further information). • press the lock button on the remote keyless entry (rke) transmitter. 3. If any doors are open, close them. The vehicle security alarm will set when you use the power door ...

  • Page 25

    5. For vehicles not equipped with keyless enter-n-go™, insert a valid key into the ignition switch and turn the key to the on position. The vehicle security alarm is designed to protect your vehicle; however, you can create conditions where the system will give you a false alarm. If one of the previ...

  • Page 26

    Note: • the front courtesy overhead console and door cour- tesy lights will not turn off if the dimmer control is in the “dome on” position (rotate horizontal thumb wheel on the bottom of the switch to the far right detent position). • the illuminated entry system will not operate if the dimmer cont...

  • Page 27

    Key fob with remote keyless entry (rke) transmitter (ignm) key fob with rke transmitter keyless enter-n-go™ fob (kin) 2 things to know before starting your vehicle 25.

  • Page 28

    Remote unlock the doors push and release the unlock button on the rke transmitter once to unlock the driver’s door. Push the unlock button twice within five seconds to unlock all doors, the tailgate and the rambox® (if equipped). The turn signal lights will flash to acknowledge the unlock signal. Th...

  • Page 29

    Flash lamps with remote key lock this feature will cause the turn signal lights to flash when the doors are locked or unlocked with the rke transmit- ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: • for vehicles not equipped with a touchscreen ra...

  • Page 30

    • for vehicles equipped with a touchscreen radio, refer to “uconnect® settings” in “understanding your in- strument panel” for further information. Note: pushing the lock button on the rke transmitter while you are in the vehicle will activate the vehicle security alarm system. Opening a door with t...

  • Page 31

    Rke air suspension (remote lowering of the vehicle) — if equipped for easy entry and loading, your vehicle can be lowered by pushing the key fob air suspension lowering button two times. When remote key fob lowering is requested, the vehicle will send a series of chirps and flashes to alert the cust...

  • Page 32

    Programming additional transmitters if you do not have a programmed rke transmitter, contact your authorized dealer for details. Transmitter battery replacement the recommended replacement battery is one cr2032 battery. Note: • perchlorate material — special handling may apply. See www.Dtsc.Ca.Gov/h...

  • Page 33

    2. Separating rke halves requires screw removal – if equipped, and gently prying the two halves of the rke transmitter apart. Make sure not to damage the seal during removal. Keyless ignition node (kin) emergency key removal remove screw from transmitter case 2 things to know before starting your ve...

  • Page 34

    3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar, then replace the battery. When replacing the battery, match the + sign on the battery to the + sign on the inside of the battery separating ignition no...

  • Page 35

    Clip, located on the back cover. Avoid touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 4. To assemble the rke transmitter case, snap the two halves together, reposition and secure the screw as shown in step...

  • Page 36

    Remote starting system — if equipped this system uses the remote keyless entry (rke) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security. The system has a range of approximately 300 ft (91 m). Note: • the vehicle must be equipped with an automatic...

  • Page 37

    Warning! • do not start or run an engine in a closed garage or confined area. Exhaust gas contains carbon mon- oxide (co) which is odorless and colorless. Carbon monoxide is poisonous and can cause serious in- jury or death when inhaled. • keep remote keyless entry (rke) transmitters away from child...

  • Page 38

    • if an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds. • the park lamps will turn on and remain on during remote start mode. • for security, power window and power sunroof op- eration (if equipped) are disabled when the vehicle is in the remote...

  • Page 39

    Remote start comfort systems — if equipped when remote start is activated, the heated steering wheel and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature will automatically turn on when the remote start is activated. These featur...

  • Page 40

    Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will unlock the driver door lock on your vehicle. Warning! • do not leave children or animals inside parked vehicles in hot weather. Inte...

  • Page 41

    Warning! (continued) • do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with keyless enter-n-go™ in the acc or on/run mode. A child could operate power windows, other controls, or move the vehicle. Power doo...

  • Page 42

    Operate. A chime will sound if the key fob is in the ignition switch and a door is open, as a reminder to remove the key fob. Automatic door locks — if equipped the auto door lock feature default condition is enabled. When enabled, the door locks will lock automatically when the vehicle’s speed exce...

  • Page 43

    Child-protection door lock to provide a safer environment for children riding in the rear seat, the rear doors (if equipped) of your vehicle have the child-protection door lock system. To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to enga...

  • Page 44

    Warning! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child-protection locks are engaged. Note: • after setting the child-protection door lock system, always test the door from the inside to make certain it is in the des...

  • Page 45

    • if the vehicle is unlocked by the passive entry door handle, and no door goes ajar within 60 seconds, the vehicle will re-lock and if equipped will arm the security alarm. • the vehicles security alarm can be armed/disarmed by pushing the passive entry key fob lock/unlock buttons (if equipped). To...

  • Page 46

    To unlock from the passenger side: with a valid passive entry rke transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all doors automatically. The interior door panel lock knob will raise when the door is unlocked. Note: all doors will unlock ...

  • Page 47

    To lock the vehicle’s doors with one of the vehicle’s passive entry rke transmitters within 5 ft (1.5 m) of the driver or passenger front door handles, push the door handle lock button to lock all doors. Do not grab the door handle when pushing the door handle lock button. This could unlock the door...

  • Page 48

    Note: • after pushing the door handle lock button, you must wait two seconds before you can lock or unlock the doors, using either passive entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking. • the pass...

  • Page 49

    The front passenger door for passenger window control and on the rear doors of the quad cab and crew cab models. The windows will operate when the ignition switch is turned to the on/run or acc position, and for up to 10 minutes after the ignition is turned off or until a front door is opened. Note:...

  • Page 50

    Auto-up feature with anti-pinch protection (4-door models driver and front passenger door only) — if equipped lift the window switch fully upward to the second detent, release, and the window will go up automatically. To stop the window from going all the way up during the auto up operation, push do...

  • Page 51

    Window lockout switch (4–door models only) the window lockout switch on the driver’s door allows you to disable the window control on the rear passenger doors. To disable the window controls on the rear passenger doors, push the window lock button into the latched or down position. To enable the win...

  • Page 52

    Wind buffeting wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occur- rence and ...

  • Page 53

    Restraints or belt-positioning booster seats. Older chil- dren who do not use child restraints or belt- positioning booster seats should ride properly buckled up in a vehicle with a rear seat. 4. Never allow children to slide the shoulder belt behind them or under their arm. 5. You should read the i...

  • Page 54

    Seat belt systems buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and could cause a collision that includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can redu...

  • Page 55

    Object is on the outboard front passenger seat or when the seat is folded flat (if equipped). It is recommended that pets be restrained in the rear seat (if equipped) in pet harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed. Beltalert can be activated or deactiva...

  • Page 56

    Warning! (continued) • in a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up...

  • Page 57

    Warning! (continued) • a twisted seat belt may not protect you properly. In a collision, it could even cut into you. Be sure the seat belt is flat against your body, without twists. If you can’t straighten a seat belt in your vehicle, take it to your authorized dealer immediately and have it fixed. ...

  • Page 58

    Warning! (continued) • a frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be re- placed immediately. Do not disassemble or modify the seat belt system. Sea...

  • Page 59

    3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt i...

  • Page 60

    5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfort- able and not resting on your neck. The retractor will withdraw any slack in the shoulder belt. 6. To release the seat belt, push the red button on the buckle. The seat belt will automaticall...

  • Page 61

    2. Grasp the mini-latch plate and pull the seat belt over the seat. 3. Route the shoulder belt to the inside of the [right/ left] head restraint. Inserting latch plate in use position 2 things to know before starting your vehicle 59.

  • Page 62

    4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a “click.” 5. Sit back in seat. Slide the regular latch plate up the webbing as far as necessary to allow the seat belt to go around your lap. 6. When the seat belt is long enough to fit, ins...

  • Page 63

    Warning! (continued) • when reattaching the mini-latch and mini-buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding proce- dure to detach the mini-latch and mini-buckle, untwist the webbing, and reattach the mini-latch and mini-buckle. Lap/shoulder be...

  • Page 64

    As a guide, if you are shorter than average, you will prefer the shoulder belt anchorage in a lower position, and if you are taller than average, you will prefer the shoulder belt anchorage in a higher position. After you release the anchorage button, try to move it up or down to make sure that it i...

  • Page 65

    The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deployed pretensioner or a deployed air bag must be replaced immediately. Seat belt extender if a seat belt is not long enough to fit properly, even when the w...

  • Page 66

    Seat belts and pregnant women we recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the seat belt across the thighs and as snug across the hips as possible. Keep the se...

  • Page 67

    Restraints using the vehicle seat belt” under the “child restraints” section of this manual. The table below defines the type of feature for each seating position. If the passenger seating position is equipped with an alr and is being used for normal usage: only pull the seat belt webbing out far en...

  • Page 68

    As to not activate the alr. If the alr is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in this case and then carefully pull out only the amount of webbing necessary to comfortably wrap around the occupant’s mid-section. Slide the latch ...

  • Page 69

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the seat belt assembly must be replaced if the switchable automati...

  • Page 70

    • knee impact bolsters • advanced front air bags • supplemental side air bags • front and side impact sensors — if equipped • seat belt pretenioners • seat belt buckle switch advanced front air bags this vehicle has advanced front air bags for both the driver and front passenger as a supplement to t...

  • Page 71

    Warning! • being too close to the steering wheel or instrument panel during advanced front air bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. • never place a rear-fa...

  • Page 72

    Warning! • no objects should be placed over or near the air bag on the instrument panel or steering wheel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bags to inflate. • do not put anything on or around the air bag covers or attempt to op...

  • Page 73

    On the other hand, depending on the type and location of impact, advanced front air bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves a...

  • Page 74

    Supplemental side air bags your vehicle is equipped with two types of side air bags: 1. Supplemental seat-mounted side air bags (sabs): located in the outboard side of the front seats. The sabs are marked with a “srs airbag” or “airbag” label sewn into the outboard side of the seats. The sabs may he...

  • Page 75

    When the sab deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating sab deploys through the seat seam into the space between the occupant and the door. The sab moves at a very high speed and with such a high force that it could injure you if you are not seated ...

  • Page 76

    Rollover events, in addition to the injury reduction poten- tial provided by the seat belts and body structure. The sabics deploy downward, covering the side win- dows. An inflating sabic pushes the outside edge of the trim out of the way and covers the window. The sabics inflate with enough force t...

  • Page 77

    The sabics and sabs (“side air bags”) are designed to activate in certain side impacts and certain rollover events. The occupant restraint controller (“orc”) de- termines whether the deployment of the side air bags in a particular side impact or rollover event is appropriate, based on the severity a...

  • Page 78

    Warning! (continued) • relying on the side air bags alone could lead to more severe injuries in a collision. The side air bags work with your seat belt to restrain you properly. In some collisions, side air bags won’t deploy at all. Always wear your seat belt even though you have side air bags. Note...

  • Page 79

    Event may be in progress and whether deployment is appropriate. A slower-developing event may deploy the seat belt pretensioners on both sides of the vehicle. A faster-developing event may deploy the seat belt preten- sioners as well as the sabs and sabics on both sides of the vehicle. The rollover ...

  • Page 80

    Continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- structions for cleaning. Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! De...

  • Page 81

    System reset procedure in order to reset the enhanced accident response system functions after an event, the ignition switch must be changed from ignition start or on/run to ignition off. Air bag warning light the air bags must be ready to inflate for your protection in a collision. The occupant res...

  • Page 82

    Free, if any of the following occurs, have an authorized dealer service the air bag system immediately. • the air bag warning light does not come on during the four to eight seconds when the ignition switch is first turned to the on/run position. • the air bag warning light remains on after the four...

  • Page 83

    Maintaining your air bag system warning! • modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the s...

  • Page 84

    Event data recorder (edr) this vehicle is equipped with an event data recorder (edr). The main purpose of an edr is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems per-...

  • Page 85

    Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the united states, and every canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be pros- ecuted for ignoring it. Ch...

  • Page 86

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck (732–8243). Canadian resi- dents should refer to transport canada’s website for additional information: • www.Tc.Gc.Ca/eng/roadsafety/safedrivers- childsafety-index-53.Htm summary of recommendations for restrainin...

  • Page 87

    Child size, height, weight or age recommended type of child restraint larger children children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the vehicle seat belt, seated in the rear seat of the ve...

  • Page 88

    Warning! • never place a rear-facing child restraint in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear- facing child restraint. • only use a rear-facing child restraint in a vehicle with ...

  • Page 89

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • after a child restraint i...

  • Page 90

    2. Do the child’s knees bend comfortably over the front of the vehicle seat – while they are still sitting all the way back? 3. Does the shoulder belt cross the child’s shoulder between their neck and arm? 4. Is the lap part of the seat belt as low as possible, touching the child’s thighs and not th...

  • Page 91

    Recommendations for attaching child restraints restraint type combined weight of the child + child restraint use any attachment method shown with an “x” below latch – lower anchors only seat belt only latch – lower anchors + top tether anchor seat belt + top tether anchor rear-facing child restraint...

  • Page 92

    Lower anchors and tethers for children (latch) restraint system your vehicle is equipped with the child restraint anchor- age system called latch, which stands for lower anchors and tethers for children. The latch system has three vehicle anchor points for installing latch- equipped child seats. The...

  • Page 93

    Latch positions for installing child restraints in this vehicle standard cab • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol quad cab®/crew cab full bench • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 2 things to kno...

  • Page 94

    Quad cab®/mega cab®/crew cab split bench • lower anchorage symbol 2 anchorages per seating position • top tether anchorage symbol 92 things to know before starting your vehicle.

  • Page 95

    What is the weight limit (child’s weight + weight of the child re- straint) for using the latch an- chorage system to attach the child restraint? 65 lbs (29.5 kg) use the latch anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and ...

  • Page 96

    Can two child restraints be at- tached using a common lower latch anchorage? No never “share” a latch anchorage with two or more child restraints. If the center position does not have dedicated latch lower anchor- ages, use the seat belt to install a child seat in the center position next to a child...

  • Page 97

    Locating the latch anchorages the lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between ...

  • Page 98

    Locating the latch anchorages regular cab models have tether strap anchor- ages behind the front center and right seats. Quad cab®, mega cab® and crew cab mod- els have tether strap anchorages located behind each of the rear seats. 1 — tether strap hook 2 — tether strap to child restraint 3 — tether...

  • Page 99

    Latch-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage. Forward-facing child restraints and some rear-facing infant restraint...

  • Page 100

    Center seat latch — quad cab®/mega cab®/crew cab split bench if a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard latch anchors or seat bel...

  • Page 101

    3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seat- ing position. 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “installing child restraints using the top tether anchorage” for direc- tio...

  • Page 102

    Warning! • improper installation of a child restraint to the latch anchorages can lead to failure of the re- straint. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • child restraint anchorages ar...

  • Page 103

    Lap/shoulder belt systems for installing child restraints in this vehicle standard cab • alr = switchable automatic locking retractor • cinch = cinching latch plate • top tether anchorage symbol quad cab®/mega cab®/crew cab • alr = switchable automatic locking retractor • cinch = cinching latch plat...

  • Page 104

    Lap/shoulder belt systems what is the weight limit (child’s weight + weight of the child re- straint) for using the tether anchor with the seat belt to attach a forward facing child restraint? Weight limit of the child restraint always use the tether anchor when using the seat belt to install a for-...

  • Page 105

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint to get a better fit. If the rear seat can be moved forward and r...

  • Page 106

    The tether strap to the anchorage and tighten the tether strap. See the section “installing child restraints using the top tether anchorage” for directions to attach a tether anchor. 9. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the seat belt pa...

  • Page 107

    6. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. If the buckl...

  • Page 108

    1 — tether strap hook 2 — tether strap to child restraint 3 — tether anchor 2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head r...

  • Page 109

    Warning! Never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rearward facing infant seat. Quad cab® or crew cab trucks: the top tether anchorages in this ve...

  • Page 110

    Right or left outboard seats: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop. 2. Place a child restraint on the seat and adjust the tether strap so that it will reach over the seat back, under the head restraint, through the tether strap lo...

  • Page 111

    3. Pass the tether strap hook under the head restraint behind the child seat, though the tether strap loop behind the seat and over to the center tether strap loop. 4. Attach the hook to the center tether strap loop (see diagram). Tighten the tether strap according to the child seat manufacturer’s i...

  • Page 112

    Note: if there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connected to the center tether strap loop. This is the correct way to tether two outboard child seats. Center seat: 1. Raise the head restraint and reach be...

  • Page 113

    3. Pass the tether strap hook under the head restraint behind the child seat, though the tether strap loop behind the seat and over to the right or left outboard tether strap loop. 4. Attach the hook to the outboard tether strap loop (see diagram). Tighten the tether strap according to the child sea...

  • Page 114

    Installing three child restraints: 1. Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right and left seating positions, above. 2. Attach both hooks to the center tether strap loop, but do not tighten the straps yet. 3. Place a child restraint ...

  • Page 115

    Warning! • an incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • if your vehicle is equipped with a split rear seat, make sure the tethe...

  • Page 116

    Caution! Never use non-detergent oil or straight mineral oil in the engine or damage may result. Note: a new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as a problem. Safety tip...

  • Page 117

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 118

    Safety checks you should make inside the vehicle seat belts inspect the seat belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear s...

  • Page 119

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 120

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 121: Contents

    Understanding the features of your vehicle contents ! Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 ▫ inside day/night mirror — if equipped . . . .126 ▫ automatic dimming mirror — if equipped . . .127 ▫ automatic dimming mirror with rear view camera display — if equipped . . . ....

  • Page 122

    ▫ passenger’s power seat — if equipped . . . . . .145 ▫ power lumbar — if equipped . . . . . . . . . . . .145 ▫ heated seats — if equipped . . . . . . . . . . . . . .146 ▫ ventilated seats — if equipped . . . . . . . . . . . .149 ▫ manual seat adjuster — if equipped. . . . . . . .150 ▫ 40-20-40 fron...

  • Page 123

    ▫ lights-on reminder . . . . . . . . . . . . . . . . . . .172 ▫ battery saver. . . . . . . . . . . . . . . . . . . . . . . . .172 ▫ interior lights . . . . . . . . . . . . . . . . . . . . . . .172 ▫ cargo light . . . . . . . . . . . . . . . . . . . . . . . . .176 ▫ multifunction lever . . . . . . . ...

  • Page 124

    ▫ to accelerate for passing . . . . . . . . . . . . . . . .191 ! Parksense® rear park assist — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . . .191 ▫ parksense® sensors . . . . . . . . . . . . . . . . . . . .192 ▫ parksense® warning display . . . . . . . . . . . . .192 ▫ parksense® d...

  • Page 125

    ▫ programming a non-rolling code . . . . . . . . .218 ▫ canadian/gate operator programming . . . . .220 ▫ using homelink® . . . . . . . . . . . . . . . . . . . .221 ▫ security . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 ▫ troubleshooting tips . . . . . . . . . . . . . . . . . . .222 ▫...

  • Page 126

    ! Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . .237 ▫ glove compartment . . . . . . . . . . . . . . . . . . .237 ▫ door storage. . . . . . . . . . . . . . . . . . . . . . . . .239 ▫ center storage compartment — if equipped . .240 ▫ second row in-floor storage bin — if equipped . . ....

  • Page 127

    ▫ camper applications . . . . . . . . . . . . . . . . . . .268 ! Easy-off tailgate . . . . . . . . . . . . . . . . . . .268 ▫ disconnecting the rear camera or remote keyless entry — if equipped . . . . . . . . . . . . . . . . . . .269 ▫ removing the tailgate. . . . . . . . . . . . . . . . . .270 ▫ l...

  • Page 128

    Mirrors inside day/night mirror — if equipped a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror hea...

  • Page 129

    Automatic dimming mirror — if equipped a single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the wind- shield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can b...

  • Page 130

    Note: the assist and 9–1–1 features operate through the uconnect® access service. These buttons will only operate as long as your uconnect® access service is active. Refer to your “uconnect® system supplement manual” for further information. Assist call the assist button is used to automatically con...

  • Page 131

    3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 call system may transmit the following important vehicle information to a 9-1-1 operator: • indication that the occupant placed a 9-1-1 call. • the vehicle brand. • the last known gps coordinates of the vehicle. 4. You ...

  • Page 132

    Warning! • if anyone in the vehicle could be in danger (e.G., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from a 9-1-1 operator. All occupants should exit the vehicle immediately and move to a safe location. (continued) warning! (continued) • the 9...

  • Page 133

    Warning! (continued) • modifications to any part of the 9-1-1 call system could cause the air bag system to fail when you need it. You could be injured if the air bag system is not there to help protect you. 9-1-1 call system limitations vehicles sold in canada and mexico do not have 9-1-1 call syst...

  • Page 134

    Warning! (continued) • the occupant restraint control module turns on the air bag warning light on the instrument panel if a malfunction in any part of the system is detected. If the air bag warning light is illumi- nated, the air bag system may not be working properly and the 9-1-1 system may not b...

  • Page 135

    Note: never place anything on or near the vehicle’s wireless and gps antennas. You could prevent wireless and gps signal reception, which can prevent your vehicle from placing an emergency call. Wireless and gps signal reception is required for the 9-1-1 call system to function properly. General inf...

  • Page 136

    When the vehicle is placed into reverse gear a video display illuminates to display the image generated by the rear view camera located on the tailgate handle. The auto dimming feature is also disabled to improve rear view viewing. Outside mirrors to receive maximum benefit, adjust the outside mirro...

  • Page 137

    Outside mirrors folding feature all outside mirrors are designed to be able to be manu- ally folded both forward and rearward to prevent dam- age. Caution! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. Tilt mirro...

  • Page 138

    If your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “understand- ing your instrument panel” for further information. If your vehicle is not equipped with a touchscreen, this feature can be programmed through th...

  • Page 139

    Resetting the power folding outside mirrors you may need to reset the power folding mirrors if the following occurs: • the mirrors are accidentally blocked while folding. • the mirrors are accidentally manually folded/ unfolded. • the mirrors come out of the unfolded position. • the mirrors shake an...

  • Page 140

    Power mirrors — if equipped the controls for the power mirrors are located on the driver’s door trim panel. The power mirror controls consist of mirror select but- tons and a four-way mirror control switch. To adjust a mirror, press either the l (left) or r (right) button to select the mirror that y...

  • Page 141

    Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move. Heated mirrors — if equipped these mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster (if equipped). Refer to “rear ...

  • Page 142

    Trailer towing mirrors — if equipped these mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped in or out). Note: fold the trailer towing mirrors rearwa...

  • Page 143

    Illuminated vanity mirror — if equipped illuminated vanity mirrors are located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on auto- matically. Closing the mirror cover turns off the light. “slide-on-rod” features of sun viso...

  • Page 144

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 145

    Driver’s power seat — if equipped some models may be equipped with an eight-way power driver’s seat. The power seat switches are located on the outboard side of the driver’s seat cushion. There are two power seat switches that are used to control the move- ment of the seat cushion and the seatback. ...

  • Page 146

    Adjusting the seat forward or rearward the seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. Adjusting the seat up or down the height of the seats...

  • Page 147

    Warning! (continued) • do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt, which could result in serious injury or death. Caution! Do not place any article under a power seat or impede its abili...

  • Page 148

    Heated seats — if equipped on some models, the front and rear seats may be equipped with heaters located in the seat cushions and seat backs. Warning! • persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, ex...

  • Page 149

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Fro...

  • Page 150

    Vehicles equipped with remote start on models that are equipped with remote start, the heated seats can be programed to come on during a remote start. If your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “unders...

  • Page 151

    • the engine must be running for the heated seats to operate. When the high-level setting is selected, the heater will provide a boosted heat level during the first four minutes of operation. Then, the heat output will drop to the normal high-level. If the high-level setting is selected, the system ...

  • Page 152

    Vehicles equipped with remote start on models that are equipped with remote start, the ventilated seats can be programed to come on during a remote start. If your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “un...

  • Page 153

    Have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Warning! • adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision a...

  • Page 154

    40-20-40 front bench seat — if equipped the seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat. On some models the back of the center portion (20%) easily folds down to provide an armrest/center storage compartment. Mega cab® rear seat feature...

  • Page 155

    Folding rear seat (table mode) — if equipped both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 1. Lift the handle, located next to the head restraint. 2. Fold the seatback forward. 3. Lift the seatback, to return the seat to the upright...

  • Page 156

    Folding rear seat — if equipped both the outboard rear seats will drop and move forward when the seatback is folded flat. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed...

  • Page 157

    2. Fold the seatback down and push the seat forward. 3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place. Folding rear seat handle rear passenger fold-flat seats 3 understanding the features of your vehicle 155.

  • Page 158

    Warning! An improperly latched seat could cause serious in- jury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. Head restraints head restrai...

  • Page 159

    Warning! A loose head restraint thrown forward in a collision or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow re- moved head restraints in a location outside the occu- pant compartment. Warning! All the head restraints must be reinstalled in the veh...

  • Page 160

    Rear head restraints the rear seats are equipped with adjustable head re- straints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, press the adjustment button, located on the base of the head restraint, and push downward on the head restraint. Note: • th...

  • Page 161

    Presets. Your remote keyless entry (rke) transmitter can also be programmed to recall the same positions when the unlock button is pressed. Note: your vehicle is equipped with two rke trans- mitters, one rke transmitter can be linked to memory position 1 and the other transmitter can be linked to me...

  • Page 162

    Programming the memory feature note: to create a new memory profile, perform the following: 1. Cycle the vehicles ignition to the on/run position (do not start the engine). 2. Adjust all memory profile settings to desired prefer- ences (seat, side mirrors, adjustable pedals and radio station presets...

  • Page 163

    Uconnect® system. Refer to “uconnect® settings ” in “understanding your instrument panel” for further information. • if your vehicle is not equipped with a touchscreen, you must select the “key fob linked to memory” feature through the electronic vehicle information center (evic) or driver informati...

  • Page 164

    Memory position recall note: for vehicles equipped with an automatic trans- mission, the vehicle must be in park to recall memory positions. If a recall is attempted when the vehicle is not in park, a message will be displayed in the electronic vehicle information center (evic) or driver information...

  • Page 165

    Easy entry/exit seat this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. The distance the driver seat moves depends on where you have the driver seat positioned when you remove the key fob from the ignition (or change the ignition...

  • Page 166

    Note: the easy entry/exit feature is not enabled when the vehicle is delivered from the factory. The easy entry/exit feature is enabled (or later disabled) through the programmable features in the uconnect® system. Refer to “uconnect® settings/customer programmable features” in “understanding your i...

  • Page 167

    Caution! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle...

  • Page 168

    Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less suscep- tible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility ...

  • Page 169

    Automatic headlights — if equipped this system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch to the auto position. When the system is on, the headlight delay feature is also on. This means the headlights will stay o...

  • Page 170

    If your vehicle is not equipped with a touchscreen, this feature can be programmed through the electronic ve- hicle information center (evic) or driver information display (did). Refer to “electronic vehicle information center (evic)” or “driver information display (did)” in “understanding your inst...

  • Page 171

    Center (evic)” or “driver information display (did)” in “understanding your instrument panel” for further in- formation. Automatic high beam headlamp control — if equipped the automatic high beam headlamp control system provides increased forward lighting at night by automat- ing high beam control t...

  • Page 172

    • to opt out of the advanced auto high-beam sensitiv- ity control (default) and enter reduced high-beam sensitivity control (not recommended), toggle high- beam lever 6 full on/off cycles within 10 seconds of ignition on. System will return to default setting upon ignition off. If the windshield or ...

  • Page 173

    2. Push back on the multifunction lever once again to reactivate the system. Parking lights and panel lights to turn on the parking lights and instrument panel lights, rotate the headlight switch clockwise. To turn off the parking lights, rotate the headlight switch back to the o (off) position. Fog...

  • Page 174

    Lights-on reminder if the headlights, parking lights, or cargo lights are left on after the ignition is turned off, a chime will sound when the driver’s door is opened. Battery saver to protect the life of your vehicle’s battery, load shedding is provided for both the interior and exterior lights. I...

  • Page 175

    The brightness of the instrument panel as well as the ambient lighting can be regulated by rotating the dimmer control right (brighter) or left (dimmer). When the head- lights are on you can supplement the brightness of the odometer, trip odometer, radio and overhead console by rotating the control ...

  • Page 176

    Courtesy/reading lights both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the unlock button is pressed on the remote keyless ent...

  • Page 177

    Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned off, they will automatically turn off after 15 minutes. Ambient light the overh...

  • Page 178

    Cargo light the cargo lights are turned on by pressing on the cargo button. The cargo lights will also turn on for approximately 30 seconds when a rke transmitter unlock button is pressed, as part of the illuminated entry feature. Multifunction lever the multifunction lever is located on the left si...

  • Page 179

    Note: if either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is defective. Lane change assist tap the lever up or down once, without ...

  • Page 180

    High/low beam switch push the multifunction lever toward the instrument panel to switch the headlights to high beam. Pulling the multifunction lever back toward the steering wheel will turn the low beams back on, or shut the high beams off. Windshield wipers and washers windshield wipers the wipers ...

  • Page 181

    Windshield wiper operation rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper opera- tion. Intermittent wiper system the inte...

  • Page 182

    Warning! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use. Mist feature when...

  • Page 183

    The sensitivity of the system can be adjusted with the multifunction lever. Wiper delay position 1 is the least sensitive, and wiper delay position 5 is the most sensi- tive. Setting 3 should be used for normal rain conditions. Settings 1 and 2 can be used if the driver desires less wiper sensitivit...

  • Page 184

    Remote start mode inhibit — on vehicles equipped with remote starting system, rain sensing wipers are not operational when the vehicle is in the remote start mode. Once the operator is in the vehicle and has placed the ignition switch in the run position, rain sensing wiper operation can resume, if ...

  • Page 185

    Warning! (continued) the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. Heated steering wheel — if equipped the steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one t...

  • Page 186

    If your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “understand- ing your instrument panel” for further information. If your vehicle is not equipped with a touchscreen, this feature can be programmed through th...

  • Page 187

    Driver adjustable pedals — if equipped the adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows the brake, accelerator, and clutch pedals (if equipped) to move toward or away from the driver to provide improved...

  • Page 188

    If the pedals are attempted to be adjusted when the system is locked out (“adjustable pedal disabled — cruise control engaged” or “adjustable pedal disabled — vehicle in reverse”. Note: • always adjust the pedals to a position that allows full pedal travel. • further small adjustments may be necessa...

  • Page 189

    The electronic speed control buttons are located on the right side of the steering wheel. Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic ...

  • Page 190

    Warning! Leaving the electronic speed control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system off when you are not using it. To set a desired speed turn the elec...

  • Page 191

    The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “ under- standing your instrument panel” for more information. The speed increment shown is dependant on the selected speed unit of u.S. (mph) or metric (km/h): u.S. Speed (mph) • pressing the res...

  • Page 192

    To decrease speed when the electronic speed control is set, you can de- crease speed by pushing the set (-) button. The drivers preferred units can be selected through the instrument panel settings if equipped. Refer to “ under- standing your instrument panel” for more information. The speed decreme...

  • Page 193

    To accelerate for passing press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using electronic speed control on hills the transmission may downshift on hills to maintain the vehicle set speed. Note: the electronic speed control system ma...

  • Page 194

    Parksense® will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to the on/run position. Parksense® can be active only when the shift lever/gear selector is in reverse. If parksense® is enabled at this shift lever/gear selector position, th...

  • Page 195

    The parksense® warning screen will only be displayed if sound and display is selected. Note: if your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “understand- ing your instrument panel” for further information. ...

  • Page 196

    Single 1/2 second tone slow tone 194 understanding the features of your vehicle.

  • Page 197

    Fast tone continuous tone 3 understanding the features of your vehicle 195.

  • Page 198

    The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-45 in (200-115 cm) ...

  • Page 199

    Adjustable chime volume settings the rear chime volume settings are programmable. • if your vehicle is equipped with a touchscreen, the settings may be programmed through the uconnect® system. Refer to “uconnect® settings ” in “under- standing your instrument panel” for further informa- tion. • if y...

  • Page 200

    The parksense® switch led will be on when parksense® is disabled or defective. The parksense® switch led will be off when the system is enabled. If the parksense switch is pressed, and the system is disabled or requires service, the parksense switch led will blink momentarily, and then the led will ...

  • Page 201

    Cleaning the parksense® system clean the parksense® sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do not scratch or poke the sensors. Otherwise, you could dam- age the sensors. Parksense® system usage precautions note: • ensure that the rear bumper is free of s...

  • Page 202

    System misinterpreting a close obstacle as a sensor problem, causing the #parksense unavailable service required# message to be displayed in the instrument cluster. • on vehicles equipped with a tailgate, parksense® should be disabled when the tailgate is in the lowered or open position and the vehi...

  • Page 203

    Warning! (continued) • before using parksense®, it is strongly recom- mended that the ball mount and hitch ball assem- bly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be...

  • Page 204

    Parksense® sensors the four parksense® sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 18 in (45 cm) up to 79 in (200 cm) from the rear fascia/bumper in the horizontal dire...

  • Page 205

    Note: if your vehicle is equipped with a touchscreen, this feature can be programmed through the uconnect® system. Refer to “uconnect® settings” in “understand- ing your instrument panel” for further information. If your vehicle is not equipped with a touchscreen, this feature can be programmed thro...

  • Page 206

    The vehicle is close to the obstacle when the display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: warning alerts rear distance (in/cm) greater than 79 in (200 cm) 79-45 in (200-115 cm) 45-31 in (...

  • Page 207

    Front park assist audible alerts parksense® will turn off the front park assist audible alert (chime) after approximately three seconds when an obstacle has been detected, the vehicle is stationary, and brake pedal is applied. Adjustable chime volume settings the front and rear chime volume settings...

  • Page 208

    When the shift lever is moved to reverse and the front or rear system is disabled, the evic/did will display the #front parksense off# or #rear parksense off# message for five seconds, followed by a car graphic with #off# in the corresponding side. This car graphic will be displayed for as long as t...

  • Page 209

    Is functioning properly. These arc alerts will interrupt the # parksense unavailable wipe rear sensors#, # parksense unavailable wipe front sen- sors#, or #parksense unavailable service re- quired# messages if an object is detected within the five second pop-up duration. The car graphic will remain ...

  • Page 210

    • when you turn front or rear parksense® off, the instrument cluster will display “front parksense off” or “rear parksense off.” furthermore, once you turn front or rear parksense® off, it remains off until you turn it on again, even if you cycle the ignition key. • when you move the shift lever to ...

  • Page 211

    Caution! • parksense® is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • the vehicle m...

  • Page 212

    Warning! (continued) • before using parksense®, it is strongly recom- mended that the ball mount and hitch ball assem- bly is disconnected from the vehicle when the vehicle is not used for towing. Failure to do so can result in injury or damage to vehicles or obstacles because the hitch ball will be...

  • Page 213

    When the vehicle is shifted out of reverse (with camera delay turned on), the rear camera image will be dis- played for up to 10 seconds after shifting out of #re- verse# unless the forward vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into #park# or the ignition is switched to ...

  • Page 214

    Warning! (continued) must continue to pay attention while backing up. Failure to do so can result in serious injury or death. Caution! • to avoid vehicle damage, parkview® should only be used as a parking aid. The parkview® camera is unable to view every obstacle or object in your drive path. • to a...

  • Page 215

    Courtesy/reading lights both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the unlock button is pressed on the remote keyless ent...

  • Page 216

    Note: the courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. If the interior lights are left on after the ignition is turned off, they will automatically turn off after 15 minutes. Garage door opener — if...

  • Page 217

    Note: homelink® is disabled when the vehicle secu- rity alarm is active. Before you begin programming homelink® ensure your vehicle is parked outside of the garage before you begin programming. For efficient programming and accurate transmission of the radio-frequency signal it is recommended that a...

  • Page 218

    Note: • for vehicle’s equipped with keyless enter-n-go™, place the ignition in the run position with the engine on. • erasing all channels should only be performed when programming homelink® for the first time. Do not erase channels when programming additional buttons. • if you have any problems, or...

  • Page 219

    2. Place the hand - held transmitter 1 to 3 inches (3 to 8 cm) away from the homelink® button you wish to program. 3. Push and hold the homelink® button you want to program while you push and hold the hand - held transmitter button. 4. Continue to hold both buttons until the evic/did display changes...

  • Page 220

    Reprogramming a single homelink® button (rolling code) to reprogram a channel that has been previously trained, follow these steps: 1. Turn the ignition switch to the on/run position. For vehicle’s equipped with keyless enter-n-go™, place the ignition in the run position with the engine on. 2. Push ...

  • Page 221

    Note: • it may take up to 30 seconds or longer in some cases for the channel to train. • if the evic/did displays “did not train” repeat from step 2. 5. Push and hold the programmed homelink® button. The evic/did will display “channel # trans- mit.” if the garage door opener/device activates, progra...

  • Page 222

    Canadian/gate operator programming for programming transmitters in canada/united states that require the transmitter signals to “time-out” after several seconds of transmission. Canadian radio frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of trans- mission ...

  • Page 223

    5. Push and hold the programmed homelink® button. The evic/did will display “channel # trans- mit.” if the device is plugged in and activates, pro- gramming is complete. If you unplugged the garage door opener/device for programming, plug it back in at this time. Reprogramming a single homelink® but...

  • Page 224

    Interactive display (did) will display “clearing channels.” release the buttons when the evic/did displays “channels cleared.” the homelink® universal transceiver is disabled when the vehicle security alarm is active. Troubleshooting tips if you are having trouble programming homelink®, here are som...

  • Page 225

    Warning! (continued) use a garage door opener without these safety fea- tures. Call toll-free 1-800-355-3515 or, on the internet at homelink.Com for safety information or assis- tance. General information this device complies with fcc rules part 15 and industry canada rss-210. Operation is subject t...

  • Page 226

    Power sunroof — if equipped the power sunroof switch is located on the overhead console between the courtesy/reading lights. Warning! • never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to ...

  • Page 227

    Warning! (continued) • do not allow small children to operate the sunroof. Never allow your fingers, other body parts, or any object, to project through the sunroof opening. Injury may result. Opening sunroof — manual mode to open the sunroof, press and hold the switch rearward to full open. Any rel...

  • Page 228

    Pinch protect feature this feature will detect an obstruction in the opening of the sunroof during express close operation. If an ob- struction in the path of the sunroof is detected, the sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and ...

  • Page 229

    Sunroof maintenance use only a nonabrasive cleaner and a soft cloth to clean the glass panel. Ignition off operation the power sunroof switch will remain active for up to approximately ten minutes after the ignition switch is turned to the lock position. Opening either front door will cancel this fe...

  • Page 230

    The auxiliary power outlets can be found in the following locations: caution! • do not exceed the maximum power of 160 watts (13 amps) at 12 volts. If the 160 watts (13 amps) power rating is exceeded, the fuse protecting the system will need to be replaced. • power outlets are designed for accessory...

  • Page 231

    • center console when equipped with bucket seats. • inside the upper lid of the center storage compartment — if equipped. Power outlet — center console power outlet — upper lid 3 understanding the features of your vehicle 229.

  • Page 232

    • rear of the center console storage compartment — quad cab® or crew cab. Power outlet — rear center console power outlet — rear center console fuse 230 understanding the features of your vehicle.

  • Page 233

    The key symbol indicates that this outlet can supply power when the key is in the on/run or acc posi- tions. All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge. Warning! To avoid serious injury or death: ...

  • Page 234

    Caution! • many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.E., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • ac...

  • Page 235

    Power inverter — if equipped a 115 volt (150 watts maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 watts. Certain high-end video games, such as ...

  • Page 236

    To turn on the power outlet, simply plug in the device. The outlet automatically turns off when the device is unplugged. Note: due to built-in overload protection, the power inverter will shut down if the power rating is exceeded. Warning! To avoid serious injury or death: • do not insert any object...

  • Page 237

    Front instrument panel cupholders — floor mounted shifter for vehicles equipped with bucket seats there are two cupholders located in the floor console. Rear cupholder — quad cab® quad cab® vehicles may be equipped with a rear cupholder that consists of two cup wells for rear passen- ger convenience...

  • Page 238

    Rear cupholder — crew cab crew cab vehicles are equipped with rear cupholders located in the center armrest. Crew cab vehicles may be equipped with a rear cup- holder that consists of two cup wells for rear passenger convenience. Crew cab rear armrest cupholder rear cup wells 236 understanding the f...

  • Page 239

    Storage glove compartment the glove compartment is located on the passenger side of the instrument panel and features both an upper and lower storage area. Glove compartment 1 — upper glove compartment 2 — lower glove compartment 3 understanding the features of your vehicle 237.

  • Page 240

    To open the upper glove compartment push upward on the handle release. The glove compartment door will automatically open. To open the lower glove compartment, pull on the handle to release the latch and lower the glove compartment door. Upper glove compartment lower glove compartment 238 understand...

  • Page 241

    Door storage front door storage — if equipped storage areas and bottle holders (drivers side only) are located in the door trim panels. Rear door storage — crew cab storage compartments are located in both the driver and passenger door trim panels. Front door storage rear door storage 3 understandin...

  • Page 242

    Center storage compartment — if equipped the center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Warning! • this armrest is not a seat. Anyone seated on the armrest could be seri...

  • Page 243

    With the upper lid closed, pull on the lower handle to open the lower storage bin. Warning! Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision. Upper storage compartment lower storage bi...

  • Page 244

    Second row in-floor storage bin — if equipped in-floor storage bins are located in front of the second row seats and can be used for extra storage. The storage bins have removable liners that can be easily removed for cleaning. To open in-floor storage bin, lift upward on the handle of the latch and...

  • Page 245

    Seatback storage located in the back of both the driver and passenger front seats are pockets that can be used for storage. Storage (regular cab) the storage bin is located behind the front seats and runs the length of the cab. Drivers side seatback storage storage bin 3 understanding the features o...

  • Page 246

    Storage and seats (crew cab) the crew cab models provide additional storage under the rear seats. Lift the seats to access the storage com- partment. To open the storage compartments, lift upward on the handle of the latch and open the lid. Caution! Always lift the storage compartment lids by using ...

  • Page 247

    Plastic grocery bag retainers (regular cab models) retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat. Rear window features rear window defroster the rear window defroster button is located on the climate control panel. Press thi...

  • Page 248

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 249

    Manual sliding rear window — if equipped a locking device in the center of the window helps to prevent entry from the rear of the vehicle. Squeeze the lock to release the window. Fold flat load floor — if equipped quad cab® and crew cab models with a 60/40 rear seat may be equipped with a folding lo...

  • Page 250

    3. Reverse the procedure to store the load floor. Unfolding the load floor/crew cab® 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unfold both the legs using the straps. Load floor in open position load floor legs in stowed position 248 understanding the features of your vehicle.

  • Page 251

    3. Lift the front panel until the load floor unfolds into position. 4. Reverse the procedure to store the load floor. Load floor legs in opened position load floor in open position 3 understanding the features of your vehicle 249.

  • Page 252

    Positioning the load floor for storage access under the seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3. Lift the load floor up to access storage under the load floor. Warning! Do not drive with the load floor in ...

  • Page 253

    Crew cab® — if equipped 4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. Pickup box the pickup box has many features designed for utility and convenience. Load floor securing straps/crew cab® pick up box features 1 — upper load floor in...

  • Page 254

    Note: if you are installing a toolbox, ladder rack or headache rack at the front of the pickup box, you must use mopar box reinforcement brackets that are available from your authorized dealer. You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place l...

  • Page 255

    There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box. There are four tie-down cleats bolted to the lower sides of the picku...

  • Page 256

    Note: the cargo camera image may be deactivated by pressing the uconnect® display. The previous selected screen will appear. Rambox® — if equipped the rambox® system is an integrated pickup box stor- age and cargo management system consisting of three features: • integrated box side storage bins • c...

  • Page 257

    Caution! Failure to follow the following items could cause damage to the vehicle: • assure that all cargo inside the storage bins is properly secured. • do not exceed cargo weight rating of 150 lb (68 kg) 1500 series vehicles or 300 lbs (136 kg) for 2500 and 3500 series vehicles per bin. To open a s...

  • Page 258

    Caution! Leaving the lid open for extended periods of time could cause the vehicle battery to discharge. If the lid is required to stay open for extended periods of time, (continued) caution! (continued) it is recommended that the bin lights be turned off manually using the on/off switch. Cargo bins...

  • Page 259

    The storage bin, insert the key into the keyhole on the pushbutton and turn clockwise to lock or counterclock- wise to unlock. Always return the key to the upright (vertical) position before removing the key from the pushbutton. Caution! • ensure cargo bin lids are closed and latched before moving o...

  • Page 260

    Rambox® storage bin cover emergency release lever — if equipped as a security measure, a storage bin cover emergency release is built into the storage bin cover latching mecha- nism. Note: in the event of an individual being locked inside the storage bin, the storage bin cover can be opened from ins...

  • Page 261

    1. Make sure the center handle is unlocked using the vehicle key and rotate the center handle vertically to release the extender side gates. 2. With the side gates open, position the extender fully forward in the bed against the front panel. 3. Rotate the side gates closed allowing the outboard ends...

  • Page 262

    4. Rotate the center handle horizontally to secure the side gates in the closed position. 5. Lock the center handle using the vehicle key to secure the panel into place. Cargo tie down loop side gates closed 260 understanding the features of your vehicle.

  • Page 263

    Divider position the divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions to assist in managing your cargo. To install the bed extender into a divider po...

  • Page 264

    3. Rotate the side gates closed so that the outboard ends are secured into the intended slots of the bed. 4. Rotate the center handle horizontally to secure the side gates in the closed position. 5. Lock the center handle to secure the panel into place. Aligning gate to slots side gates closed 262 u...

  • Page 265

    Extender position the extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed. The extender position utilizes a locating pin and rotating handle located on both...

  • Page 266

    To install the bed extender into the extender position perform the following: 1. Lower the tailgate. 2. Make sure the center handle is unlocked and rotate the center handle vertically in order to release the ex- tender side gates. 3. Fit the end of the side gate ends onto the pin and handle. 4. Rota...

  • Page 267

    Warning! To reduce the risk of potential injury or property damage: • cargo must be secured. (continued) warning! (continued) • do not exceed cargo load rating of your vehicle. • secure all loads to truck utilizing cargo tie downs. • extender should not be used as cargo tie down. • when vehicle is i...

  • Page 268

    Bed rail tie-down system caution! The maximum load per cleat should not exceed 250 lbs (113 kg) and the angle of the load on each cleat should not exceed 45 degrees above horizontal, or damage to the cleat or cleat rail may occur. There are two adjustable cleats on each side of the bed that can be u...

  • Page 269

    Out on the cleat and slide it to the detent nearest the desired location. Make sure the cleat is seated in the detent and tighten the nut. To remove the cleats from the utility rail, remove the end cap screw located in the center of the end cap, using a #t30 torx® head driver. Remove the end cap and...

  • Page 270

    Slide-in campers camper applications certain truck models are not recommended for slide-in campers. To determine if your vehicle is excluded, please refer to the “consumer information truck-camper load- ing” document available from your authorized dealer. For safety reasons, follow all instructions ...

  • Page 271

    Disconnecting the rear camera or remote keyless entry — if equipped 1. Open the tailgate to access the rear camera or rke connector bracket located on the rear sill. 2. Remove the connector bracket from the sill by press- ing inward in the locking tab. 3. Disconnect the chassis wiring harness, ensur...

  • Page 272

    5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate. This will pre- vent damaging the connector and bracket when stor- ing or r...

  • Page 273

    5. Slide the entire tailgate to the right to free the left side pivot. 6. Remove the tailgate from the vehicle. Note: do not carry the tailgate loose in the truck pickup box. Warning! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “cap or slide-in ca...

  • Page 274

    Tri-fold tonneau cover removal to remove the tonneau cover follow the following steps: 1. Lower the tailgate to gain access to the first set of two tonneau cover clamps located on the driver and pas- sengers under side of the tonneau cover. 2. Pull down on the first set of clamps on both driver and ...

  • Page 275

    3. Pull down on the clamp wire and push the clamp up into the proper released position. Note: be sure the clamp and clamp wire is in the proper released position. Semi clamped position proper released position 3 understanding the features of your vehicle 273.

  • Page 276

    Caution! Make sure the tonneau cover clamp and clamp wire is in the proper released position. If the clamp and clamp wire is not properly released, damage to the tonneau cover material will result. 4. Pick up on the tonneau cover and fold it back onto the second panel. 5. Pick up on the cover and fo...

  • Page 277

    7. Pull down on the clamp wire and push the clamp up into the proper released position. 8. Be sure to clip both stowage straps together to insure the cover stays together. Semi clamped position proper released position 3 understanding the features of your vehicle 275.

  • Page 278

    9. With two people remove the cover. Note: be sure the tonneau cover has been folded completely before removing. Tri-fold tonneau cover installation to install the tonneau cover follow the following steps: 1. Position the folded tonneau cover on the truck bed and push the cover forward against the f...

  • Page 279

    3. Push clamp wires up and under the flange of box (or flange of ram box rail, if equipped) to the semi clamped position. 4. Push clamp handles upward to the clamped position to properly engage the clamps. Stowed position semi clamped position 3 understanding the features of your vehicle 277.

  • Page 280

    Note: once clamped, be sure the clamps are not par- tially clamped to the truck bed flange. 5. Disengage the stowage straps. 6. Unfold tonneau cover to the intermediate position. Note: the vehicle cannot be driven when the tonneau cover is in this position. Clamped position improper clamp position 2...

  • Page 281

    7. Completely unfold the tonneau cover. 8. Pull down on the second set of clamp handles to release the clamps from the stowed position. Intermediate position (vehicle cannot be driven) fully unfolded position 3 understanding the features of your vehicle 279.

  • Page 282

    9. Push clamp wires up and under the flange of box (or flange of ram box rail, if equipped) to the semi clamped position. 10. Push clamp handles upward to the clamped position to properly engage the clamps. Stowed position semi clamped position 280 understanding the features of your vehicle.

  • Page 283

    Note: once clamped, be sure the clamps are not par- tially clamped to the truck bed flange. The tonneau cover clamps can be locked when in the clamped position by placing a lock through the locking hole. Clamped position improper clamp position 3 understanding the features of your vehicle 281.

  • Page 284

    Caution! It is the driver’s responsibility to ensure the tonneau cover is properly installed on the vehicle. Failure to follow this procedure can result in detachment of the tonneau cover from the vehicle and/or damage to the vehicle/tonneau cover. Tri-fold tonneau cover cleaning for proper cleaning...

  • Page 285: Contents

    Understanding your instrument panel contents ! Instrument panel features . . . . . . . . . .286 ! Instrument cluster — midline (evic) . .287 ! Instrument cluster — premium (did) . .288 ! Instrument cluster descriptions . . . . .289 ! Electronic vehicle information center (evic) . . . . . . . . . . ....

  • Page 286

    ▫ did white telltales . . . . . . . . . . . . . . . . . . . .345 ▫ did selectable menu items . . . . . . . . . . . . . .346 ! Uconnect® settings . . . . . . . . . . . . . . . . . . .356 ▫ buttons on the faceplate. . . . . . . . . . . . . . . .357 ▫ buttons on the touchscreen. . . . . . . . . . . . ....

  • Page 287

    ! Uconnect® voice recognition . . . . . . . . . . . . . .422 ▫ introducing uconnect® . . . . . . . . . . . . . . . . .422 ▫ get started . . . . . . . . . . . . . . . . . . . . . . . . . .423 ▫ basic voice commands. . . . . . . . . . . . . . . . . .424 ▫ radio . . . . . . . . . . . . . . . . . . . . ...

  • Page 288

    Instrument panel features 1 — headlight switch 7 — 115v power inverter outlet 13 — gear selector/transfer case position switch — if equipped 2 — instrument cluster 8 — power outlet — if equipped 14 — ignition switch 3 — radio 9 — lower switch bank 15 — hood release 4 — hazard switch 10 — instrument ...

  • Page 289

    Instrument cluster — midline (evic) electronic vehicle information display (evic) 4 understanding your instrument panel 287.

  • Page 290

    Instrument cluster — premium (did) driver information display (did) 288 understanding your instrument panel.

  • Page 291

    Instrument cluster descriptions 1. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). Caution! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engine operation over 3200 rpm (redline) can result in significant damage that ...

  • Page 292

    Testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condi- tion investigated promptly. If this light comes on and remains on whil...

  • Page 293

    Note: • a continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on. • check for an inoperative outside light bulb if either indicator remains on and does not flash, or flashes at a rapid rate. 5. Voltmeter when the engine is running, the gauge indicat...

  • Page 294

    Hydraulic system malfunction or that a problem with the brake booster has been detected by the anti-lock brake system (abs) / electronic stability control (esc) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ...

  • Page 295

    Unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the on/run posi- tion. Note: this light shows only that the ...

  • Page 296

    10. Oil pressure gauge — if equipped the pointer should always indicate some oil pres- sure when the engine is running. A continuous high or low reading under normal driving conditions may indi- cate a lubrication system malfunction. Immediate service should be obtained from an authorized dealer. 11...

  • Page 297

    Placard or tire inflation pressure label, you should deter- mine the proper tire inflation pressure for those tires). As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (tpms) that illuminates a low tire pressure telltale when one or more of your tires ...

  • Page 298

    Caution! The tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, t...

  • Page 299

    Note: the highest available transmission gear is dis- played in the lower right corner of the evic/did whenever the electronic range select (ers) feature is active. Use the +/- selector on the shift lever to activate ers. Refer to “automatic transmission” in “starting and operating” for further info...

  • Page 300

    Note: • the “esc off indicator light” and the “esc activation/malfunction indicator light” come on momentarily each time the ignition switch is turned to on/run. • each time the ignition is turned to on/run, the esc system will be on, even if it was turned off previously. • the esc system will make ...

  • Page 301

    Warning! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “maintaining your vehicle.” follow the warnings unde...

  • Page 302

    If the light remains lit with the engine running, your vehicle will usually be drivable. However, see an autho- rized dealer for service as soon as possible. If the light is flashing when the engine is running, immediate service is required. You may experience reduced performance, an elevated/rough ...

  • Page 303

    32. 4wd auto indicator light — if equipped this light alerts the driver that the vehicle is in the four-wheel drive auto mode, and the front axle is engaged, but the vehicle’s power is sent to the rear wheels. Four-wheel drive will be automatically engaged when the vehicle senses a loss of traction....

  • Page 304

    Electronic vehicle information center (evic) the electronic vehicle information center (evic) fea- tures a driver-interactive display that is located in the instrument cluster. The evic menu items consists of the following: • speedometer • vehicle info • fuel economy info • trip a • trip b • stop/st...

  • Page 305

    The system allows the driver to select information by pushing the following evic control buttons located on the left side of the steering wheel: • up arrow button push and release the up arrow button to scroll upward through the main menu items. • down arrow button push and release the down arrow bu...

  • Page 306

    • left arrow button push and release the left arrow button to return to the main menu, to exit the main menu push and release the up or down arrow to highlight turn menu off, then push and re- lease the right arrow. Electronic vehicle information center (evic) displays — 3.5” display the evic displa...

  • Page 307

    1. Compass display displays the current direction. For further information, refer to “compass settings” under “customer program- mable features — uconnect® 5.0/8.4 settings”. 2. Temperature display displays the temperature in degrees celsius or degrees fahrenheit. 3. Main screen displays main menu, ...

  • Page 308

    • unstored messages this message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are “turn signal on” (if a turn signal is left on) and “lights on” (if driver leaves the vehicle). • unstored messages until run these messages ...

  • Page 309

    3. Press and release the right arrow button to access the ”oil life” screen. 4. Press and release the down arrow button to select “reset”, then press and release the right arrow button to select reset of the oil life to 100%. 5. Press and release the up arrow button to exit the evic screen. Vehicles...

  • Page 310

    • service airbag system • traction control off • washer fluid low • oil pressure low • oil change due • fuel low • service antilock brake system • service electronic throttle control • service power steering • cruise off • cruise ready • cruise set to xxx mph • tire pressure screen with low tire(s) ...

  • Page 311

    • turn signal on • sound horn with remote lock: off; 1st press; 2nd press • vehicle not in park • key in ignition • key in ignition lights on • remote start active key to run • remote start active push start button • remote start aborted fuel low • remote start aborted too cold • remote start aborte...

  • Page 312

    • automatic unavailable use autostick service req. • transmission getting hot press brake • trans. Hot stop safely shift to park wait to cool • transmission cool ready to drive • trailer brake disconnected • service transmission • service shifter • engage park brake to prevent rolling • transmission...

  • Page 313

    • battery low start engine to change ride height • stop/start ready – if equipped • stop/start not ready – if equipped • stop/start not ready hood open – if equipped • stop/start not ready battery charging – if equipped • stop/start not ready trailer tow/haul selected – if equipped • stop/start not ...

  • Page 314

    • stop/start not ready steering wheel turned – if equipped • stop/start autostop active – if equipped • stop/start to restart press clutch or shift to neutral – if equipped • stop/start req’d fault detected – if equipped • stop/start cannot autostart hood open – if equipped • stop/start unavailable ...

  • Page 315

    Do not operate the vehicle until the cause is corrected. This light does not show how much oil is in the engine. The engine oil level must be checked under the hood. • oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the ...

  • Page 316

    Required. You may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. • engine temperature warning light this light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches h, this indicator will illuminate and...

  • Page 317

    • windshield washer fluid low indicator this telltale will turn on to indicate the wind- shield washer fluid is low. • low coolant level indicator this telltale will turn on to indicate the vehicle coolant level is low. • transmission temperature warning telltale this telltale indicates that the tra...

  • Page 318

    • air suspension payload protection telltale — if equipped this telltale will turn on to indicate that the maximum payload may have been exceeded or load leveling cannot be achieved at its current ride height. Protection mode will automatically be selected in order to “protect” the air suspension sy...

  • Page 319

    Evic selectable menu items push and release the up or down arrow buttons until the desired selectable menu item is highlighted in the evic. Speedometer push and release the up or down arrow button until the speedometer menu item is highlighted in the evic. Push and release the right arrow button to ...

  • Page 320

    • average fuel economy value • range to empty trip a push and release the up or down arrow button until the trip a menu item is highlighted in the evic. The trip a information will display the following: • distance • average mpg • elapsed time push and hold right arrow button to reset all informa- t...

  • Page 321

    Air suspension — if equipped push and release the up or down arrow button until the air suspension menu item is highlighted in the evic. Push and release the right arrow button to display the air suspension status. Trailer tow push and release the up or down arrow button until the trailer tow menu i...

  • Page 322

    • service electronic throttle control • service power steering • cruise off • cruise ready • cruise set to xxx mph • tire pressure screen with low tire(s) “inflate tire to xx” • tire pressure information system (tpis) • service tire pressure system • parking brake engaged • brake fluid low • service...

  • Page 323

    • remote start aborted fuel low • remote start aborted too cold • remote start aborted door open • remote start aborted hood open • remote start aborted trunk open • remote start aborted time expired • remote start disabled start to reset • service airbag system • service airbag warning light • driv...

  • Page 324

    • transmission too cold idle with engine on • washer fluid low • service air suspension system • heavy duty air suspension system disable • normal ride height achieved • aerodynamic ride height achieved • off road 1 ride height achieved • off road 2 ride height achieved • entry/exit ride height achi...

  • Page 325

    • stop/start not ready fuel level low – if equipped • stop/start not ready steep incline – if equipped • stop/start not ready extreme outside temperature – if equipped • stop/start not ready engine temperature too high – if equipped • stop/start not ready engine temperature too low – if equipped • s...

  • Page 326

    • stop/start to restart shift out of park – if equipped • stop/start off – if equipped • autostop duration – if equipped the reconfigurable telltales section is divided into the white telltales area on the right, yellow telltales in the middle, and red telltales on the left. Screen setup push and re...

  • Page 327

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 1 language select language english, spanish, french, italian, german, dutch 2 units units u.S.; metric 3 parksense parksense • notification — sound only; sound & display • front volume — low; medium; hig...

  • Page 328

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 10 automatic high- beams auto highbeams on; off 11 flash lights with lock lights w/ lock on; off 12 auto lock doors auto lock doors on; off 13 auto unlock doors auto unlock doors on; off 14 sound horn wi...

  • Page 329

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 18 passive entry passive entry on; off 19 remote start com- fort system rmt start comfort on; off 20 easy exit seat easy exit seat on; off 21 key-off power delay power off delay off; 45 seconds; 5 minute...

  • Page 330

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 26 transport mode transport mode on; off 27 wheel alignment mode wheel alignment on; off 28 horn w/ remote lower horn w/ rmt lwr on; off 29 lights w/ remote lower lights w/ rmt lwr on; off 30 trailer sel...

  • Page 331

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 32 trailer name trailer name • trailer # (# is equal to slot position) • boat • car • cargo • dump • equipment • flatbed • gooseneck • horse • tag • motorcycle • snowmobile • travel • utility • 5th wheel...

  • Page 332

    Setting names setting names ab- breviated (left sub- menu layer) sub-menus (right submenu layer) 33 compass variance compass var 1-15 increments of 1 34 calibrate compass compass cal cancel; calibrate 35 fuel saver display fuel saver on; off turn menu off push and release the right arrow button to e...

  • Page 333

    Driver information display (did) the driver information display (did) features a driver- interactive display that is located in the instrument cluster. The did menu items consists of the following: • digital speedometer • vehicle info • fuel economy info • trip a • trip b • stop/start info (if equip...

  • Page 334

    The system allows the driver to select information by pushing the following buttons mounted on the steering wheel: • up arrow button push and release the up arrow button to scroll upward through the main menu and submenus. • down arrow button push and release the down arrow button to scroll downward...

  • Page 335

    • left arrow button push and release the left arrow button to return to the main menu from an info screen or submenu item. Driver information display (did) displays the did displays are located in the center portion of the cluster and consists of eight sections: 1. Main screen — the inner ring of th...

  • Page 336

    2. Audio / phone information and sub-menu informa- tion — whenever there are sub-menus available, the position within the sub-menus is shown here. 3. Selectable information (compass, temp, range to empty, trip a, trip b, average mpg, trailer trip (distance only), trailer brake gain) 4. Telltales/ind...

  • Page 337

    • unstored messages this message type is displayed indefinitely or until the condition that activated the message is cleared. Examples of this message type are “turn signal on” (if a turn signal is left on) and “lights on” (if driver leaves the vehicle). • unstored messages until run these messages ...

  • Page 338

    3. Push and release the right arrow button to access the ”oil life” screen. 4. Push and hold the right arrow button for one second to access the ”oil life reset” screen. 5. Push and release the down arrow button to select “yes”, then push and release the right arrow button to select reset of the oil...

  • Page 339

    • traction control off • washer fluid low • oil pressure low • oil change due • fuel low • service antilock brake system • service electronic throttle control • service power steering • cruise off • cruise ready • cruise set to xxx mph • tire pressure screen with low tire(s) “inflate tire to xx” • t...

  • Page 340

    • sound horn with remote lock: off; 1st press; 2nd press • vehicle not in park • key in ignition • key in ignition lights on • remote start active key to run • remote start active push start button • remote start aborted fuel low • remote start aborted too cold • remote start aborted door open • rem...

  • Page 341

    • transmission getting hot press brake • trans. Hot stop safely shift to park wait to cool • transmission cool ready to drive • trailer brake disconnected • service transmission • service shifter • engage park brake to prevent rolling • transmission too cold idle with engine on • washer fluid low • ...

  • Page 342

    • stop/start not ready – if equipped • stop/start not ready hood open – if equipped • stop/start not ready battery charging – if equipped • stop/start not ready trailer tow/haul selected – if equipped • stop/start not ready 4wd/low range selected – if equipped • stop/start not ready fuel level low –...

  • Page 343

    • stop/start to restart press clutch or shift to neutral – if equipped • stop/start req’d fault detected – if equipped • stop/start cannot autostart hood open – if equipped • stop/start unavailable service battery – if equipped • stop/start unavailable service stop/start system – if equipped • stop/...

  • Page 344

    • oil temperature warning light this telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. • charging system light this light shows the status of the electrical charg- ing system. If the light stays on or...

  • Page 345

    • engine temperature warning light this light warns of an overheated engine condi- tion. As temperatures rise and the gauge ap- proaches h, this indicator will illuminate and a single chime will sound after reaching a set threshold. Further overheating will cause the temperature gauge to pass h, a c...

  • Page 346

    • windshield washer fluid low indicator this telltale will turn on to indicate the wind- shield washer fluid is low. • low coolant level indicator this telltale will turn on to indicate the vehicle coolant level is low. • transmission temperature warning telltale this telltale indicates that the tra...

  • Page 347

    • air suspension payload protection telltale — if equipped this telltale will turn on to indicate that the maximum payload may have been exceeded or load leveling cannot be achieved at its current ride height. Protection mode will automatically be selected in order to “protect” the air suspension sy...

  • Page 348

    Did selectable menu items push and release the up or down arrow buttons until the desired selectable menu icon/title is highlighted in the did. Digital speedometer push and release the up or down arrow button until the digital display icon is high- lighted in the did. Push and release the right arro...

  • Page 349

    • if the tire pressure system requires service, “service tire pressure system” is displayed. • tire psi is an information only function and cannot be reset. • refer to the #tire pressure information system (tpis) under #starting and operating# for further informa- tion. • air suspension – if equippe...

  • Page 350

    Trip a push and release the up or down arrow button until the trip a icon/title is highlighted in the did. The trip a information will display the following: • distance mi or km • average mpg or l/100 km • average mph or km/h • elapsed time hold the right arrow button to reset all the informa- tion....

  • Page 351

    Stop/start – if equipped push and release the up or down arrow button until the stop/start icon is highlighted in the did. Push and release the right arrow button to display the stop/start status. Trailer tow push and release the up or down arrow button until the trailer tow icon is highlighted. Pus...

  • Page 352

    Screen setup push and release the up or down arrow button until the screen setup display icon is highlighted in the did. Push and release the right arrow button to enter the screen setup submenu. The screen setup feature allows you to change what information is displayed in the instrument cluster as...

  • Page 353

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 1 language select language english, spanish, french, italian, german, dutch 2 units units u.S.; metric 3 parksense parksense • notification — sound only; sound & display • front volume — low; medium; high • ...

  • Page 354

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 9 headlights on with wipers lights w/ wipers on; off 10 automatic highbeams auto highbeams on; off 11 flash lights with lock lights w/ lock on; off 12 auto lock doors auto lock doors on; off 13 auto unlock d...

  • Page 355

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 22 commercial settings commercial • aux switches • power take-off • pin setup 23 air suspension display alerts air susp. Alerts all; warnings only 24 aero ride height mode aero mode on; off 25 tire/jack mode...

  • Page 356

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 32 trailer name trailer name • trailer # (# is equal to slot position) • boat • car • cargo • dump • equipment • flatbed • gooseneck • horse • tag • motorcycle • snowmobile • travel • utility • 5th wheel 354...

  • Page 357

    Setting names setting names abbreviated (left submenu layer) sub-menus (right submenu layer) 33 compass variance compass var 1-15 increments of 1 34 calibrate compass compass cal cancel; calibrate 35 fuel saver display fuel saver on; off 36 park assist front chime vol- ume park assist front chime vo...

  • Page 358

    Uconnect® settings the uconnect® system uses a combination of buttons on the touchscreen and buttons on the faceplate located on the center of the instrument panel that allows you to access and change the customer programmable features. Many features can vary by vehicle. Uconnect® 5.0 buttons on tou...

  • Page 359

    Buttons on the faceplate buttons on the faceplate are located below the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side of the climate controls in the center of the instru- ment panel. Turn the control knob to scroll...

  • Page 360

    Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect® display. Customer programmable features — uconnect® 5.0 personal settings push the settings button on the faceplate to display the settings menu screen. In this mode the uconnect® system allows you to access progra...

  • Page 361

    Display after pressing the “display” button on the touchscreen the following settings will be available. • display mode when in this display you may select the auto or manual display settings. To change mode status, press and re- lease the “auto” or “manual” button on the touchscreen. Press the back...

  • Page 362

    Display” button on the touchscreen select from “on” or “off.” press the back arrow/done button on the touch- screen to return to the previous menu. Voice after pressing the “voice” button on the touchscreen the following settings will be available: • voice response length when in this display, you m...

  • Page 363

    Arrows above and below the current date to adjust. Press the back arrow/done button on the touchscreen to return to the previous menu. Safety/assistance after pressing the “safety/assistance” button on the touchscreen the following settings will be available: • parksense® the parksense® system will ...

  • Page 364

    Entire surroundings” across the top of the screen. After five seconds, this note will disappear. To make your selection, press the “parkview® backup camera active guidelines” button on the touchscreen and make your selection. Press arrow button on the touchscreen to return to the previous menu. • pa...

  • Page 365

    Lights after pressing the “lights” button on the touchscreen, the following settings will be available: • headlight off delay when this feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off. To change the headlight off delay setting...

  • Page 366

    • auto dim high beams — if equipped when this feature is selected, the high beam headlights will activate/deactivate automatically under certain con- ditions. To make your selection, press the “auto high beams” button on the touchscreen, and select from “on” or “off.” press the back arrow/done butto...

  • Page 367

    Or “off.” press the back arrow/done button on the touchscreen to return to the previous menu. • auto unlock on exit when this feature is selected, all doors will unlock when the vehicle is stopped, the transmission is in the park or neutral position and the driver’s door is opened. To make your sele...

  • Page 368

    • memory linked to fob — if equipped this feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. To make your selection, press the “memory linked to fob” button on the touchscreen and select from “on” or “off.” press the back arrow/done b...

  • Page 369

    Auto comfort systems — if equipped after pressing the “auto-on comfort” button on the touchscreen the following settings will be available: • auto-on driver heated/ventilated seat & steering wheel with vehicle start — if equipped when this feature is selected the driver’s heated seat and heated stee...

  • Page 370

    • engine off power delay when this feature is selected, the power window switches, radio, uconnect® phone system (if equipped), dvd video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to off. Opening either f...

  • Page 371

    • auto entry/exit suspension when this feature is selected, the vehicle automatically lowers from ride height position when vehicle shifted to park for easy entry/exit. To make your selection, press the “auto entry/exit” button on the touchscreen, select “on” or “off” followed by pressing the back a...

  • Page 372

    Trailer brake after pressing the “trailer brake” button on the touch- screen the following settings will be available: • trailer select when this feature is selected, the trailer type can be selected between “trailer 1,” “trailer 2,” “trailer 3” and “trailer 4.” • trailer brake type when this featur...

  • Page 373

    • speed adjusted volume this feature increases or decreases volume relative to vehicle speed. To change the speed adjusted volume press the “speed adjusted volume” button on the touch- screen and select from “off,” “1,” “2” or “3” buttons on the touchscreen. Press the back arrow/done button on the t...

  • Page 374

    Set, the compass will automatically compensate for the differences, and provide the most accurate compass heading. Note: keep magnetic materials away from the top of the instrument panel, such as ipod’s, mobile phones, lap- tops and radar detectors. This is where the compass module is located, and i...

  • Page 375

    By pressing the “on” button on the touchscreen and completing one or more 360-degree turns (in an area free from large metal or metallic objects). The compass will now function normally. Phone/bluetooth® after pressing the “phone/bluetooth” button on the touchscreen the following settings will be av...

  • Page 376

    Write down the sirius id numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online. Note: siriusxm travel link is a separate subscription and is available for u.S. Residents only. Restore settings after pressing the “restore setti...

  • Page 377

    System information after pressing the “system information” button on the touchscreen the following information will be available: • system information when system information is selected, a system informa- tion screen will appear displaying the system software version. Customer programmable features...

  • Page 378

    Note: all settings should be changed with the ignition in the “run” position. Display after pressing the “display” button on the touchscreen the following settings will be available. • display mode when in this display you may select one of the auto display settings. To change mode status, press and...

  • Page 379

    • set theme this feature will allow you to choose a background theme for the display screen. The theme will change the background color, highlight color, and button color of the display screen. Press the “set theme” button on the touchscreen and select one of the pre-configured themes available. • s...

  • Page 380

    • navigation turn-by-turn in cluster — if equipped when this feature is selected, the turn-by-turn directions will appear in the display as the vehicle approaches a designated turn within a programmed route. To make your selection, press the “navigation turn-by-turn in cluster” button on the touchsc...

  • Page 381

    • show command list when in this display, you may change the show com- mand list settings. To change the show command list settings, select from the “always,” “with help” or “never” buttons on the touchscreen until a check-mark appears next to the setting, showing that setting has been selected. Pre...

  • Page 382

    • time format this feature will allow you to select the time format display setting. Press the “time format” button on the touchscreen and select from “12hrs” or “24hrs.” press the back arrow button on the touchscreen to return to the previous menu. • show time in status bar — if equipped this featu...

  • Page 383

    Or “high” buttons on the touchscreen. Press the back arrow button on the touchscreen to return to the previous menu. Parksense® will retain its last known configura- tion state through ignition cycles. • rear parksense® chime volume the rear parksense® chime volume settings can be selected from the ...

  • Page 384

    On the touchscreen, until a check-mark appears next to the setting, indicating that the setting had been selected. Press the back arrow button on the touchscreen to return to the previous menu. • parkview® backup camera active guidelines your vehicle may be equipped with the parkview® rear back up c...

  • Page 385

    • hill start assist — if equipped when this feature is selected, the hill start assist (hsa) system is active. Refer to “electronic brake control system” in “starting and operating” for system function and operating information. To make your selection, press the “hill start assist” button on the tou...

  • Page 386

    • headlights with wipers — if equipped when this feature is selected, and the headlight switch is in the auto position, the headlights will turn on ap- proximately 10 seconds after the wipers are turned on. The headlights will also turn off when the wipers are turned off if they were turned on by th...

  • Page 387

    Doors & locks after pressing the “doors & locks” button on the touch- screen the following settings will be available: • auto door locks when this feature is selected, all doors will lock auto- matically when the vehicle reaches a speed of 15 mph (24 km/h). To make your selection, press the “auto do...

  • Page 388

    Press the “sound horn with lock” button on the touch- screen and select from “off”, “1st press” or “2nd press”. Press the back arrow button on the touchscreen to return to the previous menu. • sound horn with remote start when this feature is selected, the horn will sound when the remote start is ac...

  • Page 389

    • passive entry this feature allows you to lock and unlock the vehicles door(s) without having to push the remote keyless entry (rke) transmitter lock or unlock buttons. To make your selection, press the “passive entry” button on the touch- screen until a check-mark appears next to setting, show- in...

  • Page 390

    Button on the touchscreen, then select either “off,” “re- mote start” or “all starts”. Press the back arrow button on the touchscreen to return to the previous menu. Engine off options after pressing the “engine off options” button on the touchscreen the following settings will be available. • easy ...

  • Page 391

    Air suspension — if equipped after pressing the “suspension” button on the touch- screen the following settings will be available. • sound horn with lower when this feature is selected, a short horn sound will occur when the rke transmitter remote lower but- ton is pressed. Press the box next to you...

  • Page 392

    The feature showing the system has been activated or the check-mark is removed showing the system has been deactivated. • transport mode when this feature is selected the air suspension system is disabled to assist with flat bed towing. Press the box next to your selection and a check-mark appears n...

  • Page 393

    Until a check-mark appears next to the setting, showing that the setting has been selected. Refer to “integrated trailer brake module” in “starting and operating.” • trailer name when this feature is selected, the trailer name can be selected from 16 names. To make your selection, scroll up or down ...

  • Page 394

    • surround sound — if equipped this feature provides simulated surround sound mode. To make your selection, press the “surround sound” button on the touchscreen, select “on” or “off.” press the back arrow button on the touchscreen to return to the previous menu. • aux volume offset — if equipped thi...

  • Page 395

    Siriusxm setup — if equipped after pressing the “siriusxm setup” button on the touch- screen, the following settings will be available: • channel skip siriusxm can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scannin...

  • Page 396

    Settings to default?” select “ok” to restore, or “cancel” to exit. Once the settings are restored, a pop-up appears stating #settings reset to default.# clear personal data after pressing the “clear personal data settings” button on the touchscreen the following settings will be avail- able: • clear...

  • Page 397

    Ipod®/usb/mp3 control — if equipped located inside the center console upper lid, this feature allows an ipod® or external usb device to be plugged into the usb port. Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipo...

  • Page 398

    Steering wheel audio controls — if equipped the remote sound system controls are located on the back surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a pushbutton in the center. Pushing the top of the switch will increa...

  • Page 399

    Radio operation pushing the top of the switch will seek up for the next listenable station and pushing the bottom of the switch will seek down for the next listenable station. The button located in the center of the left hand control will tune to the next pre-set station that you have programmed in ...

  • Page 400

    Note: if you experience difficulty in playing a particular disc, it may be damaged (e.G., scratched, reflective coat- ing removed, a hair, moisture or dew on the disc) oversized, or have protection encoding. Try a known good disc before considering disc player service. Radio operation and mobile pho...

  • Page 401

    Situations or environments, such as aboard airplanes. If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio. This device complies with part 15 of the fcc rules and with industry canada license-exempt rss standard(s). Operation is subject ...

  • Page 402

    • consult the dealer or an experienced radio technician for help. Climate controls the climate control system allows you to regulate the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel below the radio. Manual climate cont...

  • Page 403

    Front blower control there are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the off position. Temperature control use this control to regulate the tem- perature o...

  • Page 404

    Note: a/c cannot be deselected when in max a/c position. The led will blink three times if the a/c button is pushed. If your air conditioning performance seems lower than expected, check the front of the a/c condenser (located in front of the radiator), for an accu- mulation of dirt or insects. Clea...

  • Page 405

    Floor mode air is directed through the floor outlets with a small amount through the defrost and side win- dow demist outlets. Mix mode air is directed through the floor, defrost and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat at the windsh...

  • Page 406

    Note: • if the recirculation button is pushed when the system is in defrost mode, the recirculation led indicator will flash three times and then turn off to indicate recirculation mode is not allowed. • continuous use of the recirculation mode may make the inside air stuffy and window fogging may o...

  • Page 407

    Manual climate controls with touchscreen — if equipped buttons on the faceplate the buttons on the faceplate are located below the radio touchscreen. Buttons on the touchscreen buttons on the touchscreen are accessible on the radio. Climate controls — buttons on the faceplate temperature controls — ...

  • Page 408

    Button descriptions (applies to both buttons on the faceplate and buttons on the touchscreen) 1. Max a/c button press and release to toggle between max a/c and the prior settings. The button on the touchscreen illuminates when max a/c is on. In max a/c, the blower level and mode position can be adju...

  • Page 409

    Equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after 10 minutes. Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abra...

  • Page 410

    Note: bi-level mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. • floor mode air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • mix mode air come...

  • Page 411

    8. Climate control off button press and release this button to turn the climate control on/off. 9. Temperature control down button push the button on the faceplate for cooler temperature settings. On the touchscreen, slide the temperature bar towards the blue arrow button for cooler temperature sett...

  • Page 412

    Automatic climate controls with touchscreen — if equipped buttons on the faceplate the buttons on the faceplate are located below the uconnect® screen. Caution! Do not attach any object to touchscreen, doing so can result in damage to the touchscreen. Automatic climate controls — buttons on the face...

  • Page 413

    Buttons on the touchscreen buttons on the touchscreen are accessible on the uconnect® system screen. Button descriptions (applies to both buttons on the faceplate and buttons on the touchscreen) 1. Max a/c button press and release to change the current setting, the indicator illuminates when max a/c...

  • Page 414

    This function again will cause the max a/c operation to switch into manual mode and the max a/c indicator will turn off. 2. A/c button press and release to change the current setting, the indicator illuminates when a/c is on. Performing this function again will cause the a/c operation to switch into...

  • Page 415

    Caution! Failure to follow these cautions can cause damage to the heating elements: • use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements....

  • Page 416

    When this feature is enabled. Sync is used to synchronize the passenger temperature setting with the driver tem- perature setting. Changing the passenger temperature setting while in sync will automatically exit this feature. 10. Blower control blower control is used to regulate the amount of air fo...

  • Page 417

    • bi-level mode air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demis- ter outlets. Note: bi-level mode is designed under comfort con- ditions to provide cooler air out of the panel outlets and warmer air from the ...

  • Page 418

    Temperature settings or on the touchscreen, press and slide the temperature bar towards the red arrow for warmer temperature settings. Note: in sync mode, this button will also automatically adjust the passenger temperature setting at the same time. 15. Temperature control (uconnect® 5.0) press the ...

  • Page 419

    Behind the radiator and through the condenser. Fabric front fascia protectors may reduce airflow to the condenser, reducing air conditioning performance. Max a/c max a/c sets the control for maximum cooling perfor- mance. Press and release to toggle between max a/c and the prior settings. The button...

  • Page 420

    Note: in cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (button on the touchscreen greyed out) if conditions exist that could create fogging on the inside of the windshield. On systems with manual climate controls, the recir...

  • Page 421

    To provide you with maximum comfort in the automatic mode, during cold start-ups the blower fan will remain on low until the engine warms up. The blower will increase in speed and transition into auto mode. Manual operation override the system allows for manual selection of blower speed, air distrib...

  • Page 422

    Winter operation to ensure the best possible heater and defroster perfor- mance, make sure the engine cooling system is functioning properly and the proper amount, type, and concentration of coolant is used. Refer to “maintenance procedures” in “maintaining your vehicle” for proper coolant selection...

  • Page 423

    Control setting suggestions for various weather conditions operating tips chart 4 understanding your instrument panel 421.

  • Page 424

    Uconnect® voice recognition introducing uconnect® start using uconnect® voice recognition with these helpful quick tips. It provides the key voice commands and tips you need to know to control your uconnect® 5.0 or 8.4a/8.4an system. Key features: • 5” touchscreen • three buttons on either side of t...

  • Page 425

    If you see the icon on your touchscreen, you have the uconnect® 8.4an system. If not, you have a uconnect® 8.4a system. Get started 1. Visit uconnectphone.Com to check mobile device and feature compatibility and to find phone pairing instructions. 2. Reduce background noise. Wind and passenger con- ...

  • Page 426

    Two buttons are all you need to control your uconnect® system with your voice. Basic voice commands the basic voice commands below can be given at any point while using your uconnect® system. Push the vr button . After the beep, say$ • cancel to stop a current voice session • help to hear a list of ...

  • Page 427

    Uconnect® 5.0 uconnect® 8.4a/8.4an 4 understanding your instrument panel 425.

  • Page 428

    Radio use your voice to quickly get to the am, fm or siriusxm satellite radio® stations you would like to hear. (sub- scription or included siriusxm satellite radio® trial required.) push the vr button . After the beep, say$ • tune to ninety-five-point-five fm • tune to satellite channel hits 1 tip:...

  • Page 429

    Media uconnect® offers connections via usb, sd, bluetooth® and auxiliary ports (if equipped). Voice operation is only available for connected usb and ipod® devices. (remote cd player optional and not available on all vehicles.) push the vr button . After the beep, say one of the following commands a...

  • Page 430

    Tip: press the browse button on the touchscreen to see all of the music on your ipod® or usb device. Your voice command must match exactly how the artist, album, song and genre information is displayed. Uconnect® 5.0 media uconnect® 8.4a/8.4an media 428 understanding your instrument panel.

  • Page 431

    Climate (8.4a/8.4an) too hot? Too cold? Adjust vehicle temperatures hands- free and keep everyone comfortable while you keep moving ahead. (if vehicle is equipped with climate control.) push the vr button . After the beep, say one of the following commands: • set driver temperature to 70 degrees • s...

  • Page 432

    Navigation (8.4a/8.4an) the uconnect® navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (navigation is optional on the uconnect® 8.4a system. See your dealer to activate navigation at any time.) 1. To enter a destination, push...

  • Page 433

    Phone making and answering hands-free phone calls is easy with uconnect®. When the phonebook button is illumi- nated on your touchscreen, your system is ready. Check uconnectphone.Com for mobile phone compatibility and pairing instructions. Push the phone button . After the beep, say one of the foll...

  • Page 434

    Voice text reply uconnect® will announce incoming text messages. Push the phone button and say listen. (must have com- patible mobile phone paired to uconnect® system.) 1. Once an incoming text message is read to you, push the phone button . After the beep, say: “reply.” 2. Listen to the uconnect® p...

  • Page 435

    Tip: your mobile phone must have the full implementa- tion of the message access profile (map) to take advan- tage of this feature. For details about map, visit uconnectphone.Com. Apple iphone® ios6 or later supports reading incoming text messages only. Uconnect® access* (8.4a/8.4an) an included tri...

  • Page 436

    Register (8.4a/8.4an) 1. Press the apps button on the bottom of the 8.4-inch touchscreen. 2. If a pop-up message appears, press register or go to the favorite apps menu and press uconnect® regis- tration . 3. Read through the registration instructions. Enter and confirm your personal email address. ...

  • Page 437

    Mobile app (8.4a/8.4an) securely link your mobile device to your vehicle with the uconnect® access app. Once you have downloaded the app, you may start your vehicle or lock it from virtually any distance. (vehicle must be properly equipped with factory-installed remote start.) download the uconnect®...

  • Page 438

    Voice texting (8.4a/8.4an) 1. To send a message, push the phone button . After the beep, say the following command: “send mes- sage to john smith.” 2. Listen to the prompt. After the beep, dictate the message you would like to send. Wait for uconnect® to process your message. 3. The uconnect® system...

  • Page 439

    4. Once the yelp® home screen appears on the touch- screen, push the vr button , then say: “yelp search.” 5. Listen to the system prompts and after the beep, tell uconnect® the place or business that you’d like uconnect® to find. Tip: once you perform a search, you can reorganize the results by sele...

  • Page 440

    Siriusxm travel link™ (8.4a/8.4an) need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? Siriusxm travel link™ is a suite of services that brings a wealth of information right to your uconnect® 8.4an system. (not available for 8.4a system.) push...

  • Page 441

    Additional information © 2014 chrysler group llc. All rights reserved. Mopar and uconnect are registered trademarks and mopar owner connect is a trademark of chrysler group llc. Android is a trademark of google inc. Siriusxm and all related marks and logos are trademarks of siriusxm radio inc. Yelp,...

  • Page 443: Starting And Operating

    Starting and operating contents ! Starting procedures . . . . . . . . . . . . . . . .448 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .448 ▫ automatic transmission . . . . . . . . . . . . . . . .449 ▫ keyless enter-n-go™ . . . . . . . . . . . . . . . . . .449 ▫ normal starting. . . ....

  • Page 444

    ▫ brake/transmission shift interlock system . . .461 ▫ eight-speed automatic transmission — if equipped . . . . . . . . . . . . . . . . . . . . . . . . .461 ▫ six-speed automatic transmission — 1500 models only (if equipped) . . . . . . . . . . .470 ▫ six-speed automatic transmission — 2500/3500 mod...

  • Page 445

    ▫ electronic vehicle information center (evic)/driver information display (did) display messages . . . . . . . . . . . . . . . . . . . . .527 ▫ operation . . . . . . . . . . . . . . . . . . . . . . . . . . .528 ! Axle locker system — power wagon models only (if equipped) . . . . . . . . . . . .528 !...

  • Page 446

    ▫ after driving off-road . . . . . . . . . . . . . . . . .555 ! Winch usage — power wagon only — (if equipped) . . . . . . . . . . . . . . . . . . . . . . . .556 ▫ things to know before using your winch. . . .556 ▫ understanding the features of your winch. . .558 ▫ winch accessories . . . . . . . . ...

  • Page 447

    ▫ tire identification number (tin). . . . . . . . . . .600 ▫ tire terminology and definitions . . . . . . . . . .602 ▫ tire loading and tire pressure . . . . . . . . . . .603 ! Tires — general information . . . . . . . .608 ▫ tire pressure . . . . . . . . . . . . . . . . . . . . . . . .608 ▫ tire in...

  • Page 448

    ▫ 3.6l engine . . . . . . . . . . . . . . . . . . . . . . . . . .634 ▫ 5.7l/6.4l engines . . . . . . . . . . . . . . . . . . . . .635 ▫ reformulated gasoline . . . . . . . . . . . . . . . . .635 ▫ gasoline/oxygenate blends . . . . . . . . . . . . . .636 ▫ e-85 usage in non-flex fuel vehicles . . . ....

  • Page 449

    ▫ trailer hitch type and maximum trailer weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . .656 ▫ trailer towing weights (maximum trailer weight ratings) . . . . . . . . . . . . . . . . . . . . . .657 ▫ trailer and tongue weight . . . . . . . . . . . . . .657 ▫ towing requirements . . ....

  • Page 450

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. The starter should not be operated for more than 10- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Warnin...

  • Page 451

    Automatic transmission start the engine with the transmission in park position. Apply the brake before shifting into any driving range. Note: • this vehicle is equipped with a transmission shift interlocking system. The brake pedal must be pressed to shift out of park. • if equipped with an 8 speed ...

  • Page 452

    4. If you wish to stop the cranking of the engine prior to the engine starting, push the button again. Note: normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. To turn off the engine using engine start/stop button 1. Place the shift lever...

  • Page 453

    Engine start/stop button functions — with driver’s foot off the brake pedal (in park or neutral position) the engine start/stop button operates similar to an ignition switch. It has three positions, off, acc, run. To change the ignition switch positions without starting the vehicle and use the acces...

  • Page 454

    Warning! • never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. • do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic tr...

  • Page 455

    Stop/start system — if equipped the stop/start function is developed to save fuel and reduce emissions. The system will stop the engine auto- matically during a vehicle stop if the required conditions are met. Releasing the brake pedal will automatically re-start the vehicle. Automatic mode the stop...

  • Page 456

    Possible reasons the engine does not autostop prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled. In following situations the engine will not stop: • driver’s seat belt is not buckled • driver’s door is not closed • outside temperature is...

  • Page 457

    To start the engine while in autostop mode while in drive the engine will start when the brake pedal is released or the throttle pedal is depressed. The transmission will automatically reengage upon engine restart. During this transition the brakes will hold the vehicle to avoid undesired vehicle mo...

  • Page 458

    The engine may then be restarted by moving the trans- mission shift selector out of park (e.G. To drive) or, in some cases, only by a key start. The electronic vehicle information center (evic)/driver information display (did) will display a shift out of park message, or a stop/start key start requi...

  • Page 459

    2. The stop/start off message will appear in elec- tronic vehicle information center (evic)/driver in- formation display (did). Refer to “electronic vehicle information center (evic) or driver information dis- play (did)” in “understanding your instrument panel” for further information. 3. At the ne...

  • Page 460

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. 1500 models the engine block heater cord is routed under the hood on th...

  • Page 461

    Automatic transmission caution! Damage to the transmission may occur if the follow- ing precautions are not observed: • shift into or out of park or reverse only after the vehicle has come to a complete stop. • do not shift between park, reverse, neu- tral, or drive when the engine is above idle spe...

  • Page 462

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 463

    Key ignition park interlock this vehicle is equipped with a key ignition park inter- lock which requires the transmission to be in park before the ignition switch can be turned to the lock/ off (key removal) position. The key fob can only be removed from the ignition when the ignition is in the lock...

  • Page 464

    Speeds (refer to #brake/transmission shift interlock sys- tem# in this section). To shift past multiple gear ranges at once (such as park to drive), simply rotate the gear selector to the appropriate detent. Select the drive range for normal driving. The electronically-controlled transmission provid...

  • Page 465

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 466

    Warning! (continued) • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something....

  • Page 467

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 468

    Reverse (r) this range is for moving the vehicle backward. Shift into reverse only after the vehicle has come to a complete stop. Neutral (n) use this range when the vehicle is standing for prolonged periods with the engine running. Apply the parking brake and shift the transmission into park if you...

  • Page 469

    When frequent transmission shifting occurs (such as when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, or while towing heavy trailers), select tow/haul mode or use the electronic range select (ers) shift control (refer to #electronic rang...

  • Page 470

    2. Shift the transmission into park, if possible. If not, shift the transmission to neutral. 3. Push and hold the ignition switch until the engine turns off. 4. Wait approximately 30 seconds. 5. Restart the engine. 6. Shift into the desired gear range. If the problem is no longer detected, the trans...

  • Page 471

    To exit ers mode, simply press and hold the gear+ switch until “d” is once again displayed in the instru- ment cluster. Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal in...

  • Page 472

    The “tow/haul indicator light” will illuminate in the instrument cluster to indicate that tow/haul mode has been activated. Pressing the switch a second time restores normal operation. Normal operation is always the default at engine start-up. If tow/haul mode is desired, the switch must be pressed ...

  • Page 473

    Only shift from drive to park or reverse when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. The transmission shift lever has only park, reverse, neutral, and drive shift positions. Manual down- shifts can...

  • Page 474

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • your vehicle could move and injure you and others if it is not completely in park. Check by trying to mo...

  • Page 475

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park, turn the engine off, and r...

  • Page 476

    Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to the on/run position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • do not race the engine when shifting from park or neutral into another gear ...

  • Page 477

    Warning! Do not coast in neutral and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. Caution! Towing the vehicle, coasting, or driving for any oth...

  • Page 478

    Select (ers) operation” in this section for further infor- mation) to select a lower gear range. Under these condi- tions, using a lower gear range will improve performance and extend transmission life by reducing excessive shift- ing and heat buildup. If the transmission temperature exceeds normal ...

  • Page 479

    Direct gears only. Normal operation will resume once the transmission temperature has risen to a suitable level. Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transmission li...

  • Page 480

    Electronic range select (ers) operation — six-speed transmission (1500 models only) the electronic range select (ers) shift control allows the driver to limit the highest available gear when the transmission is in drive. For example, if you shift the transmission into 4 (fourth gear), the transmissi...

  • Page 481

    To exit ers mode, simply hold the shift lever to the right (+) (console shift) or press and hold the ers (+) switch (column shift) until “d” is once again displayed in the instrument cluster. Column shift lever console shift lever 5 starting and operating 479.

  • Page 482

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Note: to select the proper gear position for maximum deceleration (engine braking), simply press and hold the shif...

  • Page 483

    When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the tow/haul switch to activate tow/ haul mode. This will improve performance and reduce the potential for transmission overheating or failure due ...

  • Page 484

    Warning! Do not use the “tow/haul” feature when driving in icy or slippery conditions. The increased engine braking can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possi- bly resulting in personal injury or de...

  • Page 485

    Cause damage to the transmission. The torque con- verter will refill within five seconds after starting the engine. Six-speed automatic transmission — 2500/3500 models only the transmission gear position display (located in the instrument cluster) indicates the transmission gear range. The shift lev...

  • Page 486

    Gear ranges do not race the engine when shifting from park or neutral into another gear range. Note: after selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. Park (p) this range supplements the parki...

  • Page 487

    Warning! (continued) • your vehicle could move and injure you and others if it is not completely in park. Check by trying to move the shift lever out of park with the brake pedal released. Make sure the transmission is in park before leaving the vehicle. • it is dangerous to shift out of park or neu...

  • Page 488

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 489

    • release the shift lever and make sure it is fully seated in the park gate. • look at the transmission gear position display and verify that it indicates the park position. • with brake pedal released, verify that the shift lever will not move out of park. Reverse (r) this range is for moving the v...

  • Page 490

    Drive (d) this range should be used for most city and highway driving. It provides the smoothest upshifts and down- shifts, and the best fuel economy. The transmission automatically upshifts through underdrive first, second, and third gears, direct fourth gear and overdrive fifth and sixth gears. Th...

  • Page 491

    During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. This feature im- proves warm up time of the engine and transmission to achieve maximum efficiency. Engagement of both the torque converter clutch and the top ov...

  • Page 492

    Note: even if the transmission can be reset, we recom- mend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnos- tic equipment to determine if the problem could recur. If the transmission cannot be reset, authorized dealer service is requir...

  • Page 493

    Warning! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Note: to select the proper gear position for maximum deceleration (engine braking), simply press and hold the ers ...

  • Page 494

    When to use tow/haul mode when driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the tow/haul switch to activate tow/ haul mode. This will improve performance and reduce the potential for transmission overheating or failure due ...

  • Page 495

    Warning! Do not use the “tow/haul” feature when driving in icy or slippery conditions. The increased engine braking can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possi- bly resulting in personal injury or de...

  • Page 496

    Four-wheel drive operation — if equipped four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the operating instructions for your transfer case, located in this section for further informa- tion. Manually shifted trans...

  • Page 497

    When operating your vehicle in 4l, the engine speed is approximately three times that of the 2h or 4h positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circ...

  • Page 498

    For additional information on the appropriate use of each transfer case mode position, see the information below: 2h rear-wheel drive high range — this range is for normal street and highway driving on dry hard surfaced roads. 4h four-wheel drive high range — this range locks the front and rear driv...

  • Page 499

    Vehicle in motion, the transfer case will engage/ disengage faster if you momentarily release the accelera- tor pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2h or 4h to 4l with the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift the transmission ...

  • Page 500

    Electronically shifted transfer case (four-position switch) — if equipped this is an electronic shift transfer case and is operated by the 4wd control switch (transfer case switch), which is located on the instrument panel. This electronically shifted transfer case provides four mode positions: • tw...

  • Page 501

    And 4wd low positions are designed for loose, slippery road surfaces only. Driving in the 4wd lock and 4wd low positions on dry hard surfaced roads may cause increased tire wear and damage to the driveline compo- nents. Note: the transfer case neutral position is selected by pressing the button loca...

  • Page 502

    Note: before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five seconds, and retry selection. To find the shift require- ments, refer to...

  • Page 503

    Warning! You or others could be injured or killed if you leave the vehicle unattended with the transfer case in the neutral position without first fully engaging the parking brake. The transfer case neutral position disengages both the front and rear drive shafts from the powertrain and will allow t...

  • Page 504

    Shifting procedure note: • if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The position indicator light for the previous posi- tion will remain on and the newly selected position indicator light will continue to flash until all t...

  • Page 505

    2wd or 4wd lock to 4wd low note: when shifting into or out of 4wd low some gear noise may be heard. This noise is normal and is not detrimental to the vehicle or occupants. Shifting can be performed with the vehicle rolling 2 to 3 mph (3 to 5 km/h) or completely stopped. You can use either of the fo...

  • Page 506

    • the ignition switch must be in the on position for a shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the on position, the shift will not take place and no position indicator lights will be on or flashing. Electronically shifted transfer ca...

  • Page 507

    • four-wheel drive low range (4wd low) • neutral (neutral) this electronically shifted transfer case is designed to be driven in the two–wheel drive position (2wd) or four - wheel drive position (4wd auto) for normal street and highway conditions on dry hard surfaced roads). Driving the vehicle in 2...

  • Page 508

    Transfer case position indicator lights the transfer case position indicator lights (4wd, 4low, and 4wd auto) are located in the instrument cluster and indicate the current and desired transfer case selection. When you select a different transfer case posi- tion, the indicator lights will do the fol...

  • Page 509

    Warning! Always engage the parking brake when powering down the vehicle if the “svc 4wd warning light” is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury or death. Note: do not attempt to make a shift while only the front or rear wheels are s...

  • Page 510

    For additional information on the appropriate use of each transfer case mode position, see the information below: 2wd rear-wheel drive high range - this range is for normal street and highway driving on dry hard surfaced roads. 4wd auto four-wheel drive auto range - this range sends power to the rea...

  • Page 511

    Shifting procedure note: • if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The position indicator light for the previous posi- tion will remain on and the newly selected position indicator light will continue to flash until all t...

  • Page 512

    This electronically shifted transfer case provides five mode positions: • two-wheel drive high range (2wd) • four-wheel drive automatic range (4wd auto) • four-wheel drive lock range (4wd lock) • four-wheel drive low range (4wd low) • neutral (neutral) this electronically shifted transfer case is de...

  • Page 513

    Note: the transfer case neutral position is selected by depressing the recessed button (with a ballpoint pen or similar object) located in the center of the 4wd control switch. The transfer case neutral position is to be used for recreational towing only. Refer to “recreational towing” in “starting ...

  • Page 514

    After engine start up or illuminates during driving, it means that the four-wheel drive system is not function- ing properly and that service is required. Warning! Always engage the parking brake when powering down the vehicle if the “svc 4wd warning light” is illuminated. Not engaging the parking b...

  • Page 515

    Warning! (continued) disengages both the front and rear drive shafts from the powertrain and will allow the vehicle to move regardless of the transmission position. The parking brake should always be applied when the driver is not in the vehicle. For additional information on the appropriate use of ...

  • Page 516

    Shifting procedure note: • if any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The position indicator light for the previous position will remain on and the newly selected posi- tion indicator light will continue to flash until all t...

  • Page 517

    Preferred procedure 1. With the engine running, slow the vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into neutral. 3. While still rolling, press the desired position on the transfer case control switch. 4. After the desired position indicator light is on (not flashing), shift the ...

  • Page 518

    Air suspension system (1500 models) — if equipped description the air suspension system provides full time load level- ing capability along with the benefit of being able to adjust vehicle height by the push of a button. 1 — up button 2 — down button 3 — entry/exit mode indicator (customer selectabl...

  • Page 519

    Note: the vehicle will automatically enter aero mode when the vehicle speed remains between 62 mph (100 km/h) and 66 mph (106 km/h) for greater than 20 seconds or if the vehicle speed exceeds 66 mph (106 km/h). • normal ride height (nrh) – this is the standard position of the suspension and is meant...

  • Page 520

    • if the vehicle is in offroad1 or offroad2 setting, be aware of your surroundings, you may not have the clearance required for certain areas and vehicle dam- age may occur. • aero mode (lowers the vehicle approximately .6 in [15 mm]) – this position provides improved aerody- namics by lowering the ...

  • Page 521

    (24 km/h) and 25 mph (40 km/h) for greater than 60 seconds, or the vehicle speed exceeds 25 mph (40 km/h) the entry/exit change will be cancelled. To return to normal height mode, press the “up” button once while in entry/exit or drive the vehicle over 15 mph (24 km/h). Entry/exit mode may not be av...

  • Page 522

    To be disabled. Refer to “electronic vehicle information center (evic) or driver information display (did)” in “understanding your instrument panel” for further in- formation. Note: if equipped with a touch screen radio all enabling/disabling of air suspension features must be done through the radio...

  • Page 523

    Transport mode to assist with flat bed towing, the air suspension system has a feature which will put the vehicle into entry/exit height and disable the automatic load leveling system. Refer to “electronic vehicle information center (evic) or driver information display (did)” in “understanding your ...

  • Page 524

    Electronic vehicle information center (evic)/driver information display (did) display messages when the appropriate conditions exist, a message will appear in the evic/did display. Refer to “electronic vehicle information center (evic) or driver information display (did)” in “understanding your inst...

  • Page 525

    The indicator lamps 3 through 6 will illuminate to show the current position of the vehicle. Flashing indicator lamps will show a position which the system is working to achieve. When raising, if multiple indicator lamps are flashing, the highest flashing indicator lamp is the posi- tion the system ...

  • Page 526

    • entry/exit mode – indicator lamp 3 will be illumi- nated when the vehicle is in entry exit mode. Entry/ exit mode can be requested up to 33 mph (53 km/h). If vehicle speed is reduced to, and kept below, 15 mph (24 km/h) indicator lamp 4 will flash and indicator lamp 3 will remain solid until entry...

  • Page 527

    Normal ride height (nrh) – this is the standard position of the suspension and is meant for normal driving. Trailer mode (lowers the vehicle approximately 1 in (25 mm) – this position will lower the rear suspension and provide load leveling for all loading conditions including towing a trailer. Afte...

  • Page 528

    Warning! The air suspension system uses a high pressure volume of air to operate the system. To avoid per- sonal injury or damage to the system, see your authorized dealer for service. Air suspension modes the air suspension system has multiple modes to protect the system in unique situations: tire/...

  • Page 529

    Wheel alignment mode before performing a wheel alignment this mode must be enabled. Refer to “electronic vehicle information center (evic) or driver information display (did)” in “under- standing your instrument panel” or “uconnect® set- tings” in “understanding your instrument panel” if equipped wi...

  • Page 530

    Operation pushing the trailer mode button once, while at normal ride height (nrh) will lower the vehicle to trailer level. Note: the led will continuously blink until vehicle trailer level that been achieved. Pushing the trailer mode again will raise the vehicle to normal ride height (nrh). Note: th...

  • Page 531

    Caution! • do not lock the front or rear axle on hard surfaced roads. The ability to steer the vehicle is reduced and damage to the drivetrain may occur when the axles are locked on hard surfaced roads. • do not try to lock the rear axle if the vehicle is stuck and the tires are spinning. You can da...

  • Page 532

    Note: left to right wheel speed difference may be necessary to allow the axle to fully lock. If the indicator light is flashing after placing the switch in the rear lock or front/rear lock position, drive the ve- hicle in a turn or on loose gravel to expedite the locking action. Warning! Do not use ...

  • Page 533

    Stabilizer/sway bar system — power wagon only your vehicle is equipped with an electronic disconnecting stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. Due to the use of taller springs, this vehicle has an increased ride height of approximately 1.9 in ...

  • Page 534

    Warning! Do not disconnect the stabilizer bar and drive on hard surfaced roads or at speeds above 18 mph (29 km/h), you may lose control of the vehicle, which could result in serious injury or death. The front stabilizer bar enhances vehicle stability and is nec- essary for maintaining control of th...

  • Page 535

    Warning! (continued) attempt to drive the vehicle over 18 mph (29 km/h). Driving faster than 18 mph (29 km/h) may cause loss of control of the vehicle, which could result in serious injury or death. Contact your local service center for assistance. Safe off-road driving — power wagon only off-road d...

  • Page 536

    Has an rti of 510, which means you can articulate one front wheel 26 inches in the air while the other three wheels remain in contact with the ground. Water fording characteristics water fording characteristic is the vehicle’s ability to cross a body of still water, where the powertrain and drivetra...

  • Page 537

    Accelerations, turns or braking. In most cases there are no road signs, posted speed limits or signal lights. Therefore you will need to use your own good judgment on what is safe and what isn’t. When on a trail you should always be looking ahead for surface obstacles and changes in terrain. The key...

  • Page 538

    • snow – in heavy snow or for additional control and traction at slower speeds, shift the transmission to a low gear and shift the transfer case to 4l (low range) if necessary. Do not shift to a lower gear than necessary to maintain headway. Over-revving the engine can spin the wheels and traction w...

  • Page 539

    Surface area. Reduced tire pressure will drastically improve your traction and handling, while driving on the soft sand, but you must return the tires to normal air pressure before driving on pavement or other hard surfaces. Be sure you have a way to air the tires back up prior to reducing the press...

  • Page 540

    Using a spotter there are many times where it is hard to see the obstacle or determine the correct path. Determining the correct path can be extremely difficult when you are confronting many obstacles. In these cases have someone guide you over, through, or around the obstacle. Have the person stand...

  • Page 541

    You should now be able to drive out following the trench you just created at a 45-degree angle. Warning! There is an increased risk of rollover when crossing an obstacle, at any angle, with steep sides. Crossing logs to cross a log, approach it at a slight angle (approxi- mately 10 to 15 degrees). T...

  • Page 542

    Caution! Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Hill climbing hill climbing requires good judgment and a good under- standing of your abilities and your vehicle’s limitations. Hills can cause serious problems. Some are just too steep to climb and sho...

  • Page 543

    Fresh #bite# into the surface and will usually provide enough traction to complete the climb. If you do not make it to the top, place the vehicle in reverse and back straight down the grade using engine resistance along with the vehicle brakes. Warning! Never attempt to climb a hill at an angle or t...

  • Page 544

    Soils. If possible transverse the incline at an angle heading slightly up or down. Warning! Driving across an incline increases the risk of a rollover , which may result in severe injury. • if you stall or begin to lose headway – if you stall or begin to lose headway while climbing a steep hill, all...

  • Page 545

    Something goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested water into the engine air intake. If the engine stalls do not attempt to restart it. Determine if it has ingested water first. The key to any crossing is low and slow. You want to use first...

  • Page 546

    • crossing puddles, pools, flooded areas or other standing water – puddles, pools, flooded or other standing water areas normally contain murky or muddy waters. These water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach angle, and bottom ...

  • Page 547

    Warning! Never drive through fast moving deep water. It can push your vehicle downstream, sweeping it out of control. This could put you and your passengers at risk of injury or drowning. Airing down for off-road driving running lower tire pressure off-road can improve your ride comfort and vehicle ...

  • Page 548

    Off-road driving without the ability to recover your vehicle from a situation. Having another vehicle with you usually works best for most situations. The first thing to do is assess the situation. Why are you stuck? Are you hung up on something? Would it be easier to go forward or to go backward? C...

  • Page 549

    This process to clean the debris from the tread and improve the traction. You want to create a rocking motion with the vehicle. This helps build vehicle momentum, which hopefully gets you out. Remember to ease off and on the accelerator before and after the shift. If after a few rock cycles your veh...

  • Page 550

    Vehicle becomes free, the driver of the previously stuck vehicle should signal they are free and should hit their brakes stopping both vehicles. The driver of the pull- ing vehicle should let off the throttle without using the brakes, once signaled by the other driver. This se- quence is important t...

  • Page 551

    Within reach try using your spare tire by burying it. Once you have determined an anchor point hook up the cable, ensuring there are a least five wraps of cable left on the drum, and place a floor mat or something else over the strung out cable. Placing something over the strung out cable helps keep...

  • Page 552

    • inspect the radiator for mud and debris and clean as required. • check threaded fasteners for looseness, particularly on the chassis, drivetrain components, steering, and sus- pension. Retighten them, if required, and torque to the values specified in the service manual. • check for accumulations ...

  • Page 553

    Limited-slip differential the limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-...

  • Page 554

    When there is a difference in the surface traction under the rear (driving) wheels. Warning! Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the rear wheels. You could lose control of the vehicle and possibly have a collision. Accelerate slowly and ...

  • Page 555

    Driving through water driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. Flowing/rising water warning! Do not drive on or across a road or path where water is flowing and/or rising (as in storm run-off). Flow...

  • Page 556

    Caution! • always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • determine the condition of the road or the path that is under water and if there are any obstacles in the wa...

  • Page 557

    Off-road driving tips care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope. If natural obstacles force you to travel diagonally up or down a hill, choose a mild angle and keep as little side tilt as possible. Keep the vehicle moving and make turns sl...

  • Page 558

    • after extended operation in mud, sand, water, or similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. Warning! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking. ...

  • Page 559

    2. Attach the hook to a suitable anchor point. Caution! Be certain the anchor will withstand the load re- quired to tension the wire rope. 3. Apply at least 500 lbs (227 kg) of tension to the rope while winding the rope. Always use care to ensure the rope does not pile up on one side of the drum and...

  • Page 560

    Understanding the features of your winch winch components 558 starting and operating.

  • Page 561

    1. Motor: the winch motor is powered by the vehicle charging system and features a thermal protection switch that automatically stops motor function in the power-in direction if the motor gets too hot. 2. Remote socket: the remote socket allows the remote control to be attached to the control pack t...

  • Page 562

    Winch accessories the following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: wire rope, through use, will develop #barbs# which can slice skin. It is ex- tremely important to wear pro- tective gloves while operating the winch or h...

  • Page 563

    Tree trunk protector: typi- cally made of tough, high- quality nylon, it provides the operator an attachment point for the winch rope to a wide variety of anchor points and objects, as well as protect liv- ing trees. Operating your winch warning! Failure to observe any of these warnings regarding pr...

  • Page 564

    Warning! (continued) • never wrap wire rope back onto itself. Always use a choker chain, wire choker rope or tree trunk protector on the anchor. • never attach a recovery strap to the winch hook to increase the length of a pull. • never attempt to tow a vehicle with the recovery strap attached direc...

  • Page 565

    • always wear leather gloves and do not allow the wire rope to slip through your hands when handling the rope. • only the operator should handle the wire rope and remote control. • think safety at all times. Vehicle recovery using the winch caution! • always know your winch: take the time to fully r...

  • Page 566

    1. Inspect the winch, winch mount, and wire rope for damage. Do not use the winch if the mount is loose or rope shows excessive wear or damage. 2. Put on gloves. 3. Disengage the clutch to allow free spooling of the winch drum, rotate the clutch lever on the winch to disengage. Freespooling conserve...

  • Page 567

    4. Free the winch hook and attach the hook strap. Free the winch hook from its anchor point. Attach the hook strap to the hook (if not attached). 5. Pull the wire to the anchor point. Pull out enough wire rope to reach your anchor point. Be sure to keep a certain amount of tension on the wire as it ...

  • Page 568

    6. Secure to the anchor point. Once you have established your anchor point, secure the tree-trunk protector or choker-chain around the object. Caution! Always be certain the anchor you select will with- stand the load. Note: how to choose an anchor point: a secure anchor is critical to winching oper...

  • Page 569

    7. Attach the clevis/d-shackle and tree trunk protector. Attach the shackle to the two ends of the strap or chain and through the hook loop, being careful not to over tighten (tighten and back-off 1/2 turn). 8. Lock the clutch. Lock the winch drum by rotating the clutch lever on the winch to engage....

  • Page 570

    10. Put wire rope under tension. Using the remote con- trol switch, slowly wind the wire rope until no slack remains. Once the wire rope is under tension, stand well clear of it and never step over it. 11. Check your anchor. Make sure all connections are secured and free of debris before continuing ...

  • Page 571

    In certain situations you may decide to throw a heavy blanket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway between the winch and the anchor point. Do this before the wire rope is put under tension. Do not approac...

  • Page 572

    14. Begin winching. With the winching vehicles engine on and light tension already on the wire rope, begin winching slowly and steadily. Be sure that the wire rope is winding evenly and tightly around the spool- ing drum. For additional assistance, the winched vehicle can be slowly driven while bein...

  • Page 573

    Note: • avoid overheating the winch motor. For extended winching, stop at reasonable intervals to allow the winch motor to cool down. • what to look for under load: the wire rope must always spool onto the drum as indicated by the drum rotation decal on the winch. As you power-in, make sure the wire...

  • Page 574

    Warning! To prevent serious injury, never put your fingers inside the hook area as you are powering-in. Note: how to spool under no load: arrange the re- mote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope alr...

  • Page 575

    19. Disconnect the remote control. Disconnect the remote control cord from the control box and store in a clean and dry place. Winching operations are now com- plete. Put the cap on the solenoid plug-in. Note: always store the remote control in a protected, clean, dry area. Rigging techniques variou...

  • Page 576

    How to change the pulling direction all winching operations should have a straight line from the winch to the object being pulled. This minimizes the wire rope collecting on one side of the drum affecting pulling efficiency and damaging wire rope. A snatch block, secured to a point directly in front...

  • Page 577

    Double line because pulling power decreases with the number of layers of wire rope on the winch drum, you can use a snatch block to double line out more wire rope. This decreases the number of layers of wire rope on the drum, and increases pulling power. Start by feeding out enough wire rope to free...

  • Page 578

    If the steering icon is flashing, it indicates that the vehicle needs to be taken to the dealer for service. It is likely the vehicle has lost power steering assistance. If the steering icon is displayed and the “power steer- ing system over temp” message is displayed on the evic/did screen, they in...

  • Page 579

    If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers. Note: • increased noise levels at the end of ...

  • Page 580

    Caution! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the new vehicle limited warranty. Warning! Fluid level should be checked on a level surface and with the engine off to prevent injury from movi...

  • Page 581

    When the parking brake is applied with the ignition switch on, the “brake warning light” in the instrument cluster will illuminate. Note: • when the parking brake is applied and the transmis- sion is placed in gear, the “brake warning light” will flash. If vehicle speed is detected, a chime will sou...

  • Page 582

    Warning! • never use the park position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle move- ment and possible injury or damage. • never leave children alone in a vehicle, or with access to an unlocked vehicle. Leaving unattended child...

  • Page 583

    Brake system if power assist is lost for any reason (for example, repeated brake applications with the engine off), the brakes will still function. However, you will experience a substantial increase in braking effort to stop the vehicle. If either the front or rear hydraulic system loses normal bra...

  • Page 584

    With a separate computer to modulate hydraulic pressure to prevent wheel lockup and help avoid skidding on slippery surfaces. The system’s pump motor runs during an abs stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. The abs co...

  • Page 585

    Warning! (continued) • the abs cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • the capabilities of an abs-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize th...

  • Page 586

    Applies optimum pressure to the brakes in emergency braking conditions. This can help reduce braking dis- tances. The bas complements the abs. Applying the brakes very quickly results in the best bas assistance. To receive the benefit of bas, you must apply continuous braking pressure during the sto...

  • Page 587

    During operation, hsa will activate the brake control system and a clicking noise may occur. If your foot is on the brake pedal during operation you may feel a slight pedal movement. The clicking and pedal movement is normal and both will stop when hsa becomes inactive. Hsa activation criteria the f...

  • Page 588

    Towing and hauling with hsa the hsa system does not know if your vehicle is loaded or towing a trailer unless the tow/haul switch, lo- cated on the center stack, is selected. When activated, the “tow/haul indicator light” will illuminate in the instrument cluster. Refer to “automatic transmission” i...

  • Page 589

    Warning! (continued) • hsa is not a parking brake. If you stop the vehicle on a hill without putting the transmission in park or using the parking brake, it will roll down the incline and could collide with another vehicle, object or person, and cause serious or fatal injury. Always remember to use ...

  • Page 590

    Warning! Electronic stability control (esc) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. Esc cannot prevent accidents, in- cluding those resulting from excessive speed in turns, driving on very slipper...

  • Page 591

    Portion of esc, except for the “limited slip” feature described in the tcs section, has been disabled and the # esc off indicator light# will be illuminated. All other stability features of esc function normally. This mode is intended to be used if the vehicle is in deep snow, sand, or gravel condit...

  • Page 592

    All four-wheel drive vehicles in 4wd auto and 4wd lock modes can also choose the following esc operating mode. This is the only selectable esc operating mode in 4wd low: esc full off this mode is intended for off-road use when esc stabil- ity features could inhibit vehicle maneuverability due to tra...

  • Page 593

    Warning! In the %esc full off% mode, the engine torque reduc- tion and stability features are disabled. Therefore, the enhanced vehicle stability offered by esc is unavailable. In an emergency evasive maneuver the esc system will not engage to assist in maintaining stability. “esc full off” mode is ...

  • Page 594

    Note: • the “esc activation/malfunction indicator light” and the “esc off indicator light” come on momen- tarily each time the ignition switch is turned on. • each time the ignition is turned on, the esc system will be on even if it was turned off previously. Except for when the vehicle is started w...

  • Page 595

    Tsc is only active in the default “esc on” mode. Tsc can be disabled by pressing the “esc off” switch and entering “esc partial off” mode. It is not active in the “esc partial off” or “esc full off” modes. Refer to the esc portion of this section for an explanation of the different esc operating mod...

  • Page 596

    Activating hdc once hdc is enabled it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for hdc is selectable by the driver, and can be adjusted by using the electronic range switches located on steering column shifter. The foll...

  • Page 597

    Driver override: the driver may override hdc activation with throttle or brake application at anytime. Deactivating hdc hdc will be deactivated but remain available if any of the following conditions occur: • driver overrides hdc set speed with throttle or brake application. • vehicle speed exceeds ...

  • Page 598

    Feedback to the driver: the instrument cluster has a hdc icon and a hdc switch which has an led which offers feedback to the driver about the state hdc is in. • while hdc is enabled or active the gear position typically associated with ers manual mode will indi- cate target set speed not the top gea...

  • Page 599

    Tire safety information tire markings note: • p (passenger) — metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european — metric tire sizing is based on european design stand...

  • Page 600

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 601

    Example: r = construction code – #r# means radial construction, or – #d# means diagonal or bias construction 15, 16, 18 = rim diameter in inches (in) service description: 95 = load index – a numerical code associated with the maximum load a tire can carry h = speed symbol – a symbol indicating the r...

  • Page 602

    Example: load identification: absence of the following load identification symbols on the sidewall of the tire indicates a standard load (sl) tire: • xl = extra load (or reinforced) tire, or • ll = light load tire or • c, d, e, f, g = load range associated with the maximum load a tire can carry at a...

  • Page 603

    Example: dot ma l9 abcd 0301 dot = department of transportation – this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 604

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours,...

  • Page 605

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. Example tire placard location (door) 5 starting and operating 603.

  • Page 606

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. Example tire placard location (b-pillar) tire and loading information placard 604 starting and operating.

  • Page 607

    3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to t...

  • Page 608

    4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 ...

  • Page 609

    5 starting and operating 607.

  • Page 610

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 611

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Both under-inflation and over-inflation affect the stability of the v...

  • Page 612

    Tire inflation pressures the proper cold tire inflation pressure is listed on the driver’s side b-pillar or rear edge of the driver’s side door. At least once a month: • check and adjust tire pressure with a good quality pocket-type pressure gauge. Do not make a visual judge- ment when determining p...

  • Page 613

    Inflation pressure should be increased by 3 psi (21 kpa), which equals 1 psi (7 kpa) for every 12°f (7°c) for this outside temperature condition. Tire pressure may increase from 2 to 6 psi (13 to 40 kpa) during operation. Do not reduce this normal pressure build up or your tire pressure will be too ...

  • Page 614

    Tire repair if your tire becomes damaged, it may be repaired if it meets the following criteria: • the tire has not been driven on when flat. • the damage is only on the tread section of your tire (sidewall damage is not repairable). • the puncture is no greater than a ¼ of an inch (6 mm). Consult a...

  • Page 615

    Summer tires do not contain the all season designation or mountain/snowflake symbol on the tire sidewall. Use summer tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Warning! Do not use summer tires in snow/ice conditions. You could lose vehi...

  • Page 616

    While studded tires improve performance on ice, skid and traction capability on wet or dry surfaces may be poorer than that of non-studded tires. Some states pro- hibit studded tires; therefore, local laws should be checked before using these tire types. Run flat tires — if equipped run flat tires a...

  • Page 617

    Spare tire matching original equipped tire and wheel — if equipped your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for y...

  • Page 618

    Full size spare — if equipped the full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life. When the tread is worn to the tread wear indicators, the ...

  • Page 619

    Tire spinning when stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stop- ping. Refer to “freeing a stuck vehicle” in “what to do in emergencies” for further information. Warning! Fast spinning ti...

  • Page 620

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes a 1/16 of an inch (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further information. L...

  • Page 621

    Replacement tires the tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressures. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance w...

  • Page 622

    Warning! • do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can caus...

  • Page 623

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. Please follow the table below for proper ...

  • Page 624

    Warning! Using tires of different size and type (m+s, snow) between front and rear axles can cause unpredictable handling. You could lose control and have a collision. Caution! To avoid damage to your vehicle or tires, observe the following precautions: • because of restricted traction device cleara...

  • Page 625

    Tire rotation recommendations tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates. These effects can be reduced by timely rotation of tires. The benefits of rotation are...

  • Page 626

    Directional tires — if equipped for the r/t package with 22” tires and wheels, the rotational direction of the tire must be taken into consid- eration when rotating the tires. The recommended rota- tion pattern for directional tires is shown below. Dual rear wheels — if equipped the tires used on du...

  • Page 627

    Note: if your vehicle is equipped with a tire pressure information system (tpis): • the tire pressure information system (tpis) uses unique sensors in the inner rear wheels to help identify them from the outer rear wheels, because of this, the inner and outer wheel locations can’t be switched. • aft...

  • Page 628

    Caution! (continued) • when replacing a flat, the spare tire may have to be remounted on the rim, or installed at a different location, to maintain the correct placement of the tire on the wheel relative to the tire/wheel position on the truck. For example, if the spare is used to replace an outer r...

  • Page 629

    The tpms will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warn- ing (tire pressure monitoring [tpm] telltale light) illu- minates, you ...

  • Page 630

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, t...

  • Page 631

    • seasonal temperature changes will affect tire pressure, and the tpms will monitor the actual tire pressure in the tire. Premium system the tire pressure monitor system (tpms) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. Sensors mounted to each...

  • Page 632

    The pressure values of each tire with the low tire pressure values in a different color. An #inflate to xx# message will also be displayed. Should this occur, you should stop as soon as possible and inflate the tires with a low pressure condition (those in a different color in the evic/did graphic) ...

  • Page 633

    If the ignition switch is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “tire pressure monitoring telltale light” will no longer flash, and the #service tpm system# message will no longer display, and a pressure value will displ...

  • Page 634

    Vehicles with full size spare 1. The matching full size spare wheel and tire assembly has a tpm sensor that can be monitored by the tpms. 2. If you install the full size spare in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition switch cycle, a chi...

  • Page 635

    • six tpm sensors (dual rear wheel (drw) applica- tions) • pressure display in the electronic vehicle information center (evic)/driver information display (did) the tpis system will display all four (single rear wheel (srw) applications) or six (dual rear wheel (drw) applications) tire pressure valu...

  • Page 636

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 637

    5.7l/6.4l engines this engine is designed to meet all emis- sions regulations and provide satisfactory fuel economy and performance when us- ing high quality unleaded gasoline having an octane range of 87 to 89. The manufac- turer recommends the use of 89 octane for optimum performance. The use of p...

  • Page 638

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in starting and drivability prob- lems, damage critical fuel system...

  • Page 639

    • change the engine oil and oil filter. • disconnect and reconnect the battery to reset the engine controller memory. More extensive repairs will be required for prolonged exposure to e-85 fuel. Mmt in gasoline methylcyclopentadienyl manganese tricarbonyl (mmt) is a manganese-containing metallic add...

  • Page 640

    Caution! (continued) • an out-of-tune engine or certain fuel or ignition malfunctions can cause the catalytic converter to overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate ser- vice. Contact your authorized...

  • Page 641

    Warning! (continued) • guard against carbon monoxide with proper main- tenance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. Flexible fuel (3.6l engine only) — if equipped e...

  • Page 642

    Ethanol fuel (e-85) e-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Warning! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap)...

  • Page 643

    Fuel requirements your vehicle will operate on both unleaded gasoline with an octane rating of 87, or e-85 fuel, or any mixture of these two. For best results, a refueling pattern that alternates between e-85 and unleaded gasoline should be avoided. When you do switch fuel types it is recommended th...

  • Page 644

    Recommends engine oils that are api certified and meet the requirements of material standard ms-6395. Ms-6395 contains additional requirements, developed during ex- tensive fleet testing, to provide additional protection to chrysler group llc engines. Use mopar® or an equivalent oil meeting the spec...

  • Page 645

    Maintenance caution! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect drivability. Adding fuel the fuel filler cap (gas cap) is located behind the fuel filler door, on the left side of the vehicle. Open the fuel door and remove the...

  • Page 646

    Caution! • damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap. • a poorly fitting fuel filler cap could let impurities into the fuel system. • a poorly fitting fuel filler cap may cause the “malfunction indicator light (mil)” to turn o...

  • Page 647

    Warning! Static electricity can cause an ignition of flammable liquid, vapor or gas in any vehicle or trailer. To reduce risk of serious injury or death when filling containers: • always place container on the ground before fill- ing. • keep the pump nozzle in contact with the container when you are...

  • Page 648

    Vehicle loading certification label as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, gross vehicle weight rating (gvwr), gross axle w...

  • Page 649

    Tire size the tire size on the vehicle certification label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim size this is the rim size that is appropriate for the tire size listed. Inflation pressure this is the cold tire inf...

  • Page 650

    Items down low and be sure that the weight is distributed equally. Stow all loose items securely before driving. Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way the brakes operate. Caution! Do not load your vehicle any heavier than the ...

  • Page 651

    Exceed the gvwr. Refer to “vehicle loading/vehicle certification label” in “starting and operating” for further information. Gross trailer weight (gtw) the gtw is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- porary) loaded in or on the trailer ...

  • Page 652

    Frontal area the frontal area is the maximum height multiplied by the maximum width of the front of a trailer. Trailer sway control the trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable...

  • Page 653

    Warning! • an improperly adjusted weight distributing hitch system may reduce handling, stability and braking performance and could result in a collision. • weight distributing systems may not be compat- ible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable ...

  • Page 654

    With weight-distributing hitch (correct) improper adjustment of weight-distributing hitch (incorrect) 652 starting and operating.

  • Page 655

    Recommended distribution hitch adjustment towing with 1500 air suspension 1. Set air suspension to normal ride height. No action is required if already in normal ride height. Note: the vehicle must remain in the engine running position while attaching a trailer for proper leveling of the air suspens...

  • Page 656

    7. Install and adjust the tension in the weight distributing bars so that the height of the front fender is approxi- mately (h2-h1)/3+h1 (about 1/3 the difference be- tween h2 and h1 above normal ride height [h1]). 8. The truck can now be driven. Jack mode will be canceled and vehicle will return to...

  • Page 657

    5. Attach the trailer to the vehicle without the weight distribution bars connected. 6. Measure the height of the top of the front wheel opening on the fender to ground, this is height h2. 7. Install and adjust the tension in the weight distributing bars so that the height of the front fender is app...

  • Page 658

    Trailer hitch type and maximum trailer weight the following chart provides the maximum trailer weight a given factory equipped trailer hitch type can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch type and maximum trailer...

  • Page 659

    Trailer towing weights (maximum trailer weight ratings) note: for additional trailer towing information (maxi- mum trailer weight ratings) refer to the following website addresses: • ramtrucks.Com/en/towing_guide/ • ramtruck.Ca (canada) • rambodybuilder.Com trailer and tongue weight always load a tr...

  • Page 660

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “tire safety information/tire and loading in- formation placard” i...

  • Page 661

    Warning! (continued) • when hauling cargo or towing a trailer, do not overload your vehicle or trailer. Overloading can cause a loss of control, poor performance or dam- age to brakes, axle, engine, transmission, steering, suspension, chassis structure or tires. • safety chains must always be used b...

  • Page 662

    Towing requirements — tires • do not attempt to tow a trailer while using a compact spare tire. • proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “tires – general information” in “starting and oper- ating” for proper tire inflation proce...

  • Page 663

    Caution! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity. Failure to do this could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. • do not interconnect the hydraulic bra...

  • Page 664

    The user interface consists of the following: manual brake control lever slide the manual brake control lever to the left to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the gr...

  • Page 665

    Sliding the manual brake control lever will display the gain setting for 10 seconds and the “trailer brake status indicator light” will not be displayed. If a fault is detected in the trailer wiring or the integrated trailer brake module (itbm), the “trailer brake status indicator light” will flash....

  • Page 666

    5. Press the right arrow on the steering wheel to enter “trailer tow”. 6. Press the up or down buttons until trailer brake type appears on the screen. 7. Press the right arrow and then press the up or down buttons until the proper trailer brake type appears on the screen. 8. In a traffic-free enviro...

  • Page 667

    Display messages the trailer brake control interacts with the electronic vehicle information center (evic) or driver information display (did). Display messages, along with a single chime, will be displayed when a malfunction is deter- mined in the trailer connection, trailer brake control, or on th...

  • Page 668

    Towing requirements — trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The trailer tow package may include a four- and seven- pin wiring harness. Use a factory approved trailer har- nes...

  • Page 669

    Towing tips before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic. Automatic transmission the drive range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, ...

  • Page 670

    When towing a loaded trailer up steep grades at low speeds (20 mph [32 km/h] or below), holding your vehicle in first gear (using the ers shift control) can help to avoid transmission overheating. If you regularly tow a trailer for more than 45 minutes of continuous operation, then change the automa...

  • Page 671

    Air conditioning turn off temporarily. Air suspension system to aid in attaching/detaching the trailer from the vehicle, the air suspension system can be used. Refer to “air suspension system” in “starting and operating” for further information. Note: the vehicle must remain in the engine running po...

  • Page 672

    Warning! (continued) do not expect that the airbag will perform as de- scribed earlier in this manual. 2500/3500 models only snowplow prep packages are available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow. Note: before installatio...

  • Page 673

    • check the runners and cutting edge for excessive wear. The cutting edge should be ¼ to ½ in (6 cm to 1.2 cm) above ground in snow plowing position. • check that snowplow lighting is connected and func- tioning properly. Snowplow prep package model availability for information about snowplow applic...

  • Page 674

    Maintain and operate your vehicle and snowplow equip- ment following the recommendations provided by the specific snowplow manufacturer. Over the road operation with snowplow attached the blade restricts air flow to the radiator and causes the engine to operate at higher than normal temperatures. Th...

  • Page 675

    Recreational towing (behind motorhome, etc.) towing this vehicle behind another vehicle towing condition wheels off the ground two-wheel drive models four-wheel drive models flat tow none not allowed see instructions • automatic transmission in park • manual transmission in gear (not in neutral) • t...

  • Page 676

    Note: vehicles equipped with air suspension must be placed in transport mode before tying them down (from the body) on a trailer or flatbed truck. Refer to “air suspension – if equipped” for more information. If the vehicle cannot be placed in transport mode (for example, engine will not run), tie-d...

  • Page 677

    Caution! • towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper towing is not covered under the new vehicle limited warranty. • do not disconnect the driveshaft because fluid may leak from the transmission, causing damage to internal parts. Recreation...

  • Page 678

    Caution! (continued) • tow only in the forward direction. Towing this vehicle backwards can cause severe damage to the transfer case. • automatic transmissions must be placed in park for recreational towing. • manual transmissions must be placed in gear (not in neutral) for recreational towing. • be...

  • Page 679

    Warning! (continued) the parking brake. The transfer case neutral (n) position disengages both the front and rear drive- shafts from the powertrain and will allow the vehicle to roll, even if the transmission is in park. The parking brake should always be applied when the driver is not in the vehicl...

  • Page 680

    5. Release the parking brake. 6. Shift the transmission into reverse. 7. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 8. Repeat steps 7 and 8 with automatic transmission in drive or manual transmission in first gear...

  • Page 681

    • the ignition switch must be in the on/run position for a shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the on/run position, the shift will not take place and no position indicator lights will be on or flashing. • a flashing neutral (n) p...

  • Page 682

    (n) button has been released, the transfer case will shift to the position indicated by the selector switch. • with electronic shift transfer case with pushbutton selector switch, press and hold the switch for the desired transfer case position, until the neutral (n) indicator light turns off and th...

  • Page 683

    The shift, the neutral (n) indicator light will flash continuously until all requirements are met or until the button is released. • the ignition switch must be in the on/run position for a shift to take place and for the position indicator lights to be operable. If the ignition switch is not in the...

  • Page 685: Contents

    What to do in emergencies contents ! Hazard warning flashers . . . . . . . . . . .685 ! If your engine overheats . . . . . . . . . . . .685 ! Wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .686 ▫ torque specifications . . . . . . . . . . . . . . . . . .686 ! Jacking a...

  • Page 686

    ! Manual park release — 8 speed transmission . . . . . . . . . . . . . . . . . . . . . . .738 ! Towing a disabled vehicle . . . . . . . . . . .740 ▫ two-wheel drive models . . . . . . . . . . . . . . . .742 ▫ four-wheel drive models. . . . . . . . . . . . . . . .743 684 what to do in emergencies.

  • Page 687

    Hazard warning flashers the hazard warning flasher switch is located on the upper switch bank just below the radio. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency. Pre...

  • Page 688

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on hot (h), and you hear conti...

  • Page 689

    Note: dual wheels are flat mounted, center piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the lug nut/bolt and the washer. Do not oil wheel studs. Inspect the wheel mounting surface ...

  • Page 690

    After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may ...

  • Page 691

    Warning! (continued) • being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be ra...

  • Page 692

    Passengers seat. To remove the cover, pull the front part of the cover (closest to the front of the seat) toward you to release a locking tab. Once the front of the cover is loose, slide the cover toward the front of the seat until it is free from the seat frame. Remove the jack and tools by turning...

  • Page 693

    Release the tool bag straps from the jack and remove tools from bag. There are 2 ways to assemble the tools: assembled for spare tire lowering/raising jack and tool bag assembled for spare tire lowering/raising 1 — extension 3 3 — extension 1 2 — extension 2 4 — wheel wrench 6 what to do in emergenc...

  • Page 694

    Caution! • the wheel wrench can only be attached to exten- sion 1. • when attaching the tool to the winch mechanism be sure the large flared end opening on extension 3 is positioned correctly over the winch mechanism adjusting nut. • damage to the wheel wrench, extensions and winch mechanism may occ...

  • Page 695

    Warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious in...

  • Page 696

    2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. Rotating the wheel wrench handle pulling t...

  • Page 697

    4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. 5. Pull the retainer through the center of the wheel. Note: the winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and...

  • Page 698

    Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on...

  • Page 699

    Jack instructions (1500 series) warning! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. • turn on the hazard warning flasher. •...

  • Page 700

    Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the jacking instructions for this vehicle. 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise...

  • Page 701

    When changing a front wheel, place the scissor jack under the rear portion of the lower control arm as shown below. 4x4 series trucks front jacking location there is a jack location indicator on the rear portion of the lower control arm. 4x2 front jacking location 4x4 front jacking location indicato...

  • Page 702

    When changing a front wheel, place the scissor jack under the rear portion of the lower control arm as shown below. 4x2 and 4x4 rear jacking location operate the jack using the jack drive tube and the wheel wrench. The tube extension may be used but is not required. For 4x2 and 4x4 trucks, when chan...

  • Page 703

    Connect the jack tube extension and wheel wrench. Caution! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By rotating the lug wrench clockwise, raise the vehicle until the wheel just clears the sur...

  • Page 704

    Each nut has been tightened twice. For the correct lug nut torque refer to “torque specifications” in this section. If in doubt about the correct tightness, have them checked with a torque wrench by you authorized dealer or service station. Warning! A loose tire or jack thrown forward in a collision...

  • Page 705

    Warning! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immedi- ately. 1. Turn the wheel so that the valve stem is facing the ground and toward the rear of the vehicle for conve- nience in checking...

  • Page 706

    2. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable and position it properly across the wheel opening. 3. Attach the wheel wrench to the jack extension tube with the curved angle facing away from the vehicle. Insert the tube through the access hole bet...

  • Page 707

    4. Rotate the wheel wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip, or click three or four times. It cannot be overtightened. Push against the tire several times to ensure it is firmly in pl...

  • Page 708

    3. Secure the tool bag straps to the jack. 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor. Jack and tool bag jack and tools tied 706 what to do in emerg...

  • Page 709

    Note: ensure that the jack slides into the front hold down location. 5. Turn the wing bolt clockwise to secure to the floor pan. Reinstall the plastic cover. Warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving (continued) jack hold down ...

  • Page 710

    Warning! (continued) you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. Jacking and tire changing 2500 and 3500 series trucks warning! • do not attempt to chang...

  • Page 711

    Jack location the jack and jack tools are stored under the front passenger seat. Removal of jack and tools (2500, 3500 series) to access the jack and jack tools you must remove the plastic access cover, located on the side of the front passengers seat. To remove the cover, pull the front part of the...

  • Page 712

    Remove the jack and tools from the bracket assembly. Turn the jack-turn-screw counterclockwise to release jack from bracket assembly. Wing bolt/jack and tools (2500/3500 series) jack and tools bracket assembly 710 what to do in emergencies.

  • Page 713

    There are 2 ways to assemble the tools: assembled for spare tire lowering/raising caution! • the wheel wrench can only be attached to exten- sion 1. • when attaching the tool to the winch mechanism be sure the large flared end opening on extension 3 is positioned correctly over the winch mechanism a...

  • Page 714

    Assembled for jack operation warning! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid accelera- tion or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with f...

  • Page 715

    2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. Inserting the jack extension tube into the access hole rotating the wheel wrench handle 6 what to do in emergencies 713.

  • Page 716

    3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. 4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. Pulling the spare tire out gaining access to the retainer 714 what to do in emergencies.

  • Page 717

    5. Pull the retainer through the center of the wheel. Note: the winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippe...

  • Page 718

    5. Turn the ignition off. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jack instructions (250...

  • Page 719

    Warning! (continued) • only use the jack in the positions indicated and for lifting this vehicle during a tire change. • if working on or near a roadway, be extremely careful of motor traffic. • to assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve s...

  • Page 720

    1. Remove the spare wheel, jack, and tools from storage. 2. Using the lug wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. Changing a dually tire requires the lug wrench adapter. Note: if your vehicle is equipped with...

  • Page 721

    3. Placement of the jack: front jacking location when changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube...

  • Page 722

    Rear jacking location when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle between the spring and the shock absorber with the drive tubes extending to the rear. Connect the jack tube extension and wheel w...

  • Page 723

    5. Remove the wheel nuts and pull the wheel off. On single rear-wheel (srw) trucks, install the spare wheel and wheel nuts with the cone shaped end of the wheel nuts toward the wheel. On 3500 dual rear-wheel models (drw) trucks, if the outer tire is being re- placed then leave the inner wheel on the...

  • Page 724

    6. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. For the correct lug nut torque refer to “torque specifications” in this section. If in doubt about the cor...

  • Page 725

    9. Adjust the tire pressure when possible. Note: do not oil wheel studs. For chrome wheels, do not substitute with chrome plated wheel nuts. To stow the flat or spare note: have the flat tire repaired or replaced immedi- ately. Warning! A loose tire thrown forward in a collision or hard stop could i...

  • Page 726

    2. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable and position it properly across the wheel opening. 3. Attach the wheel wrench to the jack extension tube with the curved angle facing away from the vehicle. Insert the tube through the access hole bet...

  • Page 727

    4. Rotate the wheel wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip, or click three or four times. It cannot be overtightened. Push against the tire several times to ensure it is firmly in pl...

  • Page 728

    3. Place the jack and tool bracket assembly in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor. Note: ensure that the jack and tool bracket assembly slides into the front hold down loc...

  • Page 729

    Hub caps/wheel covers — if equipped the hub caps must be removed before raising the vehicle off the ground. Caution! Use extreme caution when removing the front and rear center caps. Damage can occur to the center cap and/or the wheel if screwdriver type tools are used. A pulling motion, not a pry o...

  • Page 730

    On 3500 models with dual rear wheels (drw), you must first remove the hub caps. The jack handle driver has a hook at one end that will fit in the pull off notch of the rear hub caps. Position the hook and pull straight out on the ratchet firmly. The hub cap should pop off. The wheel skins can now be...

  • Page 731

    Caution! Never use a floor jack directly under the differential housing of a loaded truck or damage to your vehicle may result. Jump-starting procedures if your vehicle has a discharged battery it can be jump- started using a set of jumper cables and a battery in another vehicle or by using a portab...

  • Page 732

    Battery (gas model shown) 1 — positive battery post 2 — fuses battery (diesel model shown) 1 — positive battery post 2 — fuses 730 what to do in emergencies.

  • Page 733

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 734

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. Note: do not jump off fuses...

  • Page 735

    Caution! Do not connect jumper cable to any of the fuses on the positive battery terminal. The resulting electrical current will blow the fuse. 6. Once the engine is started, remove the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative (-) end of the j...

  • Page 736

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand, or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse (with automatic transmission) or 2nd gear a...

  • Page 737

    Caution! • when “rocking” a stuck vehicle by shifting be- tween drive/2nd gear and reverse, do not spin the wheels faster than 15 mph (24 km/h), or drive- train damage may result. • revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damag...

  • Page 738

    Warning! • do not use a chain for freeing a stuck vehicle. Chains may break, causing serious injury or death. • stand clear of vehicles when pulling with tow hooks. Tow straps may become disengaged, caus- ing serious injury. Caution! Tow hooks are for emergency use only to rescue a vehicle stranded ...

  • Page 739

    6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. Center console shifter — if equipped 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Using a small screwdriver or similar tool, remove the shift lever override access cover (located to the r...

  • Page 740

    6. Move the shift lever to the neutral position. 7. The vehicle may then be started in neutral. 8. Reinstall the shift lever override access cover. Manual park release — 8 speed transmission warning! Always secure your vehicle by fully applying the parking brake, before activating the manual park re...

  • Page 741

    Follow these steps to activate the manual park release: 1. Firmly apply the parking brake. 2. Using a small screwdriver or similar tool, remove the manual park release access cover, which is just above the parking brake release handle, below and to the left of the steering column. 3. Using the screw...

  • Page 742

    To reset the manual park release: 1. Push the locking tab to the right, to unlock the lever. 2. Rotate the manual park release lever forward to its original position, until the locking tab snaps into place to secure the lever. 3. Pull gently on the tether strap to confirm that the lever is locked in...

  • Page 743

    Towing condition wheels off the ground 2wd models 4wd models flat tow none if transmission is operable: • transmission in neutral • 30 mph (48 km/h) max speed • 15 miles (24 km) max distance (6–speed transmission) • 30 miles (48 km) max distance (8–speed transmission) see instructions in “recreation...

  • Page 744

    If you must use the accessories (wipers, defrosters, etc.) while being towed, the ignition must be in the on/run position, not the acc position. If the key fob is unavailable or the vehicle’s battery is discharged, refer to ”manual park release” or “shift lever override” in this section for instruct...

  • Page 745

    And the rear wheels on a towing dolly, or (when using a suitable steering wheel stabilizer to hold the front wheels in the straight position) with the rear wheels raised and the front wheels on the ground. Caution! Towing this vehicle in violation of the above require- ments can cause severe engine ...

  • Page 747: Maintaining Your Vehicle

    Maintaining your vehicle contents ! Engine compartment — 3.6l . . . . . . . . . .748 ! Engine compartment — 5.7l . . . . . . . . . .749 ! Engine compartment — 6.4l . . . . . . . . . .750 ! Onboard diagnostic system (obd ii) . . .751 ▫ loose fuel filler cap message . . . . . . . . . . . .751 ! Emissi...

  • Page 748

    ▫ adding washer fluid . . . . . . . . . . . . . . . . . .771 ▫ exhaust system . . . . . . . . . . . . . . . . . . . . . .772 ▫ cooling system . . . . . . . . . . . . . . . . . . . . . .774 ▫ brake system . . . . . . . . . . . . . . . . . . . . . . . .782 ▫ rear axle and 4x4 front driving axle fluid ...

  • Page 749

    ! Fluid capacities . . . . . . . . . . . . . . . . . . . .819 ! Fluids, lubricants and genuine parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .821 ▫ engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .821 ▫ chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . .8...

  • Page 750

    Engine compartment — 3.6l 1 — air cleaner filter 5 — battery 2 — engine oil dipstick 6 — washer fluid reservoir 3 — engine oil fill 7 — power distribution center (fuses) 4 — brake fluid reservoir 8 — engine coolant reservoir 748 maintaining your vehicle.

  • Page 751

    Engine compartment — 5.7l 1 — air cleaner filter 7 — washer fluid reservoir 2 — automatic transmission dipstick (6-speed trans only) 8 — power distribution center (fuses) 3 — engine oil fill 9 — power steering fluid reservoir (2500/3500 models only) 4 — engine oil dipstick 10 — coolant pressure cap ...

  • Page 752

    Engine compartment — 6.4l 1 — coolant pressure bottle 6 — battery 2 — transmission dipstick 7 — power distribution center (fuses) 3 — engine oil fill 8 — washer solvent 4 — engine oil dipstick 9 — power steering fluid reservoir 5 — brake fluid reservoir 10 — air cleaner filter 750 maintaining your v...

  • Page 753

    Onboard diagnostic system (obd ii) your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 754

    (evic)” or “driver information display (did)” in “un- derstanding your instrument panel” for further informa- tion. Tighten the fuel filler cap properly and press the select button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loos...

  • Page 755

    3. Approximately 15 seconds later, one of two things will happen: • the mil will flash for about 10 seconds and then return to being fully illuminated until you turn off the ignition or start the engine. This means that your vehicle’s obd ii system is not ready and you should not proceed to the i/m ...

  • Page 756

    Dealer service your authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting...

  • Page 757

    Caution! (continued) • your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance inter- vals. Do not use chemical flushes in these compo- nents as the chemicals can damage your engine, transmission, power steering...

  • Page 758

    Change engine oil the oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Refer to the “maintenance schedule” for further informa- tion. Note: 1500 models only • under no circumstances should oil change intervals exceed 10,000 miles (16,000 ...

  • Page 759

    Caution! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the new vehicle limited warranty. Engine oil viscosity — 3.6l engines (1500 models only) mopar® sae 5w-20 engine oil approved to chrysler material standard ms-6395 or equiva...

  • Page 760

    • for 2500/3500 trucks with a 5.7l engine operating under a gross combined weight rating of 14,000 lbs (6 350 kg) or greater, sae 5w-30 engine oil is recom- mended for all operating temperatures. Engine oil viscosity — 6.4l engine use pennzoil ultra™ 0w–40 engine or equivalent mopar® oil meeting the...

  • Page 761

    Engine air cleaner filter refer to the “maintenance schedule” for the proper maintenance intervals. Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unles...

  • Page 762

    Engine air cleaner filter removal 1. Release the spring clips from the air cleaner cover. 3.6l/5.7l air cleaner filter cover 1 — clean air hose clamp 2 — air hose 3 — spring clips 6.4l air cleaner filter cover 1 — clean air hose clamp 2 — spring clips 760 maintaining your vehicle.

  • Page 763

    2. Lift the air cleaner cover to access the air cleaner filter. 3. Remove the air cleaner filter element from the housing assembly. Open air cleaner filter assembly 1 — air cleaner cover 2 — air cleaner filter air cleaner filter 1 — air cleaner filter 2 — air cleaner filter inspection surface 7 main...

  • Page 764

    Engine air cleaner filter installation note: inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleaner filter inspection surface facing downward. 2. Install the air clea...

  • Page 765

    Normal. Any belt with cracks running along a rib must be replaced. Also have the belt replaced if it has excessive wear, frayed cords or severe glazing. Conditions that would require replacement: • rib chunking (one or more ribs has separated from belt body) • rib or belt wear • longitudinal belt cr...

  • Page 766

    Maintenance-free battery your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- tenance required. Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or...

  • Page 767

    Caution! • it is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and are identified on the battery case. Cable clamps should be ...

  • Page 768

    Caution! Do not use chemical flushes in your air conditioning system as the chemicals can damage your air condi- tioning components. Such damage is not covered by the new vehicle limited warranty. Refrigerant recovery and recycling r134a — if equipped r-134a air conditioning refrigerant is a hydrofl...

  • Page 769

    Body lubrication locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as mopar® spray white lube to assure quiet, easy...

  • Page 770

    The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems are experienced. This inspection should include the fol- lowing points: • wear or uneven edges • foreign material • hardening or cracking • deformation or fatigue if a wiper blade or wiper arm ...

  • Page 771

    2. To disengage the wiper blade from the wiper arm, press the release tab on the wiper blade and while holding the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm. Wiper blade with release tab in locked position 1 — wiper blade 2 — wiper arm 3 — release tab 7 ma...

  • Page 772

    3. With the wiper blade disengaged, remove the wiper blade from the wiper arm. 4. Gently lower the wiper arm onto the glass. Wiper blade with release tab in unlocked position 1 — wiper blade 2 — wiper arm 3 — release tab wiper blade removed from wiper arm 1 — wiper blade 2 — wiper arm 3 — release ta...

  • Page 773

    Installing the front wipers 1. Lift the wiper arm off of the glass, until the wiper arm is in the full up position. 2. Position the wiper blade near the hook on the tip of the wiper arm. 3. Insert the hook on the tip of the arm through the opening in the wiper blade. 4. Slide the wiper blade up into...

  • Page 774

    Warning! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. After the engine has warmed up, operate the defroster for a few minutes to reduce the possibility of smearing or freezi...

  • Page 775

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 776

    Under normal operating conditions, the catalytic converter will not require maintenance. However, it is important to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in civil...

  • Page 777

    Engine coolant checks check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or rusty in appearance, the system should be drained, flushed and refilled with fresh coolant. Check the front ...

  • Page 778

    Selection of coolant refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Caution! • mixing of engine coolant (antifreeze) other than speci- fied organic additive technology (oat) engine cool- ant (antifreeze), may result in engine damage and may de...

  • Page 779

    You use the same engine coolant (oat coolant conform- ing to ms-12106) throughout the life of your vehicle. Please review these recommendations for using organic additive technology (oat) engine coolant (antifreeze) that meets the requirements of chrysler material stan- dard ms-12106. When adding en...

  • Page 780

    Cooling system pressure cap the cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that the engine coolant (antifreeze) will return to the radiator from the coolant expansion bottle. The cap should be inspected and cleaned if there is any accumulation of foreig...

  • Page 781

    Checking coolant level — 3.6l and 5.7l engines with the engine off and cold, the level of the engine coolant should be between the add and safe range on the dipstick. To check the coolant level: 1. Open the coolant reservoir. 2. Lift and remove the plastic dipstick from the reservoir neck. Opening t...

  • Page 782

    3. Check the coolant level on the dipstick. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for engine coolant (antifreeze) freeze point or replacing engine coolant (antifreeze). Advise your service attendant of this. As long as the engin...

  • Page 783

    Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when th...

  • Page 784

    Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenance schedule” for the proper maintenance intervals. Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot rest...

  • Page 785

    Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid ...

  • Page 786

    Warning! (continued) • do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Rear axle and 4x4 front driving axle fluid level for normal service, periodic fluid level che...

  • Page 787

    Note: the presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. Limited-slip differ...

  • Page 788

    Automatic transmission selection of lubricant it is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use only the manufacturer’s specified transmission fluid. Refer to “fluids, lubricants, and genuine parts” in this section for fluid specifications....

  • Page 789

    Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check — eight-speed transmission the fluid level is preset at the factory and does not require adjustment ...

  • Page 790

    Use the following procedure to check the transmission fluid level properly: 1. Monitor the transmission temperature using the evic/did screen, and operate the vehicle as required to reach the normal operating temperature. If the transmission is not functioning properly, or the vehicle cannot be driv...

  • Page 791

    Note: if it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “cold” (lower) holes on the dipstick with the fluid at 60-70°f / 16-21°c. Only use the cold region of the dipstick as a rough reference when setting the fluid level after a t...

  • Page 792

    Fluid and filter changes refer to the “maintenance schedule” for the proper maintenance intervals. In addition, change the fluid and filters if the fluid becomes contaminated (with water, etc.), or if the trans- mission is disassembled for any reason. Appearance care and protection from corrosion pr...

  • Page 793

    Washing • wash your vehicle regularly. Always wash your ve- hicle in the shade using mopar® car wash, or a mild car wash soap, and rinse the panels completely with clear water. • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover...

  • Page 794

    • if your vehicle is damaged due to a collision or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibility of the owner. • if you carry special cargo such as chemicals, fertilizers, de-ice...

  • Page 795

    Caution! (continued) or harsh brushes that may damage the wheel’s pro- tective finish. Only mopar® wheel cleaner or equivalent is recommended. Stain repel fabric cleaning procedure — if equipped stain repel seats may be cleaned in the following man- ner: • remove as much of the stain as possible by ...

  • Page 796

    And mopar® total clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather conditioner is not required to mainta...

  • Page 797

    Cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear quarter window equipped with the radio antenna. Do not use scrapers or other sharp instrument that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel ...

  • Page 798

    Warning! (continued) assemblies must be replaced after a collision if they have been damaged (i.E., bent retractor, torn web- bing, etc.). Tri-fold soft tonneau cover care for cleaning and protecting the vinyl tri-fold tonneau cover, use mopar® whitewall & vinyl top cleaner and mopar® leather and vi...

  • Page 799

    Warning! Do not use silicon-based protection products to clean your bedliner. Silicon-based products can become slippery and may result in personal injury. Spray-on bedliners are chemically-resistant to many different types of chemicals (including gasoline, oil, hydraulic fluids) for short periods o...

  • Page 800

    Warning! (continued) • before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged. • if the replaced fuse blows again, contact an autho- rized dealer. • if a general protection fuse for safety systems (air bag system, braking system...

  • Page 801

    Cavity cartridge fuse micro fuse description f01 80 amp black rad fan control module – if equipped f03 60 amp yellow rad fan – if equipped f05 40 amp green compressor for air suspension – if equipped f06 40 amp green antilock brakes/electronic stability control pump f07 40 amp green starter solenoid...

  • Page 802

    Cavity cartridge fuse micro fuse description f10 40 amp green body controller / exterior lighting #2 f10 50 amp red body controller / exterior lighting #2 – if equipped with stop/start f11 30 amp pink integrated trailer brake module – if equipped f12 40 amp green body controller #3 / interior lights...

  • Page 803

    Cavity cartridge fuse micro fuse description f22 20 amp blue 30 amp pink (cummins diesel) engine control module f23 30 amp pink body controller #1 f24 30 amp pink driver door module f25 30 amp pink front wiper f26 30 amp pink antilock brakes/stability control module/ valves f28 20 amp blue trailer t...

  • Page 804

    Cavity cartridge fuse micro fuse description f34 30 amp pink vehicle system interface module #2 – if equipped f35 30 amp pink sunroof – if equipped f36 30 amp pink rear defroster– if equipped f37 30 amp pink cummins diesel fuel heater #2 if equipped f38 30 amp pink power inverter 115v ac– if equippe...

  • Page 805

    Cavity cartridge fuse micro fuse description f52 5 amp tan battery sensor f53 20 amp yellow trailer tow – left turn/stop lights f54 20 amp yellow adjustable pedals f56 15 amp blue additional diesel content – if equipped f57 20 amp yellow transmission f58 20 amp yellow spare fuse f59 10 amp red scr r...

  • Page 806

    Cavity cartridge fuse micro fuse description f65 10 amp red usb interface f66 10 amp red sunroof / passenger window switches / rain sensor f67 10 amp red cd / dvd / bluetooth hands-free module – if equipped f69 15 amp blue mod scr 12v (cummins diesel) – if equipped f70 30 amp green fuel pump motor f...

  • Page 807

    Cavity cartridge fuse micro fuse description f76 10 amp red antilock brakes/electronic stability control f77 10 amp red drivetrain control module/front axle discon- nect module f78 10 amp red engine control module / electric power steering f79 15 amp blue clearance lights f80 10 amp red universal ga...

  • Page 808

    Cavity cartridge fuse micro fuse description f88 15 amp blue instrument panel cluster f90/f91 20 amp yellow power outlet (rear seats) customer selectable f93 20 amp yellow cigar lighter f94 10 amp red shifter / transfer case module f95 10 amp red rear camera / park assist f96 10 amp red rear seat he...

  • Page 809

    Caution! • when installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • when replacing a blown fuse,...

  • Page 810

    Replacement bulbs all of the inside bulbs are brass or glass-wedge base. Aluminum base bulbs are not approved. Interior bulbs bulb number overhead console lamps ts 212–9 dome lamp 7679 for lighted switches, see your authorized dealer for replacement instructions. Exterior bulbs bulb number base quad...

  • Page 811

    Bulb number fog lamp (horizontal shape) 9145 fog lamp (vertical shape) 9006 center high mounted stop lamp (chmsl) 921k rear cargo lamp 921 led center high mounted stop lamp (chmsl)/cargo lamp led (serviced at authorized dealer) cab roof marker lamps 194na base rear tail/turn and stop lamp 3157k prem...

  • Page 812

    Base quad / premium bi-halogen: low beam headlamp, high beam headlamp, front park and turn — if equipped 1. Open the hood. 2. Disconnect and isolate the negative battery cable. 3. Remove the six plastic push-in fasteners that secure the upper radiator seal to the grille support and both fender ledge...

  • Page 813

    8. Reach through the access hole of the wheel house splash shield and lift the slide lock upward far enough to disengage it from the lock post on the back of the front lamp unit housing. 9. Remove the headlamp assembly. Grasp the outboard edge of the lamp and pull it straight forward to disengage th...

  • Page 814

    Fog lamps — if equipped 1. Reach under and behind the front bumper to access the back of the front fog lamp housing. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise ¼ turn to unlock the bulb from the housing. 4. Pull the bulb straight o...

  • Page 815

    2. Pull the outboard side of the lamp rearward far enough to unsnap the two receptacles on the outboard side of the lamp housing from the two plastic snap post retainers in the outer box side panel. 3. Disconnect the wiring harness connectors from the bulb socket. 4. Rotate the bulb socket countercl...

  • Page 816

    Center high-mounted stoplamp (chmsl) with cargo lamp 1. Remove the two screws holding the housing/lens to the body as shown. 2. Separate the connector holding the housing and wir- ing harness to the body. Chmsl mounting screw locations chmsl connector location 814 maintaining your vehicle.

  • Page 817

    3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing. 4. Pull the desired bulb straight from the socket. Caution! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • outs...

  • Page 818

    Cab top clearance lamps — if equipped 1. Remove the two screws from the top of the lamp. 2. Rotate the bulb socket ¼ turn and pull it from the lamp assembly. Removing rear screw from clearance lamp removing bulb socket from clearance lamp 816 maintaining your vehicle.

  • Page 819

    3. Pull the bulb straight from it’s socket and replace. Rear lamp bar id marker (dual rear wheels) — if equipped 1. Loosen the two screws and the housing to gain access to the bulb sockets. 2. Turn the socket ¼ turn counterclockwise to access the bulb. 3. Pull the bulb straight out from the socket. ...

  • Page 820

    Side marker lamps (dual rear wheels) — if equipped 1. Push rearward on the side marker lamp assembly. 2. Pull the entire assembly from the fender. 3. Turn the socket ¼ turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5. Reverse the procedu...

  • Page 821

    Fluid capacities u.S. Metric fuel (approximate) 1500 regular cab shortbed/crew quad cab models 26 gallons 98 liters 1500 regular cab longbed/crew quad cab models (optional) 32 gallons 121 liters 2500/3500 shortbed models 31 gallons 117 liters 2500/3500 longbed models 32 gallons 121 liters engine oil...

  • Page 822

    U.S. Metric cooling system 3.6l engine (we recommend you use mopar® antifreeze/ coolant 10 year/150,000 mile formula that meets the require- ments of chrysler material standard ms-12106.) 13.7 quarts 13 liters 5.7l engine – 1500 models (we recommend you use mopar® antifreeze/coolant 10 year/150,000 ...

  • Page 823

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology). Engine oil – 3.6l engine we recommend you use api certified sae 5w-20 engine oil, meet...

  • Page 824

    Component fluid, lubricant, or genuine part engine oil – 5.7l engine 2500/3500 trucks operating under a gross com- bined weight rating greater than 14,000 lbs/(6,350 kg.) we recommend you use api certified sae 5w-30 engine oil, meeting the requirements of chrysler material standard ms-6395 such as m...

  • Page 825

    Caution! • mixing of engine coolant (antifreeze) other than specified organic additive technology (oat) en- gine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic additive technology (oat) engine cool- ant is different and should not be mixed with hybri...

  • Page 826

    Chassis component fluid, lubricant, or genuine part automatic transmission – eight-speed automatic use only mopar® zf 8&9 speed atf™ automatic transmission fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Automatic transmission – six...

  • Page 827

    Component fluid, lubricant, or genuine part rear axle – 1500 models we recommend you use mopar® synthetic gear lu- bricant sae 75w-140 (ms-8985). Limited-slip rear ax- les require the addition of 5 oz. (148 ml) mopar® limited slip additive (ms-10111). Front and rear axle – 2500/3500 models we recomm...

  • Page 829: Maintenance Schedules

    Maintenance schedules contents ! Maintenance schedule . . . . . . . . . . . . .828 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .831 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 830

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This...

  • Page 831

    Note: 1500 models only • under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or twelve months on 1500 trucks, whichever comes first. 2500 – 3500 models • under no circumstances should oil change intervals exceed 8,000 miles (13,000 km) or twelve months on 2500 – 3500 t...

  • Page 832

    Required maintenance refer to the maintenance schedules on the following pages for required maintenance. At every oil change interval as indicated by oil change indicator system: • change oil and filter. • rotate the tires. Rotate at the first sign of irregu- lar wear, even if it occurs before the o...

  • Page 833

    Maintenance chart mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176...

  • Page 834

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 835

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 836

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 837

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 839: Contents

    If you need consumer assistance contents ! Suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .839 ▫ prepare for the appointment. . . . . . . . . . . . .839 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .839 ▫ be reasonable with requests ....

  • Page 840

    ! Department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .845 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .845 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .845 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .846 838 if...

  • Page 841

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 842

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 843

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 844

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 845

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 846

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 847

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 848

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 849: Index

    Index 10

  • Page 850

    Adding engine coolant (antifreeze) . . . . . . . . . . . .776 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .643 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .637 adjustable pedals . . . . . . . . . . . . . . . . . . . . . . . . .185 air bag . . . . . . ....

  • Page 851

    Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .232 auto down power windows . . . . . . . . . . . . . . . . . .47 automatic door locks . . . . . . . . . . . . . . . . . . . . . .40 automatic headlights . . . . . . . . . . . . . . . . . . . . . .167 automatic high beams . . . ....

  • Page 852

    Cab top clearance lights . . . . . . . . . . . . . . . . . . .816 camera, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . .210 camper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .268 capacities, fluid . . . . . . . . . . . . . . . . . . . . . . . . . .819 caps, filler oi...

  • Page 853

    Automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .410 cold weather operation . . . . . . . . . . . . . . . . . . . .451 compact disc (cd) maintenance . . . . . . . . . . . . . .397 compact spare tire . . . . . . . . . . . . . . . . . . . . . . . .615 console, overhead . . . . . . . . ...

  • Page 854

    Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 remote keyless entry (rke) . . . . . . . . . . . . . . . .37 door locks, automatic . . . . . . . . . . . . . . . . . . . . . .40 door opener, garage. . . . . . . . . . . . . . . . . . . . . . .214 driving off-pavement . . . . . ....

  • Page 855

    Break-in recommendations . . . . . . . . . . . . . . . .113 compartment . . . . . . . . . . . . . . . . . . . . . . . . . .748 compartment identification . . . . . . . . . . . . . . . .748 coolant (antifreeze) . . . . . . . . . . . . . . . . . . . . .821 exhaust gas caution . . . . . . . . . . . . ....

  • Page 856

    Flooded engine starting . . . . . . . . . . . . . . . . . . . .451 fluid, brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .824 fluid capacities . . . . . . . . . . . . . . . . . . . . . . . . . .819 fluid leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 fluid level ch...

  • Page 857

    Gear ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . .471 gear select lever override . . . . . . . . . . . . . . . . . .736 general information . . . . . . . . . . . . . . . . . . . . . . .634 glass cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .794 grocery bag retainer...

  • Page 858

    Illuminated entry . . . . . . . . . . . . . . . . . . . . . . . . . .23 immobilizer (sentry key) . . . . . . . . . . . . . . . . . . . .18 inflation pressure tires . . . . . . . . . . . . . . . . . . . . .620 information center, vehicle . . . . . . . . . . . . . . . . . .302 inside rearview mirror ....

  • Page 859

    Lead free gasoline . . . . . . . . . . . . . . . . . . . . . . . .634 leaks, fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . .618 light bulbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 lights ...

  • Page 860

    Tire pressure monitoring (tpms) . . . . . . . . . . . .294 traction control . . . . . . . . . . . . . . . . . . . . . . . .591 transfer case . . . . . . . . . . . . . . . . . . . . . . . . . .497 turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 warning (instrument cluster descr...

  • Page 861

    Multi-function control lever. . . . . . . . . . . . . . . . .176 navigation system (uconnect® gps) . . . . . . . . . . . .210 new vehicle break-in period . . . . . . . . . . . . . . . . .113 occupant restraints . . . . . . . . . . . . . . . . . . . . . . . .50 octane rating, gasoline (fuel) . . . . ...

  • Page 862

    Personal settings. . . . . . . . . . . . . . . . . . . . . . . . . .324 pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 pets, transporting . . . . . . . . . . . . . . . . . . . . . . . . .113 pickup box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251 placa...

  • Page 863

    Shifting out of transfer case neutral (n) . . . . . .679 reformulated gasoline . . . . . . . . . . . . . . . . . . . . .635 refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .766 reminder, seat belt. . . . . . . . . . . . . . . . . . . . . . . . .52 remote control starting system...

  • Page 864

    Seat belt pretensioner . . . . . . . . . . . . . . . . . . . . .62 seat belt reminder . . . . . . . . . . . . . . . . . . . . . . .52 seat belt system . . . . . . . . . . . . . . . . . . . . . . . . .50 seat belt maintenance . . . . . . . . . . . . . . . . . . . . . .795 seat belt reminder . . . . ....

  • Page 865

    Transfer case, shifting into transfer case neutral (n) . . . . . . . . . . . . . . . . . . . . . . . . . . .676 transfer case, shifting out of transfer case neutral (n) . . . . . . . . . . . . . . . . . . . . . . . . . . .679 shift lever override . . . . . . . . . . . . . . . . . . . . . . .736 shou...

  • Page 866

    System, remote starting . . . . . . . . . . . . . . . . . . . . .34 tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .268 temperature control, automatic (atc) . . . . . . . . . .418 tilt steering column . ...

  • Page 867

    Disabled vehicle . . . . . . . . . . . . . . . . . . . . . . . .740 guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .657 recreational . . . . . . . . . . . . . . . . . . . . . . . . . . .673 weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .657 towing vehicle behi...

  • Page 868

    Passive entry programming . . . . . . . . . . . . . . . . .42 uconnect® settings . . . . . . . . . . . . . . . . . . . . . .364 uconnect® voice command. . . . . . . . . . . . . . . . . .422 uniform tire quality grades . . . . . . . . . . . . . . . . .845 universal garage door opener (homelink®) prog...

  • Page 869

    Rear sliding . . . . . . . . . . . . . . . . . . . . . . . . . . .247 reset auto-up . . . . . . . . . . . . . . . . . . . . . . . . . .48 wind buffeting . . . . . . . . . . . . . . . . . . . . . . . . . .50 windshield defroster. . . . . . . . . . . . . . . . . . . . . . .116 windshield washers . . ....

  • Page 870

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be obs...

  • Page 871

    1 5 0 0 / 2 5 0 0 / 3 5 0 0 chrysler group llc o w n e r ’ s m a n u a l 2 0 1 5 20 15 r am t ru ck 15 00 /2 50 0/ 35 00 15d241-126-aa first edition printed in u.S.A. R a m t r u c k.