1. DL manuals
  2. RAM
  3. Automobile
  4. Promaster 2014
  5. Owner's Manual

RAM Promaster 2014 Owner's Manual

Other manuals for Promaster 2014: Brochure & Specs, Supplement Manual, User Manual, Owner's Manual
Manual is about: Commercial

Summary of Promaster 2014

  • Page 1

    P r o m a s t e r chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 promaster 14vf-126-ac third edition printed in u.S.A..

  • Page 2

    Vehicles sold in canada with respect to any vehicles sold in canada, the name chrysler group llc shall be deemed to be deleted and the name chrysler canada inc. Used in substitution therefore. Driving and alcohol drunken driving is one of the most frequent causes of accidents. Your driving ability c...

  • Page 3: Table Of Contents

    Table of contents section page 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 things to know before starting your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 understanding the feat...

  • Page 5: Introduction

    Introduction contents 䡵 introduction . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 how to use this manual . . . . . . . . . . . . . .4 䡵 warnings and cautions . . . . . . . . . . . . . .6 䡵 van conversions/campers . . . . . . . . . . . .6 䡵 vehicle identification number . . . . . . . .6 䡵 vehic...

  • Page 6

    Introduction congratulations on selecting your new chrysler group llc vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This owner’s manual has been prepared with the assis- tance of service and ...

  • Page 7

    1 introduction 5.

  • Page 8

    Warnings and cautions this owners manual contains warnings against op- erating procedures that could result in a collision or bodily injury. It also contains cautions against proce- dures that could result in damage to your vehicle. If you do not read this entire owners manual, you may miss importan...

  • Page 9

    Frame and underbody as well as the automobile infor- mation disclosure label affixed to a window on your vehicle, the vehicle registration and title. Note: it is illegal to remove or alter the vin. Vehicle modifications/alterations warning! Any modifications or alterations to this vehicle could seri...

  • Page 11: Contents

    Things to know before starting your vehicle contents 䡵 a word about your keys . . . . . . . . . . . . .12 ▫ ignition key removal . . . . . . . . . . . . . . . . . . .12 ▫ locking doors with a key. . . . . . . . . . . . . . . .14 ▫ key-in-ignition reminder . . . . . . . . . . . . . . . .14 䡵 steering...

  • Page 12

    ▫ programming additional transmitters. . . . . . . .19 ▫ transmitter battery replacement . . . . . . . . . . .20 ▫ general information . . . . . . . . . . . . . . . . . . . .21 䡵 power door locks . . . . . . . . . . . . . . . . . . .21 ▫ automatic door locks — if equipped . . . . . . .23 ▫ auto unlo...

  • Page 13

    ▫ child restraints . . . . . . . . . . . . . . . . . . . . . . .52 䡵 fuel cut off switch . . . . . . . . . . . . . . . . . . . . . .60 䡵 engine break-in recommendations . . . .61 䡵 safety tips . . . . . . . . . . . . . . . . . . . . . . . . . .62 ▫ transporting passengers. . . . . . . . . . . . . . ...

  • Page 14

    A word about your keys the key fob contains the remote keyless entry (rke) transmitter with an integrated key. To use the mechanical key simply press the mechanical key release button. The vehicle is supplied with a code card containing key code numbers to order duplicate keys, and the autho- rized ...

  • Page 15

    3. Remove the key from the ignition switch lock cylinder. Warning! • before exiting a vehicle, always apply the parking brake, shift the transmission into park and re- move the key fob from the ignition. When leaving the vehicle, always lock your vehicle. • never leave children alone in a vehicle, o...

  • Page 16

    Warning! (continued) • do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. Caution! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unatt...

  • Page 17

    To release the steering wheel lock — if equipped insert the key in the ignition switch and start the engine. If the key is difficult to turn, move the wheel slightly to the right or left to disengage the lock. Note: if you turned the wheel to the right to engage the lock, you must turn the wheel sli...

  • Page 18

    Caution! (continued) • the sentry key® immobilizer system is not com- patible with some aftermarket remote starting sys- tems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the keys provided with your new vehicle have been programmed to the vehi...

  • Page 19

    Note: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Vehicle security alarm the vehicle security alarm monitors the vehicle doors and ignition for unauthorized operation. When the ve- hicle security al...

  • Page 20

    System will give you a false alarm. If one of the previ- ously described arming sequences has occurred, the vehicle security alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the vehicle secu...

  • Page 21

    To unlock the doors press and release the unlock button on rke transmit- ter once to unlock only the front doors. Press and release the cargo unlock button on rke transmitter once to unlock the cargo area (rear lateral sliding doors and rear door). The turn signal lights will flash to acknowledge th...

  • Page 22

    Transmitter battery replacement note: perchlorate material – special handling may ap- ply. See www.Dtsc.Ca.Gov/hazardouswaste/perchlorate the recommended replacement battery is cr2032. 1. Press the mechanical key release button and release the mechanical key to access the battery case screw located ...

  • Page 23

    General information this device complies with part 15 of the fcc rules and rss 210 of industry canada. Operation is subject to the following conditions: • this device may not cause harmful interference. • this device must accept any interference received, including interference that may cause undesi...

  • Page 24

    To unlock the front doors, pull the inside door handle to the first detent. If the rear doors are locked, you must pull the door handle twice to open the door. The load compartment power door lock switch is located on the driver door trim panel. Use this switch to lock or unlock the load compartment...

  • Page 25

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 26

    Note: the key off power delay feature will allow the power windows to operate for up to three minutes after the ignition is turned off. This feature is cancelled when either front door is opened. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing chil...

  • Page 27

    To open the window part way, press the window switch and release it when you want the window to stop. The power window switches remain active for up to three minutes (depending on the accessory delay setting) after the ignition switch has been turned off. Opening a vehicle front door will cancel thi...

  • Page 28

    • passenger seat belt systems include automatic lock- ing retractors (alrs), which lock the seat belt web- bing into position by extending the belt all the way out and then adjusting the belt to the desired length to restrain a child seat or secure a large item in a seat please pay close attention t...

  • Page 29

    You should read the instructions provided with your child restraint to make sure that you are using it properly. 2. All occupants should always wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the advanced front air...

  • Page 30

    Warning! (continued) • supplemental side air bag inflatable curtain (sabic) and seat-mounted side air bags (sab) also need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. • in a collision, you and your passengers can suffer much greater injuries if you...

  • Page 31

    Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. • be sure ever...

  • Page 32

    Lap/shoulder belt operating instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to...

  • Page 33

    Warning! • a belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal inju- ries. Always buckle your belt into the buckle nearest you. • a belt that is too loose will not protect you prop- erly. In a sudden stop you...

  • Page 34

    Warning! (continued) • a belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause inter- nal injuries. Ribs aren’t as strong as shoulder bones. Wear the belt over your...

  • Page 35

    Warning! • a lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • a twisted belt may not protect you properly. In a collisi...

  • Page 36

    Lap/shoulder belt untwisting procedure use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to create a fold ...

  • Page 37

    As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Automatic locking retractor (alr) mode in this mod...

  • Page 38

    How to disengage the automatic locking mode unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Warning! • the belt and retractor assembly must be replaced if the seat belt ...

  • Page 39

    Note: these devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the occupant re- straint controller (orc). Like the air bags, the preten- sioners are single use items. A deplo...

  • Page 40

    The front passenger seat beltalert® is not active when both the front passenger seats are unoccupied. Beltalert® may be triggered when an animal or heavy object is on one or both of the front passenger seats. It is recom- mended that pets be restrained in pet harnesses or pet carriers that are secur...

  • Page 41

    Note: the driver and passenger advanced front air bags are certified to the new federal regulations for advanced air bags. This vehicle is equipped with a driver and/or front passenger seat belt buckle switch that detects whether the driver or front passenger seat belt is fastened. This vehicle is e...

  • Page 42

    Note: • air bag covers may not be obvious in the interior trim, but they will open during air bag deployment. • after any collision, the vehicle should be taken to an authorized dealer immediately. Air bag system components your vehicle may be equipped with the following air bag system components: •...

  • Page 43

    Warning! • no objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • do not put anything on or around the air bag covers or attempt to open them manually. Y...

  • Page 44

    When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only. Supplemental side air bag inflatable curtain (sabic) sabic air...

  • Page 45

    • being too close to the sab and sabic air bags during deployment could cause you to be severely injured or killed. The system includes side impact sensors that are cali- brated to deploy the side air bags during impacts that require air bag occupant protection. Warning! • your vehicle is equipped w...

  • Page 46

    Always sit upright as possible with your back against the seat back, use the seat belts properly, and use the appropriate sized child restraint, infant restraint or booster seat recommended for the size and weight of the child. Knee impact bolsters the knee impact bolsters help protect the knees of ...

  • Page 47

    Impact, advanced front air bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. The side air bags will not deploy in all side collisions. Side air bag deployment will depend on the severity and type of collision. Because air bag sensors meas...

  • Page 48

    Warning! Ignoring the air bag warning light in your instru- ment panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have ...

  • Page 49

    Based on the severity and type of collision, the side air bag inflator on the crash side of the vehicle may be triggered, releasing a quantity of non-toxic gas. The inflating sab exits through the seat seam into the space between the occupant and the door. The sab fully inflate in about 10 milliseco...

  • Page 50

    If a deployment occurs the advanced front air bags are designed to deflate immediately after deployment. Note: front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or al...

  • Page 51

    Do not drive your vehicle after the air bags have de- ployed. If you are involved in another collision, the air bags will not be in place to protect you. Warning! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and th...

  • Page 52

    Warning! (continued) • do not attempt to modify any part of your air bag system. The air bag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any air bag system service. If your seat, including your trim cover and cushion,...

  • Page 53

    Note: if the speedometer, tachometer, or any engine related gauges are not working, the occupant restraint controller (orc) may also be disabled. The air bags may not be ready to inflate for your protection. Promptly check the fuse block for blown fuses. Refer to the label located on the inside of t...

  • Page 54

    In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equip- ment, can read the information if they have access to the vehicle or the edr. Child restraints everyone in your vehicle needs to be buckled up at all times, including babies and children. Ev...

  • Page 55

    Note: • for additional information, refer to www.Seatcheck.Org or call 1–866–seatcheck. Canadian residents should refer to transport canada’s website for additional infor- mation: • http://www.Tc.Gc.Ca/eng/roadsafety/safedrivers- childsafety-index-53.Htm summary of recommendations for restraining ch...

  • Page 56

    Child size, height, weight or age recommended type of child re- straint larger children children who have out-grown their forward-facing child restraint, but are too small to properly fit the vehicle’s seat belt belt positioning booster seat and the vehicle seat belt, seated in the rear seat of the ...

  • Page 57

    Old. Children should remain rearward-facing until they reach the highest weight or height allowed by their convertible child seat. Warning! • never place a rear facing infant seat in front of an air bag. A deploying passenger advanced front air bag can cause death or serious injury to a child 12 yea...

  • Page 58

    Warning! • improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. • when your child restraint...

  • Page 59

    Child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm or behind their back. Installing child restraints in commercial vehicles thi...

  • Page 60

    Into the retractor. For additional information on alr, refer to the “automatic locking mode” description un- der “occupant restraints.” front bucket seat automatic locking retractor (alr) location front bench seat automatic locking retractor (alr) locations 58 things to know before starting your veh...

  • Page 61

    Installing a child restraint with a switchable automatic locking retractor (alr) 1. Place the child seat in the center of the seating position. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-most position to make room for the child seat. You ma...

  • Page 62

    Fuel cut off switch the vehicle is fitted with a safety switch that, in the event of an accident, comes into operation by cutting off the fuel supply and turning off the engine as a consequence. When the inertia switch cuts in, this cuts off the fuel supply and also activates the hazard warning ligh...

  • Page 63

    Reactivating the fuel cut-off switch fig. 85: 1. Press the button a to reactivate the fuel cut off switch. Warning! Before reactivating the fuel cut off switch, carefully check for fuel leaks or damage to vehicle electrical devices (e.G. Headlights). Engine break-in recommendations a long break-in p...

  • Page 64

    The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to “maintenance procedures...

  • Page 65

    Exhaust gas warning! Exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (co), follow these safety tips: • do not run the engine in a closed garage or in confined...

  • Page 66

    Safety checks you should make inside the vehicle seat belts inspect the belt system periodically, checking for cuts, frays, and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Front seat belt assemblies must be replaced after a collision. Rear seat b...

  • Page 67

    Warning! Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious per- sonal injury. • always make sure that floor mats are properly attached to the floor mat fasteners. • never place or install floor mats or other floor coverings in the vehicle that cannot b...

  • Page 68

    Periodic safety checks you should make outside the vehicle tires examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks and bulges. Ch...

  • Page 69: Contents

    Understanding the features of your vehicle contents 䡵 mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 ▫ inside day/night mirror — if equipped . . . . .70 ▫ outside mirrors . . . . . . . . . . . . . . . . . . . . . . .70 ▫ outside mirrors folding feature . . . . . . . . . . .71 ▫ ...

  • Page 70

    ▫ daytime running lights — if equipped . . . . . .88 ▫ lights-on reminder . . . . . . . . . . . . . . . . . . . .88 ▫ battery saver . . . . . . . . . . . . . . . . . . . . . . . . .88 ▫ fog lights — if equipped . . . . . . . . . . . . . . . .89 ▫ turn signals . . . . . . . . . . . . . . . . . . . . ...

  • Page 71

    䡵 parksense® rear park assist — if equipped . . . . . . . . . . . . . . . . . . . . . . . . . .99 ▫ parksense® rear park assist sensors . . . . . . . .99 ▫ parksense® rear park assist alerts . . . . . . . . .100 ▫ parksense® rear park assist failure indications . . . . . . . . . . . . . . . . . . . ...

  • Page 72

    Mirrors inside day/night mirror — if equipped a two-point pivot system allows for horizontal and vertical adjustment of the mirror. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (towa...

  • Page 73

    Warning! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle...

  • Page 74

    To adjust a mirror, turn the control knob toward the left upper, left lower, right upper or right lower mirror positions indicated by one of the four arrow’s on the switch. Tilt the control wand in the direction you want the mirror to move. When you are finished adjusting the mirror, turn the contro...

  • Page 75

    Seats seats are a part of the occupant restraint system of the vehicle. Warning! • it is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • do not allow people to ride in any area of you...

  • Page 76

    Forward and rearward adjustment the adjusting bar is at the front of the seat, near the floor. Pull the bar upward to move the seat forward or rear- ward. Release the bar once the seat is in the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the se...

  • Page 77

    Height adjustment − without swivel seat the height adjusting levers are located on the center outboard side of the seat. Lift up on the front lever to adjust the front of the seat up or down. Lift up on the rear lever to adjust the rear of the seat up or down. 1 — front height adjusting lever 2 — re...

  • Page 78

    Height adjustment — with swivel seat the height adjusting knobs are located on the center outboard side of the seat. Rotate the front knob to adjust the front of the seat up or down. Rotate the rear knob to adjust the rear of the seat up or down. Recliner adjustment — without swivel seat the recline...

  • Page 79

    Seatback to its normal upright position, lean forward, rotate the knob forward until the seatback is in the upright position. Recliner adjustment — with swivel seat the recliner lever is located at the lower front outboard side of the seat. To recline the seatback, lean forward slightly, pull the le...

  • Page 80

    Warning! • adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked. • do not ride with the seatback reclined so ...

  • Page 81

    Damper weight adjustment use the weight adjustment knob to set the required setting based on body weight, with settings between 88 lbs (40 kg) and 286 lbs (130 kg). Swivel seat — if equipped the seat may be turned through 180° toward the seat on the opposite side and approximately 35° toward the doo...

  • Page 82

    Flap on bench — if equipped if your vehicle is equipped with a bench seat, the seat is equipped with a fold-down flap that can be used as a document support surface. To use the fold-down flap, grasp the pull tab and lower the flap. The fold-down flap is equipped with two cup holders and a support su...

  • Page 83

    Heated seats — if equipped on some models, the front driver and passenger seats may be equipped with heaters in both the seat cushions and seatbacks. The controls for the front heated seats are located on the lower outboard side of the seat. Press the switch once to turn on the heated seats. Press t...

  • Page 84

    Warning! (continued) • do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat. Hea...

  • Page 85

    Adjustable armrests — if equipped the seat adjustable armrest can be raised and adjusted for height. Underneath the front of the armrest is the adjuster wheel which will adjust the height of the armrest up or down. Turn the adjuster wheel to the right or left to adjust the height of the armrest up o...

  • Page 86

    To open and close the hood to open the hood, two latches must be released. 1. Open the drivers door to gain access to the hood release lever. Pull the hood release lever located on the side of the instrument panel. Adjuster wheel hood release 84 understanding the features of your vehicle.

  • Page 87

    2. Move to the outside of the vehicle, reach into the opening beneath the center of the hood and push the safety latch lever to the right to release it, before raising the hood. 3. Raise the hood and place the hood prop rod in hood slot to secure the hood in the open position. Caution! To prevent po...

  • Page 88

    Warning! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. Lights multifunction lever the multifunction lever cont...

  • Page 89

    Headlights to turn on the headlights, turn the end of the multifunction lever to the headlight position. When the headlight switch is on, the parking lights, taillights, license plate light, the clear- ance lights and instrument panel lights are also turned on. To turn off the headlights, turn the e...

  • Page 90

    Daytime running lights — if equipped note: when the headlights are turned on, the daytime running lights will be deactivated. To activate the daytime running lights (drl), rotate the end of the multifunction lever to the o (off) position. Note: the low beams and side/taillights will not be on with d...

  • Page 91

    Fog lights — if equipped the fog light switch is located on the center stack of the instrument panel, just below the climate controls. Press the switch once to turn the fog lights on. Press the switch a second time to turn the fog lights off. Turn signals move the multifunction lever up or down and ...

  • Page 92

    Flash-to-pass you can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released. Follow me home/headlight delay when this feature is selected the driver can cho...

  • Page 93

    Left switch • press the left switch to the left to turn off the auto dome lights. The dome lights will not automatically turn on when a door is opened. • press the left switch to the right to turn on the dome lights. Right switch • press the right switch to the left to turn on the left map light. • ...

  • Page 94

    Windshield wipers and washers windshield wipers the windshield wiper/washer lever is located on the right side of the steering column. There are five different modes of operation for the front windshield wipers. The windshield wiper lever can be raised or lowered to access the modes. Note: the winds...

  • Page 95

    Low speed push the lever downward to the second detent. The wipers will operate at low speed. High speed push the lever downward to the third detent. The wipers will operate at high speed. Mist feature use the mist feature when weather conditions make occasional usage of the wipers necessary. Push t...

  • Page 96

    Telescoping steering column this feature allows you to lengthen or shorten the steering column. The telescoping control handle is lo- cated below the steering wheel at the end of the steering column. To unlock the steering column, pull the control handle up. To lengthen or shorten the steering colum...

  • Page 97

    Electronic speed control when engaged, the electronic speed control takes over accelerator operations at speeds greater than 25 mph (40 km/h) up to the maximum speed of 100 mph (160 km/h). The electronic speed control lever is located on the left side of the steering column. Electronic speed control...

  • Page 98

    Note: in order to ensure proper operation, the elec- tronic speed control system has been designed to shut down if multiple speed control functions are operated at the same time. If this occurs, the electronic speed control system can be reactivated by rotating the electronic speed control on/off ce...

  • Page 99

    To deactivate a soft tap on the brake pedal, pushing the res button, or normal brake pressure while slowing the vehicle will deactivate electronic speed control without erasing the set speed memory. Rotating the center ring upward to turn the system off or turning the ignition switch off erases the ...

  • Page 100

    To decrease speed when the electronic speed control is set, you can de- crease speed by tapping the speed control lever down (-). The speed decrement shown is dependant on the speed of u.S. (mph) or metric (km/h) units: u.S. Speed (mph) • tapping the speed control lever down (-) once will result in ...

  • Page 101

    On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without electronic speed control. Warning! Electronic speed control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose cont...

  • Page 102

    From the center of the rear fascia/bumper and up to 24 in (60 cm) from the corners of the rear fascia/bumper, depending on the location, type and orientation of the obstacle. If several obstacles are detected, the parksense® rear park assist system indicates the nearest obstacle. The minimum height ...

  • Page 103

    Audible and visual signals supplied by the parksense® rear park assist system signal meaning indication obstacle distance an obstacle is present within the sensors’ field of view audible signal (dashboard loud- speaker) • sound pulses emitted at a rate that increases as the distance de- creases. • e...

  • Page 104

    While audible signals are emitted, the audio system is not muted. The audible signal is turned off immediately if the distance increases. The tone cycle remains constant if the distance measured by the inner sensors is constant. If this condition occurs for the external sensors, the signal is turned...

  • Page 105

    Parksense® rear park assist system usage precautions note: • ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the rear park assist system operating properly. • jackhammers, large trucks, and other vibrations co...

  • Page 106

    Caution! (continued) • the vehicle must be driven slowly when using parksense® in order to be able to stop in time when an obstacle is detected. It is recommended that the driver looks over his/her shoulder when using parksense®. Warning! • drivers must be careful when backing up even when using par...

  • Page 107

    Parkview® rear back up camera — if equipped your vehicle may be equipped with the parkview® rear back up camera that allows you to see an on-screen image of the rear surroundings of your vehicle whenever the shift lever is put into reverse. The image will be displayed on the touchscreen display alon...

  • Page 108

    When displayed, static grid lines will illustrate the width of the vehicle and will show separate zones that will help indicate the distance to the rear of the vehicle. The following table shows the approximate distances for each zone: zone distance to the rear of the vehicle red 0 - 1 ft (0 - 30 cm...

  • Page 109

    Caution! (continued) • to avoid vehicle damage, the vehicle must be driven slowly when using parkview® to be able to stop in time when an obstacle is seen. It is recom- mended that the driver look frequently over his/her shoulder when using parkview®. Note: if snow, ice, mud, or any foreign substanc...

  • Page 110

    Power outlets — if equipped passenger compartment power outlet the cigar lighter and the power socket are located in the center console. It only operates with the ignition key at mar/on. Map/dome lights 1 — auto/off 3 — left map 2 — dome 4 — right map passenger compartment power socket 108 understan...

  • Page 111

    Load compartment power outlet the load compartment power outlet is located on the left rear side of the rear cargo compartment. The outlet can be is used for powering 12 volt adaptive accessories and recharging communications devices. Note: do not connect devices with power higher than 180 w to the ...

  • Page 112

    Warning! To avoid serious injury or death: • only devices designed for use in this type of outlet should be inserted into any 12 volt outlet. • do not touch with wet hands. • close the lid when not in use and while driving the vehicle. • if this outlet is mishandled, it may cause an electric shock a...

  • Page 113

    Cigar lighter and ash receiver — if equipped a removable ash receiver and cigar lighter are available. Cupholders the cupholders for the drivers and passenger area are located near the floor just under the center stack storage compartment. There are cupholders located in each door panel as well as o...

  • Page 114

    Storage glove compartments the glove compartments are located on the right side of the instrument panel. 1 — upper glove compartment 2 — lower glove compartment 112 understanding the features of your vehicle.

  • Page 115

    Front door storage — if equipped storage areas and bottle holders are located in both the front door trim panels. Center storage— if equipped the center storage bin is located in the lower center of the instrument panel just below the climate controls and above the cupholders. Also there are storage...

  • Page 116

    Dashboard clipboard located on top of the dashboard is a clipboard and two storage bins on each side of the clipboard. Cargo area features cargo area the cargo area may be equipped with different options such as a optional side panels, rear seats and an optional floor. Clipboard and storage bins 114...

  • Page 117: Contents

    Understanding your instrument panel contents 䡵 instrument panel features . . . . . . . . . .117 䡵 instrument cluster . . . . . . . . . . . . . . . . .119 䡵 instrument cluster descriptions . . . . .120 䡵 electronic vehicle information center (evic) . . . . . . . . . . . . . . . . . . . . . . . .133 ▫...

  • Page 118

    ▫ uconnect® rh3 display. . . . . . . . . . . . . . . . .146 ▫ general functions and settings . . . . . . . . . . .147 ▫ tuner mode (am/fm radio) . . . . . . . . . . . . .150 ▫ setup menu . . . . . . . . . . . . . . . . . . . . . . . . .153 ▫ clock . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Page 119

    Instrument panel features 4 understanding your instrument panel 117.

  • Page 120

    1 — air outlet 10 — glove compartment 19 — uconnect® phone buttons 2 — multifunction lever (external lights) 11 — cup holder 20 — release lever column 3 — instrument cluster 12 — usb charger/12v 21 — horn 4 — multifunction lever (front/ rear wiper, trip computer) 13 — climate controls 22 — mute/ucon...

  • Page 121

    Instrument cluster 4 understanding your instrument panel 119.

  • Page 122

    Instrument cluster descriptions 1. Speedometer the speedometer shows the vehicle speed in miles per hour and/or kilometers per hour (mph/km/h). 2. Turn signal indicators the arrow will flash with the exterior turn signal when the turn signal lever is operated. Note: • a continuous chime will sound i...

  • Page 123

    Note: if the driver’s door is open, and the headlights or park lights are left on, the high beam indicator light will remain illuminated and a chime will sound until lights have been turned to the off position. 6. Park/headlight on indicator — if equipped this indicator will illuminate when the park...

  • Page 124

    8. External light failure indicator — if equipped the external light failure indicator will come on when a failure to one of the following lights is detected: • side marker lights • brake lights • direction indicators • backup lights • parking lights • headlights • tail lights • d.R.L. • clearance l...

  • Page 125

    11. Tachometer the tachometer indicates engine speed in revolutions per minute (rpm x 1000). Caution! Do not operate the engine with the tachometer pointer in the red area. Engine damage will occur. Caution! Do not operate the engine with the tachometer pointer at high rpm for extended periods. Engi...

  • Page 126

    Briefly as a bulb check. If the charging system light remains on, or comes on while driving, it means that the vehicle is experiencing a problem with the charging system. Obtain service immediately. See your au- thorized dealer. If jump starting is required, refer to “jump starting procedures” in “w...

  • Page 127

    Warning! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the abs are also equipped with electronic brake force distr...

  • Page 128

    If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service. Although your vehicle will usually be drivable and not need towing, see your authorized dealer for service as soon as possible. Caution! Prolonged driving with the mal...

  • Page 129

    Caution! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “h” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “h” and you hear cont...

  • Page 130

    Service. Refer to “if your engine overheats” in “what to do in emergencies” for further information. 19. Electronic throttle control (etc) light this light informs you of a problem with the electronic throttle control (etc) system. If a problem is detected, the light will come on while the engine is...

  • Page 131

    23. Generic warning light the generic warning light will illuminate if any of the following conditions occur: • air bag warning light fault • engine oil pressure sensor failure • fuel cut-off intervention • parking sensor failure 24. Air bag warning light this light will turn on for four to eight se...

  • Page 132

    Accordingly, when the low tire pressure telltale illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fue...

  • Page 133

    Caution! (continued) equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can or balance beads if your vehic...

  • Page 134

    Engine running. If the “esc activation/malfunction in- dicator light” comes on continuously with the engine running, a malfunction has been detected in the esc system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater...

  • Page 135

    30. Vehicle security light if during starting, the key code is not correctly recognized, the vehicle security light comes on in the instrument panel. In this case, turn the key to off and then to on/run; if it is still locked, try again with the other keys that come with the vehicle. Contact an auth...

  • Page 136

    • trip functions • date • time the system allows the driver to select information by pressing the following buttons mounted on the instru- ment panel to the left of the steering column: • mode button press and release the mode button to access/select the information screens or sub-menu screens of a ...

  • Page 137

    • up arrow button press and release the up arrow button to scroll upward through the main menu and sub- menus or adjust the illumination on the instru- ment panel when the headlights are on. • down arrow button press and release the down arrow button to scroll downward through the main menu and sub-...

  • Page 138

    • service • passenger air bag — if equipped note: if equipped with uconnect® 5.0, some customer programmable features will display in the uconnect® 5.0 system. Refer to uconnect® 5.0 for further information. Selecting an option of the main menu without sub- menu 1. Briefly press the mode button to s...

  • Page 139

    Change engine oil indicator system change engine oil your vehicle is equipped with an engine oil change indicator system. The “change engine oil” message will display in the evic display. The engine oil change indicator system is duty cycle based, which means the engine oil change interval may fluct...

  • Page 140

    • a long button press resets the system and then starts a new trip. New trip to reset: • press and hold the trip button to reset the system manually. • when the “trip distance” reaches 99999.9 miles or kilometers or when the “travel time” reaches 999.59 (999 hours and 59 minutes), the system is rese...

  • Page 141

    • trip distance a • average consumption a • instantaneous consumption • average speed a • travel time a (driving time) “trip b” can be used to display the figures relating to: • trip distance b • average consumption b • average speed b • travel time b (driving time) note: “trip b” functions may be e...

  • Page 142

    Distance traveled this value shows the distance covered since the last reset. Average consumption this value shows the approximate average consumption since the last reset. Instant consumption this indicates the fuel consumption. The value is con- stantly updated. The message “----” will appear on t...

  • Page 143

    Note: the setting can be increased or decreased by 5 mph or km/h each time the up/down button is pressed for speed settings above 20 mph (32 km/h). To increase or decrease the set speed rapidly, press and hold the up/down button. Save the setting by briefly press- ing the button when you approach th...

  • Page 144

    3. Briefly press the mode button to go back to the menu screen, or press and hold the mode button (approxi- mately one second) to go back to the main screen without storing the settings. Exit menu this function closes the initial menu screen. Briefly press the mode button to go back to the main scre...

  • Page 145

    Recommendations road safety we recommend that you learn how to use the various radio features (for example, station preset) before you begin your journey. Warning! Turning the volume up too high may be dangerous for the driver and other people on the road. You should adjust the volume so that you ar...

  • Page 146

    Identification number the radio has a unique identification number (found on the warranty card). This card is required as proof of ownership if the radio is stolen or when seeking assis- tance. Do not store the warranty card in the vehicle. Security code this radio has a serial number (found on the ...

  • Page 147

    Action display press 䉳䉳 or 䉴䉴 to move to the fourth digit. 4 3 5 0 turn the rotary knob to select the fourth digit 4 3 5 9 when you finish entering the code, press the rotary knob to accept the code entered. 4 3 5 9 if you enter the correct code, the radio will start as normal in radio mode (tuner)....

  • Page 148

    General • separate bass and treble settings • balance/fade (balances left/right and front/rear channels) • equalizer • loudness • digital clock in 24-hour format with weekday setting • illuminated buttons and display • lcd display • extended functions field (setup menu) allows you to change the defa...

  • Page 149

    Description of commands rotary knob: turn radio on and off, volume, forward/ reverse track, confirm selected option. 䉴䉴 and 䉳䉳 buttons: station search in automatic mode, station search in manual mode, forward/reverse tracks, forward/reverse within track. Mute/pause button: interrupts the sound by mu...

  • Page 150

    Turned off, the radio will display the message ⬙ 60 min ⬙ for three seconds and switch off automatically after 60 minutes if no buttons are pressed. If you prefer, you can set ⬙ auto switch ⬙ to ⬙ on ⬙ (see setup menu section). The radio will then follow two parameters: ignition and previous state. ...

  • Page 151

    Bass the display will show ⬙ bass 00 ⬙ to indicate that the bass function can be set. To increase the bass level, turn the rotary knob clockwise. To decrease the bass level, turn the rotary knob counterclockwise. The bass levels can be set between -15 and 15. Treble the display will show ⬙ treb 00 ⬙...

  • Page 152

    Volume turn the rotary knob clockwise to increase the vol- ume. Turning it counterclockwise will lower the volume. The volume can be set between 0 and 30. Tuner mode (am/fm radio) when you enter tuner mode, the radio tunes to the most recently selected station and will remain on the most recently se...

  • Page 153

    Selected band (100 khz for fm and 10k hz for am). When the search button is pressed and held, the radio station frequency will continue to be increased or de- creased. If the buttons are not pressed for five seconds, the display will show the message ⬙ auto ⬙ and manual search mode will be canceled....

  • Page 154

    Accessing preset stations when the preset buttons (1 through 6) are pressed for less than two seconds the radio will tune in to the station associated with that particular memory location. The display shows the preset number and frequency of the associated station for three seconds. The display will...

  • Page 155

    Setup menu you can use the setup menu to change the various factory settings to suit your own preferences. Press menu to activate the maximum volume function. Repeatedly pressing this button will activate the other functions in the following sequence: maximum volume (mvol) auto switch (auto) beep (b...

  • Page 156

    Clock pressing the disp button for more than two seconds enables or disables the clock display. When this feature is enabled, the display shows ⬙ clk on ⬙ and the clock is displayed whenever the ignition is switched on, even if the radio is off. This function takes priority in the display whenever y...

  • Page 157

    To enter usb mode, you must press the src button. When you enter usb mode, the display shows ⬙ load- ing ⬙ while the radio checks whether the connected device is valid. If there is no usb device, an invalid usb device, or a valid device that is defective, the display will show ⬙ err usb ⬙ for two se...

  • Page 158

    156 understanding your instrument panel.

  • Page 159

    Play sequence (file) comments 1 track 1_1 if there are mp3, wma or aac (extensions mp3, wma, m4a, mp4 and 3gp) files in the root folder, these will be played first. 2 track 2_1 folders within the same level are sorted in ascending order by name (up to folder number 100, after which the order follows...

  • Page 160

    When these buttons are pressed, the display will show a ⬙ trkyyy ⬙ message, where yyy is the track number. If any of these buttons is briefly pressed again, the number in the display will continue changing according to the selected track. While the track is being selected, that is, when or are press...

  • Page 161

    Press this button again to resume music playback from the point where it left off, without changing the original volume level. The display will show ⬙ play ⬙ for three seconds. It then returns to the previous mode. When or , audio, 1, 2, and src are pressed in ⬙ mute/paused ⬙ mode, playback (where a...

  • Page 162

    When the radio skips from one folder to another, the display will show the name of the folder to which you are moving for a few milliseconds (the rotary movements are ignored during this period) and a maximum of three seconds. When you reach the final track in the last folder and turn the rotary kno...

  • Page 163

    Usb device. When you reach the first folder and press button 2 again, the radio will advance to the next folder on the usb device. Shuffle (random playback) pressing the rnd button enables or disables the ⬙ shuffle ⬙ feature. When enabled, the rnd indicator is switched on and the display will show ⬙...

  • Page 164

    • bit rate 8 to 320 kbps, supports variable bit rate (vbr) • id3tag v1.0, v1.1, v2.2, v2.3 and v2.4. • extension: mp3 decoding wma files: • supports windows media audio 9 standard. • does not support drm. • supports the following sample rates: 8k, 16k, 32k, 11.025k, 22.05k, 44.1k, 12k, 24k and 48 kh...

  • Page 165

    • maximum operating voltage: 18 v per hour. • quiescent current (@12.6 v): 2.2 ma (radio off, ignition off). • maximum current in operation: 10a. Uconnect® settings the uconnect® system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access a...

  • Page 166

    Hard-keys hard-keys are located below the uconnect® system in the center of the instrument panel. In addition, there is a scroll/enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.E., 30, 60, 90), press the center of the control knob on...

  • Page 167

    Settings screen. Pressing the up or down arrow soft-keys on the right side of the screen will allow you to toggle up or down through the available settings. Clock & date after pressing the clock soft-key the following settings will be available: • time and format when in this display, you may set th...

  • Page 168

    Process, the rear view image shall not be displayed for more than five seconds and the navigation or audio screen appears again. • parkview® backup camera static gridlines your vehicle may be equipped with the parkview® rear back up camera static guidelines that allows you to see straight grid line ...

  • Page 169

    Vehicle is shifted out of reverse (with camera delay turned on), the rear view image with dynamic grid lines will be displayed for up to 10 seconds after shifting out of “reverse” unless the forward vehicle speed exceeds 8 mph (12 km/h), the transmission is shifted into “park” or the ignition is swi...

  • Page 170

    Indicating that the setting has been selected. Touch the arrow back/done soft-key to return to the previous menu. • headlight sensitivity when this feature is selected, the headlights will auto- matically remain on for a predetermined amount of time after the engine is shut off. To make your selecti...

  • Page 171

    • equalizer when in this display you may adjust the bass, mid and treble settings. Adjust the settings with the + and – setting soft-keys or by selecting any point on the scale between the + and – soft-keys. Then touch the arrow back/done soft-key. Note: bass/mid/treble allow you to simply slide you...

  • Page 172

    Phone/bluetooth® after pressing the “phone/bluetooth” soft-key the fol- lowing settings will be available: • paired devices this feature shows which phones are paired to the phone/bluetooth® system. For further information, refer to your uconnect® supplement manual. Siriusxm setup after pressing the...

  • Page 173

    Restore settings after pressing the restore settings soft-key the following settings will be available: • restore settings when this feature is selected it will reset display, clock, audio, and radio settings to their default. To restore the settings to their default setting touch the yes or no soft...

  • Page 174

    Ipod® control supports mini, 4g, photo, nano, 5g ipod® and iphone® devices. Some ipod® software versions may not fully support the ipod® control features. Please visit apple’s website for software updates. For further information, refer to the uconnect® supple- ment manual. Usb charging port the usb...

  • Page 175

    Note: if the device battery to be charged is completely depleted, it may take awhile to charge. Warning! Do not plug in or remove the ipod® or external device while driving. Failure to follow this warning could result in a collision. Steering wheel audio controls the remote sound system controls are...

  • Page 176

    The right-hand control is a rocker-type switch and con- trols the scan functions of the sound system. The left-hand control is a rocker-type switch and controls the volume of the sound system plus a button to mute the sound system. The following describes the right-hand control operation in each mod...

  • Page 177

    3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or anti-static sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may become ...

  • Page 178

    Climate controls manual heating and air conditioning the manual temperature controls consist of a series of three outer rotary dials (blower speed, temperature and mode) and three inner push buttons (recirculation, a/c, rear window defroster). Blower control rotate this control to regulate the amoun...

  • Page 179

    Temperature control rotate this control to regulate the tem- perature of the air inside the passenger compartment. Rotating the dial left into the blue area of the scale indicates cooler temperatures, while rotating right into the red area indicates warmer temperatures. Note: if your air conditionin...

  • Page 180

    • bi-level air is directed through the panel and floor outlets. Note: for all settings, except full cold or full hot, there is a difference in temperature between the upper and lower outlets. The warmer air flows to the floor outlets. This feature gives improved comfort during sunny but cool conditi...

  • Page 181

    • the use of the recirculation mode in cold or damp weather will cause windows to fog on the inside, because of moisture buildup inside the vehicle. Select the outside air position for maximum defogging. • recirculated air is not allowed in defrost modes. If the recirculation button is pressed while...

  • Page 182

    • economy mode if economy mode is desired, press the a/c button to turn off the indicator light and the a/c compressor. Then, select panel, bi-level or floor mode and move the temperature control to the desired temperature. Rear window defrosting press the rear defrost button to activate heated rear...

  • Page 183: Starting And Operating

    Starting and operating contents 䡵 starting procedures . . . . . . . . . . . . . . . .184 ▫ automatic transmission — if equipped . . . . .184 ▫ normal starting. . . . . . . . . . . . . . . . . . . . . . .184 ▫ extreme cold weather (below –20°f or −29°c) . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 184

    䡵 parking brake . . . . . . . . . . . . . . . . . . . . . .203 䡵 brake system . . . . . . . . . . . . . . . . . . . . . . .205 ▫ four-wheel anti-lock brake system (abs) . . .205 䡵 electronic brake control system . . . .207 ▫ traction control system (tcs) . . . . . . . . . . . .207 ▫ brake assist sys...

  • Page 185

    䡵 tire chains (traction devices) . . . . . . .239 䡵 tire rotation recommendations . . . . .240 䡵 tire pressure monitoring system (tpms) . . . . . . . . . . . . . . . . . . . . . . .241 ▫ base system . . . . . . . . . . . . . . . . . . . . . . . . .244 ▫ general information . . . . . . . . . . . . . ...

  • Page 186

    Starting procedures before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. Warning! • never leave children alone in a vehicle, or with access to an unlocked vehicle. • allowing children to be in a vehicle unattended is dangerous for a numb...

  • Page 187

    Extreme cold weather (below –20°f or −29°c) to ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- able from your authorized dealer) is recommended. If engine fails to start warning! Never pour fuel or other flammable liquids into the thr...

  • Page 188

    Engine block heater — if equipped the engine block heater warms the engine, and permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt ac electrical outlet with a grounded, three-wire extension cord. The engine block heater must be plugged in at least one hour to have an...

  • Page 189

    Warning! • it is dangerous to shift out of park or neutral if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit someone or something. Only shift ...

  • Page 190

    Warning! (continued) • never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking bra...

  • Page 191

    Six-speed automatic transmission the transmission gear position display (located in the instrument cluster) indicates the transmission gear range. You must press the brake pedal to move the shift lever out of park (refer to “brake/transmission shift inter- lock system” in this section). To drive, mo...

  • Page 192

    The transmission shift lever has park, reverse, neu- tral, drive, and electronic range select (ers) shift positions. Manual downshifts can be made using the ers shift control (refer to “electronic range select (ers) operation” in this section for further information). Mov- ing the shift lever into t...

  • Page 193

    The transmission locking mechanism may make it diffi- cult to move the shift lever out of park. As an added precaution, turn the front wheels toward the curb on a downhill grade, and away from the curb on an uphill grade. Warning! • never use the park position as a substitute for the parking brake. ...

  • Page 194

    Warning! (continued) • unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into park turn the engine off, and re...

  • Page 195

    • look at the transmission gear position display and verify that it indicates the park position. • with the brake pedal released, verify the shift lever will not move out of park. Caution! • before moving the shift lever out of park, you must turn the ignition switch from the lock/off position to th...

  • Page 196

    Caution! Towing the vehicle, coasting, or driving for any other reason with the transmission in neutral can cause severe transmission damage. Refer to “recreational towing” in “starting and operating” and “towing a disabled vehicle” in “what to do in emergencies” for further information. Drive (d) t...

  • Page 197

    Limited to third gear only. Normal operation will resume once the transmission temperature has risen to a suitable level. Transmission limp home mode transmission function is monitored electronically for abnormal conditions. If a condition is detected that could result in transmission damage, transm...

  • Page 198

    Electronic range select (ers) operation the electronic range select (ers) shift control allows the driver to limit the highest available gear. For example, if you shift the transmission into 3 (third gear), the trans- mission will not shift above third gear (except to prevent engine overspeed), but ...

  • Page 199

    Note: to select the proper gear position for maximum deceleration (engine braking), tap the shift lever forward (-) repeatedly as the vehicle slows. The transmission will shift to the range from which the vehicle can best be slowed down. Overdrive operation the automatic transmission includes an ele...

  • Page 200

    Torque converter clutch a feature designed to improve fuel economy has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation i...

  • Page 201

    Traction when driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observ...

  • Page 202

    Shallow standing water although your vehicle is capable of driving through shallow standing water, consider the following cautions and warnings before doing so. Warning! • driving through standing water limits your vehi- cle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through ...

  • Page 203

    Caution! (continued) • driving through standing water may cause damage to your vehicle’s drivetrain components. Always inspect your vehicle’s fluids (i.E., engine oil, trans- mission, axle, etc.) for signs of contamination (i.E., fluid that is milky or foamy in appearance) after driving through stan...

  • Page 204

    • upon initial start-up in cold weather, the power steer- ing pump may make noise for a short amount of time. This is due to the cold, thick fluid in the steering system. This noise should be considered normal, and it does not in any way damage the steering system. Caution! Prolonged operation of th...

  • Page 205

    If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for further informa- tion. Parking brake before leaving the vehicle, make sure that the parki...

  • Page 206

    When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. Warning! • never leave children alone in a vehicle, or with access to ...

  • Page 207

    Caution! If the brake warning light remains on with the parking brake released, a brake system malfunction is indicated. Have the brake system serviced by an authorized dealer immediately. Brake system in the event power assist is lost for any reason (for example; repeated brake applications with th...

  • Page 208

    The ignition off and on again may reset the abs if the fault detected was only momentary. Warning! • pumping the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow dow...

  • Page 209

    Electronic brake control system your vehicle is equipped with an advanced electronic brake control system that includes the traction control system (tcs), brake assist system (bas) and electronic stability control (esc), trailer sway control (tsc), and hill start assist (hsa). These systems compleme...

  • Page 210

    Warning! (continued) • the tcs cannot prevent collisions, including those resulting from excessive speed in turns, or hydro- planing. • the capabilities of a tcs-equipped vehicle must never be exploited in a reckless or dangerous manner, which could jeopardize the user’s safety or the safety of othe...

  • Page 211

    Electronic stability control (esc) the electronic stability control (esc) enhances direc- tional control and stability of the vehicle under various driving conditions. Esc corrects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counteracting the ov...

  • Page 212

    Esc operating modes the “esc off” switch is located in the center switch bank, next to the hazard flasher switch. Esc on this mode is the normal operating mode for esc equipped vehicles. Whenever the vehicle is started, the esc system will be in this mode. This mode should be used for most driving s...

  • Page 213

    Warning! • when in ⴖ partial off ⴖ mode, the tcs functionality of esc, (except for the limited slip feature de- scribed in the tcs section), has been disabled and the ⴖ esc off indicator light ⴖ will be illuminated. When in ⴖ partial off ⴖ mode, the engine power reduction feature of tcs is disabled,...

  • Page 214

    Light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- rized dealer as soon as possible to have the problem diagnosed and corrected. The “esc activation/malfunction indicator light” (lo- cate...

  • Page 215

    Trailer sway control (tsc) tsc uses sensors in the vehicle to recognize an exces- sively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appro- priate wheel(s) to counteract the sway of the trailer. Tsc ...

  • Page 216

    Hsa activation criteria the following criteria must be met in order for hsa to activate: • vehicle must be stopped. • vehicle must be on a 6% (approximate) grade or greater hill. • gear selection matches vehicle uphill direction (i.E., vehicle facing uphill is in forward gear; vehicle back- ing uphi...

  • Page 217

    Warning! • if you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision w...

  • Page 218

    Tire safety information tire markings note: • p (passenger) - metric tire sizing is based on u.S. Design standards. P-metric tires have the letter “p” molded into the sidewall preceding the size designa- tion. Example: p215/65r15 95h. • european-metric tire sizing is based on european design standar...

  • Page 219

    • temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- pact spare tires have the letter “t” or “s” molded into the sidewall preceding the size designation. Example: t145/80d18 103m. • high flotation tire sizing is based on u.S. Design standards and it beg...

  • Page 220

    Example: 65 = aspect ratio in percent (%) — ratio of section height to section width of tire 10.5 = section width in inches (in) r = construction code — ⬙ r ⬙ means radial construction — ⬙ d ⬙ means diagonal or bias construction 15 = rim diameter in inches (in) service description: 95 = load index —...

  • Page 221

    Example: load identification: ⴖ ....Blank.... ⴖ = absence of any text on the sidewall of the tire indicates a standard load (sl) tire extra load (xl) = extra load (or reinforced) tire light load (ll) = light load tire c, d, e, f, g = load range associated with the maximum load a tire can carry at a ...

  • Page 222

    Example: dot ma l9 abcd 0301 dot = department of transportation — this symbol certifies that the tire is in compliance with the u.S. Department of transportation tire safety standards and is approved for highway use ma = code representing the tire manufacturing location (two digits) l9 = code repres...

  • Page 223

    Tire terminology and definitions term definition b-pillar the vehicle b-pillar is the structural member of the body located behind the front door. Cold tire inflation pressure cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or ...

  • Page 224

    Tire loading and tire pressure tire and loading information placard location note: the proper cold tire inflation pressure is listed on the driver’s side b-pillar or the rear edge of the driver’s side door. B-pillar location for tire and loading information placard 222 starting and operating.

  • Page 225

    Tire and loading information placard this placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires. ...

  • Page 226

    Loading the vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the tire and loading informati...

  • Page 227

    3. Subtract the combined weight of the driver and pas- sengers from xxx lbs or xxx kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if “xxx” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the ...

  • Page 228

    226 starting and operating.

  • Page 229

    Warning! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. Tires — general information tire pressure proper tire inflation pressur...

  • Page 230

    Warning! (continued) • unequal tire pressures from one side of the vehicle to the other can cause the vehicle to drift to the right or left. • always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy improper inflation pressures can cause uneven wear patterns t...

  • Page 231

    Judgement when determining proper inflation. Tires may look properly inflated even when they are under- inflated. • inspect tires for signs of tire wear or visible damage. Caution! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and ...

  • Page 232

    Tire pressures for high speed operation the manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure ...

  • Page 233

    Consult an authorized tire dealer for tire repairs and additional information. Damaged run flat tires, or run flat tires that have experienced a loss of pressure should be replaced imme- diately with another run flat tire of identical size and service description (load index and speed code). Tire ty...

  • Page 234

    If you need snow tires, select tires equivalent in size and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the safety and handling of your vehicle. Snow tires generally have lower speed ratings than what was originally equipped with y...

  • Page 235

    Spare tires — if equipped note: for vehicles equipped with tirefit instead of a spare tire, please refer to “tirefit kit” in “what to do in emergencies” for further information. Caution! Because of the reduced ground clearance, do not take your vehicle through an automatic car wash with a compact, f...

  • Page 236

    Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare tire. Do not install more than one compact spare tire and wheel on the vehicle at any given time. Warning! Compact spares are for temporary ...

  • Page 237

    Warning! Limited-use spares are for emergency use only. In- stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your tire and loading inf...

  • Page 238

    These indicators are molded into the bottom of the tread grooves. They will appear as bands when the tread depth becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer to “replacement tires” in this section for further infor- mation. Life of t...

  • Page 239

    Warning! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Keep dismounted tires in a cool, dry place with...

  • Page 240

    It is recommended you contact your authorized tire dealer or original equipment dealer with any questions you may have on tire specifications or capability. Failure to use equivalent replacement tires may adversely affect the safety, handling, and ride of your vehicle. Warning! • do not use a tire, ...

  • Page 241

    Tire chains (traction devices) use of traction devices require sufficient tire-to-body clearance. Follow these recommendations to guard against damage. • traction device must be of proper size for the tire, as recommended by the traction device manufacturer. • install on front tires only • tire chai...

  • Page 242

    Caution! (continued) • observe the traction device manufacturer’s instruc- tions on the method of installation, operating speed, and conditions for use. Always use the suggested operating speed of the device manufac- turer’s if it is less than 30 mph (48 km/h). • do not use traction devices on a com...

  • Page 243

    Tire pressure monitoring system (tpms) the tire pressure monitor system (tpms) will warn the driver of a low tire pressure based on the vehicle recom- mended cold tire pressure. The tire pressure will vary with temperature by about 1 psi (7 kpa) for every 12° f (6.5° c). This means that when the out...

  • Page 244

    The tpms will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning limit for any reason, including low temperature effects, or natural pressure loss through the tire. The tpms will continue to warn the driver of low tire pressure as long as the condition e...

  • Page 245

    Caution! • the tpms has been optimized for the original equipment tires and wheels. Tpms pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, ...

  • Page 246

    Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • the tpms is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if un...

  • Page 247

    Display when one or more of the four active road tire pressures are low. Should this occur, you should stop as soon as possible, check the inflation pressure of each tire on your vehicle, and inflate each tire to the vehicle’s recommended cold placard pressure value. The system will automatically up...

  • Page 248

    2. If you install the spare tire in place of a road tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will sound and the tire pressure monitoring telltale light will still turn on due to the low tire. 3. However, after driving the vehicle for up...

  • Page 249

    Fuel requirements 3.6l engine this engine is designed to meet all emis- sions regulations and provide excellent fuel economy and performance when us- ing high-quality unleaded “regular” gaso- line having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide a...

  • Page 250

    Gasoline/oxygenate blends some fuel suppliers blend unleaded gasoline with oxy- genates such as ethanol. Fuels blended with oxygenates may be used in your vehicle. Caution! Do not use gasoline containing methanol or gaso- line containing more than 10% ethanol. Use of these blends may result in start...

  • Page 251

    To fix a non-ffv vehicle inadvertently fueled once with e-85 perform the following: • drain the fuel tank (see your authorized dealer). • change the engine oil and oil filter. • disconnect and reconnect the battery to reset the engine controller memory. More extensive repairs will be required for pr...

  • Page 252

    Fuel system cautions caution! Follow these guidelines to maintain your vehicle’s performance: • the use of leaded gas is prohibited by federal law. Using leaded gasoline can impair engine perfor- mance and damage the emissions control system. • an out-of-tune engine or certain fuel or ignition malfu...

  • Page 253

    Carbon monoxide warnings warning! Carbon monoxide (co) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such...

  • Page 254

    Caution! • damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system and may cause the “malfunction indicator light (mil)” to turn on, due to fuel vapors escaping from ...

  • Page 255

    Warning! (continued) • never add fuel when the engine is running. This is in violation of most state and federal fire regula- tions and may cause the mil to turn on. • a fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas...

  • Page 256

    Vehicle loading as required by national highway traffic safety admin- istration regulations, your vehicle has a certification label affixed to the driver’s side door or b-pillar. If seats are removed for carrying cargo, do not exceed the specified gvwr and gawr. Vehicle certification label your vehi...

  • Page 257

    Warning! Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front or rear gawr. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have a collision. Tire size the tire size on the vehicle certif...

  • Page 258

    The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for operation. Weigh it on a commercial scale to ensure that it is not over the gvwr. Figure out the weight on the front and rear of the vehicle separately. It is important that you distribut...

  • Page 259

    Common towing definitions the following trailer towing related definitions will assist you in understanding the following information: gross vehicle weight rating (gvwr) the gvwr is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight. The total load ...

  • Page 260

    Tongue weight (tw) the tongue weight is the downward force exerted on the hitch ball by the trailer. In most cases it should not be less than 10% of the trailer load. You must consider this as part of the load on your vehicle. Frontal area the frontal area is the maximum height multiplied by the max...

  • Page 261

    Weight-distributing hitch a weight-distributing system works by applying lever- age through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle’s front axle and the trailer axle(s). When used in accordance with the manufacturer’s direc...

  • Page 262

    Trailer hitch classification the following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer hitch classification definitions clas...

  • Page 263

    Trailer towing weights (maximum trailer weight ratings) engine/ trans- mission versions gvw (gross vehicle weight) wb (wheel base) max. Gawr (gross axle weight rat- ing) gcwr (gross com- bined weight rating) frontal area max. Gtw (gross trailer weight) max. Tongue weight 3.6l/ auto- matic all 8,550 ...

  • Page 264

    Engine/ trans- mission versions gvw (gross vehicle weight) wb (wheel base) max. Gawr (gross axle weight rat- ing) gcwr (gross com- bined weight rating) frontal area max. Gtw (gross trailer weight) max. Tongue weight 3.6l/ auto- matic all 8,900 lbs (4 036 kg) l2 136 in (3 450 mm) front 4,400 lbs (2 0...

  • Page 265

    Engine/ trans- mission versions gvw (gross vehicle weight) wb (wheel base) max. Gawr (gross axle weight rat- ing) gcwr (gross com- bined weight rating) frontal area max. Gtw (gross trailer weight) max. Tongue weight 3.6l/ auto- matic all 9,350 lbs (4 241 kg) l4 159 in (4 035 mm) front 4,350 lbs (1 9...

  • Page 266

    Note: the trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and should never exceed the weight referenced on the tire and loading information placard. Refer to “tire safety information” in “starting and operating” for further information. Trailer and ton...

  • Page 267

    Note: remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to the “tire and loading information” placard for the maximum combine...

  • Page 268

    Warning! Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may ...

  • Page 269

    Warning! (continued) • total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. Gvwr 2. Gtw 3. Gawr 4. Tongue weight rating for the trailer hitch uti- lized. Towing requirements — tires • do not attempt to tow a trailer while ...

  • Page 270

    Towing requirements — trailer brakes • do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • an electronically actuated trailer brake controller is required when towing a trailer w...

  • Page 271

    Caution! (continued) could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing requirements — trailer lights and wiring whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motorin...

  • Page 272

    The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Four-pin connector 1 — female pins 4 — park 2 — male pin 5 — left stop/turn 3 — ground 6 — right stop/turn seven-pin connector 1 — battery 5 — ground...

  • Page 273

    Towing tips before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Automatic transmission the drive gear can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. H...

  • Page 274

    Cooling system to reduce potential for engine and transmission over- heating, take the following actions: city driving when stopped for short periods, shift the transmission into neutral and increase engine idle speed. Highway driving reduce speed. Air conditioning turn off temporarily. Recreational...

  • Page 275

    Recreational towing — automatic transmission recreational towing is allowed only if the front wheels are off the ground. This may be accomplished using a tow dolly or vehicle trailer. If using a tow dolly, follow this procedure: 1. Properly secure the dolly to the tow vehicle, following the dolly ma...

  • Page 277: Contents

    What to do in emergencies contents 䡵 hazard warning flashers . . . . . . . . . . .277 䡵 if your engine overheats . . . . . . . . . . . .277 䡵 wheel and tire torque specifications . . . . . . . . . . . . . . . . . . . . . .278 ▫ torque specifications . . . . . . . . . . . . . . . . . . .278 䡵 tirefit...

  • Page 278

    䡵 freeing a stuck vehicle . . . . . . . . . . . . .308 䡵 shift lever override . . . . . . . . . . . . . . . .309 䡵 towing a disabled vehicle . . . . . . . . . . .310 ▫ automatic transmission . . . . . . . . . . . . . . . .311 276 what to do in emergencies.

  • Page 279

    Hazard warning flashers the hazard warning flasher switch is located on the instrument panel below the climate controls. Press the switch to turn on the hazard warning flasher. When the switch is activated, all direc- tional turn signals will flash on and off to warn oncoming traffic of an emergency...

  • Page 280

    Caution! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads hot (h), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on hot (h), and you hear conti...

  • Page 281

    Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against the wheel. Wheel mounting surface torque patterns 6 what to do in emergencies 279.

  • Page 282

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Tirefit kit — if equipped small punctures up to ¼” (6 mm) in the tire tread can be sealed with tirefit. ...

  • Page 283

    Using the mode select knob and hoses your tirefit kit is equipped with the following symbols to indicate the air or sealant mode. Selecting air mode push in the mode select knob (5) and turn to this position for air pump operation only. Use the black air pump hose (7) when selecting this mode. Selec...

  • Page 284

    • the sealant bottle (1) and sealant hose (6) are a one tire application use and need to be replaced after each use. Always replace these components immediately at your original equipment vehicle dealer. • when the tirefit sealant is in a liquid form, clean water, and a damp cloth will remove the ma...

  • Page 285

    Warning! • do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the tirefit kit. • do not use tirefit or drive the vehicle under the following circumstances: – if the puncture in the tire tread is approx...

  • Page 286

    Warning! (continued) • tirefit sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep tirefit out of reach of children. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water. Do not induce vomiting! Consult a phy...

  • Page 287

    4. Remove the cap from the valve stem and then screw the fitting at the end of the sealant hose (6) onto the valve stem. 5. Uncoil the power plug (8) and insert the plug into the vehicle’s 12 volt power outlet. Note: do not remove foreign objects (e.G., screws or nails) from the tire. (c) injecting ...

  • Page 288

    Note: if the mode select knob (5) is on air mode and the pump is operating, air will dispense from the air pump hose (7) only, not the sealant hose (6). If the sealant (white fluid) does flow through the sealant hose (6): 1. Continue to operate the pump until sealant is no longer flowing through hos...

  • Page 289

    3. Immediately disconnect the sealant hose (6) from the valve stem, reinstall the cap on the fitting at the end of the hose, and place the tirefit kit in the vehicle storage location. Quickly proceed to (d) “drive ve- hicle.” caution! • the metal end fitting from power plug (8) may get hot after use...

  • Page 290

    (e) after driving: pull over to a safe location. Refer to “whenever you stop to use tirefit” before continuing. 1. Push in the mode select knob (5) and turn to the air mode position. 2. Uncoil the power plug and insert the plug into the vehicle’s 12 volt power outlet. 3. Uncoil the air pump hose (7)...

  • Page 291

    5. Replace the sealant bottle (1) and sealant hose (6) assembly at your authorized dealer as soon as pos- sible. Refer to (f) “sealant bottle and hose replace- ment”. Note: when having the tire serviced, advise the autho- rized dealer or service center that the tire has been sealed using the tirefit...

  • Page 292

    Jacking and tire changing warning! • do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • being under a jacked-up vehicle is dangerous. The vehicle could slip...

  • Page 293

    Removing the spare tire 1. Remove the spare tire before attempting to jack up the vehicle. Attach the lug bolt adapter to the winch extension and insert it into the winch mechanism. Jack location jack tools 1 — winch extension 2 — lug bolt adapter 3 — wrench handle 6 what to do in emergencies 291.

  • Page 294

    2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle. Winch location winch extension 292 what to do in emergencies.

  • Page 295

    Note: the winch mechanism is designed for use with the winch extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. Lowering spare tire spare tire 6 what ...

  • Page 296

    4. Remove the retainer nut prior to removing the retainer from the wheel. 5. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable. Retainer nut lifting spare tire 294 what to do in emergencies.

  • Page 297

    6. Pull the retainer through the center of the wheel. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. Warning! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit whe...

  • Page 298

    5. Turn the ignition off. 6. Block the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. Note: passengers should not remain in the vehicle when the vehicle is being jacked. Jacking instructions warning! ...

  • Page 299

    Warning! (continued) • do not let anyone sit in the vehicle when it is on a jack. • do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • only use the jack in the positions indicated and for lifti...

  • Page 300

    1. Loosen (but do not remove) the wheel lug bolts by turning them to the left one turn while the wheel is still on the ground. 2. There are two jack engagement locations on each side of the vehicle body. Caution! Do not attempt to raise the vehicle by jacking on locations other than those indicated....

  • Page 301

    Note: the rear jacking location is located in front of the rear tire and in front of the leaf spring mount. Note: the front jacking location is located behind the front tire and in front of the driver’s door. Warning! Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack ...

  • Page 302

    Warning! (continued) under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. 3. Place the wrench on the jack screw and turn to the right until the jack head is properly engaged in the described location. Do not raise...

  • Page 303

    Warning! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in personal injury. Note: do not install the wheel cover on the compact spare. 7. Lower the vehicle by turning the jack sc...

  • Page 304

    11. Stow the jack, jack handle and winch handle tools back in the storage compartment. 12. Check the compact spare tire pressure as soon as possible. Correct the tire pressure, as required. Wheel covers caution! Use a back-and-forth motion to remove the hub cap. Do not use a twisting motion when rem...

  • Page 305

    Warning! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations for jump-start the vehicle’s jump starting remote posts are located under the hood, in the engine compartment on the driver’s side. The remote positive (+) post is cove...

  • Page 306

    Warning! • take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You co...

  • Page 307

    Caution! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Connecting the jumper cables 1. Connect the positive (+) end of the jumper cable to the remote positive (+) post of the discharged vehicle. Note: the remote pos...

  • Page 308

    6. Once the engine is started, disconnect the jumper cables in the reverse sequence: disconnecting the jumper cables 1. Disconnect the negative end (-) of the jumper cable from the remote negative (-) post of the vehicle with the discharged battery. 2. Disconnect the opposite end of the negative (-)...

  • Page 309

    Battery location there are two remote jump starting posts under the hood which is the recommended jump start location. If access to the battery is needed, an access panel on the driver’s side floor will allow for battery access. Access panel battery location 6 what to do in emergencies 307.

  • Page 310

    Freeing a stuck vehicle if your vehicle becomes stuck in mud, sand, or snow, it can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the front wheels. Then shift back and forth between drive and reverse , while gently pressing the accelerator. Us...

  • Page 311

    Warning! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehi- cle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously w...

  • Page 312

    Towing a disabled vehicle this section describes procedures for towing a disabled vehicle using a commercial wrecker service. Towing condition wheels off the ground all models flat tow none if transmission is operable: • transmission in neutral • 25 mph (40 km/h) max speed • 15 miles (24 km) max dis...

  • Page 313

    Caution! Do not use sling type equipment when towing. When securing the vehicle to a flat bed truck, do not attach to front or rear suspension components. Dam- age to your vehicle may result from improper towing. Automatic transmission the manufacturer recommends towing your vehicle with all four wh...

  • Page 315: Maintaining Your Vehicle

    Maintaining your vehicle contents 䡵 engine compartment — 3.6l . . . . . . . . . .315 䡵 onboard diagnostic system — obd ii . .316 ▫ loose fuel filler cap message . . . . . . . . . . . .316 䡵 emissions inspection and maintenance programs . . . . . . . . . . . . . . . . . . . . . . . . . .317 䡵 replace...

  • Page 316

    ▫ appearance care and protection from corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . .342 ▫ cleaning the instrument panel cupholders . .347 䡵 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .348 ▫ underhood fuses. . . . . . . . . . . . . . . . . . . . . .349 ▫ interior...

  • Page 317

    Engine compartment — 3.6l 1 — washer solvent reservoir 5 — power distribution center (fuses) 2 — engine oil fill 6 — coolant reservoir 3 — engine oil dipstick 7 — power steering reservoir 4 — brake fluid reservoir 7 maintaining your vehicle 315.

  • Page 318

    Onboard diagnostic system — obd ii your vehicle is equipped with a sophisticated onboard diagnostic system called obd ii. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide ex...

  • Page 319

    “electronic vehicle information center (evic)” in ”un- derstanding your instrument panel” for further informa- tion. Tighten the gas cap until a ⬙ clicking ⬙ sound is heard. This is an indication that the gas cap is properly tight- ened. Press the odometer reset button to turn the message off. If th...

  • Page 320

    Your vehicle has a simple ignition key-actuated test, which you can use prior to going to the test station. To check if your vehicle’s obd ii system is ready, you must do the following: 1. Cycle the ignition switch to the on position, but do not crank or start the engine. Note: if you crank or start...

  • Page 321

    Before going to the i/m station. The i/m station can fail your vehicle because the mil is on with the engine running. Replacement parts use of genuine mopar® parts for normal/scheduled maintenance and repairs is highly recommended to en- sure the designed performance. Damage or failures caused by th...

  • Page 322

    Besides those maintenance items specified in the fixed “maintenance schedule”, there are other components which may require servicing or replacement in the future. Caution! • failure to properly maintain your vehicle or per- form repairs and service when necessary could result in more costly repairs...

  • Page 323

    Regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the min and...

  • Page 324

    American petroleum institute (api) engine oil identification symbol this symbol means that the oil has been certified by the american petroleum institute (api). The manufacturer only recommends api certified engine oils. Caution! Do not use chemical flushes in your engine oil as the chemicals can da...

  • Page 325

    Synthetic engine oils you may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed. Materials added to engine oil the manufacturer strongly recommends against the ad- dition of any a...

  • Page 326

    Warning! The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner, hoses, etc.) unless such removal is necessary for repair or maintenance. Make sure that no one is near the engine comp...

  • Page 327

    Warning! • exhaust gases can injure or kill. They contain carbon monoxide (co), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing co, refer to “safety tips/exhaust gas” in “things to know before starting your vehicle” for further...

  • Page 328

    Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. Note: intentional tampering with emissions control systems can result in c...

  • Page 329

    Warning! • battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water. R...

  • Page 330

    Air conditioner maintenance for best possible performance, your air conditioner should be checked and serviced by an authorized dealer at the start of each warm season. This service should include cleaning of the condenser fins and a performance test. Drive belt tension should also be checked at thi...

  • Page 331

    Refrigerant recovery and recycling r-134a air conditioning refrigerant is a hydrofluoro- carbon (hfc) that is endorsed by the environmental protection agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by authorized dealer or othe...

  • Page 332

    Caution! The a/c air filter is identified with an arrow to indicate airflow direction through the filter. Failure to properly install the filter will result in the need to replace it more often. 7. Rotate the glove compartment door back into position. Body lubrication locks and all body pivot points...

  • Page 333

    Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Note: life expectancy of wiper blades varies depend- ing on geographical area and frequency of use. Poor performance of blades may ...

  • Page 334

    Cooling system warning! • when working near the radiator cooling fan, disconnect the fan motor lead or turn the ignition switch to the off position. The fan is temperature controlled and can start at anytime the ignition switch is in the on position. • you or others can be badly burned by hot engine...

  • Page 335

    Refer to the “maintenance schedule” for the proper maintenance intervals. Note: some vehicles require special tools to add coolant properly. Failure to fill these systems properly could lead to severe internal engine damage. If any coolant is needed to be added to the system please contact your loca...

  • Page 336

    Caution! (continued) • do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • this vehicle has not been designed for use with...

  • Page 337

    • use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system. Please note that it is the owner’s responsibility to main- tain ...

  • Page 338

    Warning! • do not open hot engine cooling system. Never add engine coolant (antifreeze) when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pressure cap w...

  • Page 339

    Points to remember note: when the vehicle is stopped after a few miles/ kilometers of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high humidity accumulating on the radiator and being vapor- ized when th...

  • Page 340

    Brake system in order to assure brake system performance, all brake system components should be inspected periodically. Refer to the “maintenance schedule” for the proper maintenance intervals. Warning! Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot rest...

  • Page 341

    Use only manufacturer’s recommended brake fluid. Re- fer to “fluids, lubricants, and genuine parts” in “main- taining your vehicle” for further information. Warning! • use only manufacturer’s recommended brake fluid. Refer to “fluids, lubricants, and genuine parts” in “maintaining your vehicle” for ...

  • Page 342

    Warning! (continued) • do not allow petroleum based fluid to contaminate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in a collision. Automatic transmission selection of lubricant it is important to use the proper transmission ...

  • Page 343

    Leaks. Avoid using transmission sealers as they may adversely affect seals. Caution! Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the new vehicle limited warranty. Fluid level check the fluid level is prese...

  • Page 344

    Appearance care and protection from corrosion protection of body and paint from corrosion vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons a...

  • Page 345

    • if insects, tar, or other similar deposits have accumu- lated on your vehicle, use mopar® super kleen bug and tar remover to remove. • use a high quality cleaner wax, such as mopar® cleaner wax to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • av...

  • Page 346

    • if you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • if a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. • use mopar® touch up paint on scratches as soon as possible. You...

  • Page 347

    • blot any remaining stain with a clean, damp towel. • for tough stains, apply mopar® total clean, or a mild soap solution to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. • for grease stains, apply mopar® multi-purpose cleaner to a clean, damp cloth and remov...

  • Page 348

    Liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition. Warning! Do not use volatile solvents for cleaning purposes. Many ar...

  • Page 349

    When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning plastic instrument cluster lenses the lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be...

  • Page 350

    Cleaning the liner is top shelf dishwasher safe, or you may follow the cleaning procedure below. Soak the liner in a mixture of medium hot tap water and one teaspoon of mild liquid dish soap. Let soak for approximately 30 minutes. After 30 minutes, pull the liner from the water and dip it back into ...

  • Page 351

    Warning! (continued) • if a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Underhood fuses the front power distribution center is located on the driver’s side of t...

  • Page 352

    Cavity maxi fuse mini fuse description f01 40 amp orange esc pump f02 20 amp yellow (3.6 gasoline engine) starter relay 3.6l (3.6 gasoline en- gine) f02 50 amp red (3.0 diesel engine) glow plug unit (3.0 diesel engine) f04 50 amp red (3.6 gasoline engine) secondary pdc (trans power relay, vacuum pum...

  • Page 353

    Cavity maxi fuse mini fuse description f07 50 amp red (non a/c) 60 amp blue (a/c) engine cooling fan - 1st speed f08 40 amp orange passenger com- partment blower f09 15 amp blue rear power outlet f10 15 amp blue horn f11 15 amp blue mprop-drv (3.0 diesel engine) — if equipped cavity maxi fuse mini f...

  • Page 354

    Cavity maxi fuse mini fuse description f17 20 amp yellow secondary loads, ecm (3.0 diesel engine) f18 7.5 amp brown kl30 ecm, kl30 main relay coil (3.6 gasoline engine) f18 7.5 amp brown kl30 mta, kl30 ecm, kl30 main relay coil (3.0 die- sel engine) f19 7.5 amp brown a/c compressor (if equipped) f20...

  • Page 355

    Front pdc additional fuses the additional fuse box is located inside the front pdc box. Cavity mini fuse description f61 20 amp yellow vacuum pump (3.6 gaso- line engine) — if equipped f62 30 amp green transmission power rele (3.6 gasoline en- gine) — if equipped f64 7.5 amp brown urea pump (3.0 die...

  • Page 356

    Cavity mini fuse description f12 10 amp red right low beam f13 10 amp red left low beam f31 5 amp beige int/a f32 10 amp red sbmt f34 7.5 amp brown clearance lights f36 15 amp blue +30 (acm – tpcu – rrm – dlc) f37 5 amp beige int (brake no – ipc) f38 15 amp blue central locking cavity mini fuse desc...

  • Page 357

    Cavity mini fuse description f90 7.5 amp brown left high beam f91 7.5 amp brown right high beam f92 7.5 amp brown left fog lamp f93 7.5 amp brown right fog lamp right central pillar fuses the right central pillar fuse panel is located on the interior side at the base of the passenger side b pillar. ...

  • Page 358

    Cavity mini fuse description f84 20 amp yellow rear right windows heater f85 10 amp red rear heater prep vehicle storage if you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • disconnect the negative cable from the battery. • anytim...

  • Page 359

    Bulb number daytime running lamps (if equipped) 7440 front side marker lamps wy5w rear tail/stop lamps 7443 rear turn signal lamps 7440na rear backup lamps 921 rear side marker lamps w3w front fog lamps h11 license plate lamps c5w front roof lamps wy5w rear roof lamps w3w note: • numbers refer to co...

  • Page 360

    Front turn signal/parking lamps 1. Rotate the bulb counter clockwise and remove. 2. Install the bulb into socket, and rotate bulb/socket clockwise into lamp locking it in place. Daytime running lamp (drl)/front side marker lamp 1. Remove the plastic cap from the back of the headlamp housing. 2. Remo...

  • Page 361

    Front, rear roof lamps 1. Remove two screw and remove the lamp assembly. 2. Remove the socket bulb by turning counterclockwise. 3. Remove bulb and replace as needed. 4. Reinstall the bulb socket and rotate clockwise to lock in place. 5. Reinstall lamp. Rear tail, stop, backup, turn signal and rear s...

  • Page 362

    Fluid capacities u.S. Metric fuel (approximate) 24 gallons 90 liters engine oil with filter 3.6l engine (sae 5w-20, api certi- fied) 6 quarts 5.6 liters cooling system * 3.6l engine (mopar® antifreeze/ engine coolant 10 year/150,000 mile formula or equivalent) 10.5 quarts 10 liters 360 maintaining y...

  • Page 363

    Fluids, lubricants and genuine parts engine component fluid, lubricant, or genuine part engine coolant we recommend you use mopar® antifreeze/coolant 10 year/150,000 mile formula oat (organic additive technology) meeting the requirements of chrysler material standard ms-12106. Engine oil we recommen...

  • Page 364

    Chassis component fluid, lubricant, or genuine part automatic transmission – 3.6 gasoline engine only use only atf+4® automatic transmission fluid. Fail- ure to use atf+4® fluid may affect the function or performance of your transmission. We recommend mopar® atf+4® fluid. Brake master cylinder we re...

  • Page 365: Maintenance Schedules

    Maintenance schedules contents 䡵 maintenance schedule . . . . . . . . . . . . .364 ▫ maintenance chart . . . . . . . . . . . . . . . . . . . .366 8 m a i n t e n a n c e s c h e d u l e s.

  • Page 366

    Maintenance schedule your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate in th...

  • Page 367

    • check the tire inflation pressures and look for unusual wear or damage • check the fluid levels of the coolant reservoir, brake master cylinder, and power steering and fill as needed • check function of all interior and exterior lights required maintenance intervals refer to the maintenance schedu...

  • Page 368

    Maintenance chart refer to the maintenance schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 ...

  • Page 369

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 370

    Mileage or time passed (whichever comes first) 20,000 30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 1 10,000 120,000 130,000 140,000 150,000 or years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 or kilometers: 32,000 48,000 64,000 80,000 96,000 1 12,000 128,000 144,000 160,000 176,000 192,000 208,0...

  • Page 371

    Warning! • you can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic. • failure to properly inspect and m...

  • Page 373: Contents

    If you need consumer assistance contents 䡵 suggestions for obtaining service for your vehicle . . . . . . . . . . . . . . . . . . . . . . .373 ▫ prepare for the appointment. . . . . . . . . . . . .373 ▫ prepare a list . . . . . . . . . . . . . . . . . . . . . . . .373 ▫ be reasonable with requests ....

  • Page 374

    䡵 department of transportation uniform tire quality grades . . . . . . . . . . . . . . . . .379 ▫ treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .379 ▫ traction grades . . . . . . . . . . . . . . . . . . . . . . .379 ▫ temperature grades. . . . . . . . . . . . . . . . . . . .380 372 if...

  • Page 375

    Suggestions for obtaining service for your vehicle prepare for the appointment if you are having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty. Discuss additional charges with the service manager....

  • Page 376

    Facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be re- solved with this process. • if for some reason...

  • Page 377

    In mexico contact: av. Prolongacion paseo de la reforma, 1240 sante fe c.P. 05109 mexico, d. F. In mexico city: 5081-7568 outside mexico city: 1-800-505-1300 customer assistance for the hearing or speech impaired (tdd/tty) to assist customers who have hearing difficulties, the manufacturer has insta...

  • Page 378

    The manufacturer will not stand behind any service contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the manufacturer’s service contract. If you purchased a ser- vice contract that is not a manufacturer’s service contract, and you req...

  • Page 379

    Mopar® parts mopar® fluids, lubricants, parts, and accessories are available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle operating at its best. Reporting safety defects in the 50 united states and washington, d.C. If you believe that your vehi...

  • Page 380

    Publication order forms to order the following manuals, you may use either the website or the phone numbers listed below. Visa, mas- tercard, american express, and discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. Note: a street address is required wh...

  • Page 381

    Call toll free at: • 1–800–890–4038 (u.S.) • 1–800–387–1143 (canada) or visit us on the worldwide web at: • www.Techauthority.Com department of transportation uniform tire quality grades the following tire grading categories were established by the national highway traffic safety administration. The...

  • Page 382

    Warning! The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature grades the temperature grades are a (the highest), b, and c, representing the tire’s resistan...

  • Page 383: Index

    Index 10

  • Page 384

    Adding engine coolant (antifreeze) . . . . . . . . . . . .334 adding fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251 adding washer fluid . . . . . . . . . . . . . . . . . . . . . .331 additives, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .249 airbag. . . . . . . . . ....

  • Page 385

    Special additives . . . . . . . . . . . . . . . . . . . . . . .340 torque converter . . . . . . . . . . . . . . . . . . . . . . .198 battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .326 keyless transmitter replacement (rke) . . . . . . . .20 belts, seat . . . . . . . . . . . ...

  • Page 386

    Cigar lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 clean air gasoline . . . . . . . . . . . . . . . . . . . . . . . .247 cold weather operation . . . . . . . . . . . . . . . . . . . .185 compact disc (cd) maintenance . . . . . . . . . . . . . .174 compact spare tire . . . . . ....

  • Page 387

    Door locks, automatic . . . . . . . . . . . . . . . . . . . . . .23 driving through flowing, rising, or shallow standing water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 electric remote mirrors. . . . . . . . . . . . . . . . . . . . . .71 electronic brake control system . . ....

  • Page 388

    Exhaust gas caution. . . . . . . . . . . . . . . . . . . . . . . .63 exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . .63 exterior lighting . . . . . . . . . . . . . . . . . . . . . . . . . .87 exterior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 fabric care. ....

  • Page 389

    Requirements . . . . . . . . . . . . . . . . . . . . . . . . . .247 tank capacity . . . . . . . . . . . . . . . . . . . . . . . . . .360 fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251 fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .348 gas cap (fu...

  • Page 390

    Heater, engine block . . . . . . . . . . . . . . . . . . . . . . .186 high beam/low beam select (dimmer) switch . . . . .89 hill start assist. . . . . . . . . . . . . . . . . . . . . . . . . . .213 hitches trailer towing . . . . . . . . . . . . . . . . . . . . . . . . .260 hood release . . . . . . ....

  • Page 391

    Anti-lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132 brake assist warning . . . . . . . . . . . . . . . . . . . .211 brake warning . . . . . . . . . . . . . . . . . . . . . . . . .124 bulb replacement . . . . . . . . . . . . . . . . . . . . . . .357 check engine (malfunction indica...

  • Page 392

    Lubrication, body . . . . . . . . . . . . . . . . . . . . . . . . .330 lug nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .278 maintenance free battery. . . . . . . . . . . . . . . . . . . .326 maintenance, general . . . . . . . . . . . . . . . . . . . . . .121 maintenance procedur...

  • Page 393

    Filter disposal . . . . . . . . . . . . . . . . . . . . . . . . .323 identification logo . . . . . . . . . . . . . . . . . . . . . .322 materials added to . . . . . . . . . . . . . . . . . . . . . .323 recommendation . . . . . . . . . . . . . . . . . . . . . . .321 synthetic . . . . . . . . . . . . ...

  • Page 394

    Reminder, seat belt. . . . . . . . . . . . . . . . . . . . . . . . .37 remote sound system (radio) controls . . . . . . . . .173 replacement bulbs . . . . . . . . . . . . . . . . . . . . . . . .356 replacement keys . . . . . . . . . . . . . . . . . . . . . . . . .16 replacement parts. . . . . . . . ...

  • Page 395

    Service manuals . . . . . . . . . . . . . . . . . . . . . . . . . .378 service reminder indicator . . . . . . . . . . . . . . . . . .121 shift lever override . . . . . . . . . . . . . . . . . . . . . . .309 shoulder belts . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 shoulder belt upper ...

  • Page 396

    General information . . . . . . . . . . . . . . . . . . . . .227 high speed . . . . . . . . . . . . . . . . . . . . . . . . . . .230 inflation pressures . . . . . . . . . . . . . . . . . . . . . . .228 life of tires . . . . . . . . . . . . . . . . . . . . . . . . . . .236 load capacity . . . . . . ....

  • Page 397

    Transaxle automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 automatic . . . . . . . . . . . . . . . . . . . . . . . . . . . .186 fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 transm...

  • Page 398

    Windshield wipers . . . . . . . . . . . . . . . . . . . . . . . . .92 wiper blade replacement . . . . . . . . . . . . . . . . . . .330 wipers, intermittent . . . . . . . . . . . . . . . . . . . . . . . .92 wrench (service indicator) . . . . . . . . . . . . . . . . . . .121 396 index.

  • Page 399

    Installation of radio transmitting equipment special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be obser...

  • Page 400

    P r o m a s t e r chrysler group llc o w n e r ’ s m a n u a l 2 0 1 4 2014 promaster 14vf-126-ac third edition printed in u.S.A..