- DL manuals
- Ramblewood Green
- Cooktop
- GC1-28N
- User Manual
Ramblewood Green GC1-28N User Manual
Summary of GC1-28N
Page 1
User guide gas cooktop model: gc2-48n gc2-48p gc1-28n gc1-28p gc2-43p gc2-43n gc2-43pb (battery ignition) 1.
Page 2
Your safety and the safety of others are very importatnt. Before use, please read and follow all safety rules and operating instructions. And save for local gas and electrical inspector’s use. Warning: if the information in this manual is not followed exactly, a fire or explosion may result causing ...
Page 3: Save These Instructions
This cooktop is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded receptacle. Do not cut of remove the grounding prong from this plug. Disconnect the electrical supply before servicing the cooktop. Injuries may...
Page 4: Installation
Installation installation and service must be conducted by qualified / licensed technician, in accordance with national & local regulation. Failure to comply will void the product warranty. always disconnect the appliance power before installation & maintenance. these cooktops are designed to be...
Page 5
Installation in kitchen cabinet with door (fig.2) it is recommended that a 30 mm clearance be left between the cooker top and the fixture surface (fig.2). Note: the adjacent furniture and all materials used in installation must be able to withstand a minimum of 85°c above the ambient temperature. Ho...
Page 6
Kitchen furniture are particularly prone to heat damage or discoloration at temperatures below 85°c. Discharging products of combustion extractor hoods connected directly to the outside should be provided, to allow the products of combustion of the cooktop to be discharged (fig.3), (fig.4). 6.
Page 7
Settling the hob for installation every cooktop is provided with a set of tabs for fitting to the unit with thickness from 3 to 4 cm, and a seal with adhesive on one side. remove burners and grids. turn the cooktop over and rest the top side on a cloth. apply the self-adhesive seal “g” as illu...
Page 8
Connect the cooktop to gas shut off the main gas supply valve before disconnecting the old cooktop and leave it off until the new hook-up has been completed. Don’t forget to relight the pilot on other gas appliances when you turn the gas back on. Never use an old connector when installing a new cook...
Page 9
Adapting the cooktop for different types of gas to adapt the cooktop to a different type of gas than th at for which it was designed, (see the sticker under the hob or on the package), the burner nozzles must be changed, as follows: remove the pan supports and slide the burners out of the cooktop. U...
Page 10
Turn the knob to minimum level the adjustment screw is located in the center of the shaft (fig.9). Please remove/pull out the control knob to access it. Using a screwdriver with max. Diameter 3 mm, turn the screw inside the tap until the correct setting is obtained. C) leakage test to prevent gas le...
Page 11
Piping. When using test pressure of 1/2 psig or less to test the gas supply system, simply isolate the cooktop from the gas supply system by closing the individual shut-off valve. Electrical connection (certain models) 120volt, 60 hertz, properly grounded dedicated circuit protected by a 15-amp or 2...
Page 12
Do not, under any circumstances, cut or remove the third (ground) prong from this poer cord. Temporary method (adapter plugs not permitted canada) caution: attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal, not insu...
Page 13
13.
Page 14: How To Use The Cooktop
How to use the cooktop gas burners gas flow to the burners is adjusted by turning the knobs which control the valves. Turning the knob so that the indicator line points to the symbols printed on the panel achieves the following functions: when knob is rotated to the maximum position it will permit t...
Page 15
Diameters of the burners. Avoid having flames extending out from underneath the pans (refer to the table). A smaller diameter pot or pan placed on a larger burner does not necessarily mean that the boiling conditions are reach quicker. Table of recommended pans burner Ø pan diameter in cm auxiliary ...
Page 16: Cleaning and Maintenance
Cleaning and maintenance cleaning important: before any operation of cleaning and maintenance disconnect the appliance from the electrical supply. It’s advisable to clean when the appliance is cold and especially for cleaning the enameled parts. avoid leaving alkaline or acidic substances (lemon...
Page 17
Triple ring burner the triple ring burner must be correctly positioned (seen fig.7); the burner rib must be entering in their ligament as shown by the arrow. The burner correctly positioned must not be able to rotate (fig.8). then position the cap a and the ring b (fig.8). 17.
Page 18
Problem debug it may occur that the cooktop does not function or does not function properly. Before calling customer service for assistance, let’s see what can be done. First of all, check to see that there are no interruptions in the gas and electrical supplies, and, in particular, that the gas val...
Page 19
Instruction for gas regulator 1. Product features: this product is a low-pressure pipeline regulator valve, built-in regulator for gas products this regulator is set to natural gas (ng) use. If user wants to set to liquefied petroleum gas (lpg) use, it needs to be set manually, detail see below inst...
Page 20
(figure 2). Take out the adopter pin & flip it, such that the spring faces outward (figure 3). Screw the adopter pin back into top cover assembly. Then put the top cover back onto the regulator (figure 4). Please insure to screw the top cover back on very tight to make good seal. Apply sealant when ...