This tool for use by licensed operators only. Read and obey all safety and operating instructions before operating tool. Cobra tool operator’s safety & operating instruction manual semi-automatic, low velocity piston type fastening tool danger.
Danger safety introduction danger safety introduction 2 danger this tool is to be used only by properly trained and licensed operators. You must successfully complete itw ramset/red head’s training program for the tool and obtain a certified operator’s license before handling, loading or operating t...
Safety instructions danger danger safety instructions 3 preparation acceptable base materials powder actuated fastening is suit- able for use in the following base materials only: • poured concrete • structural steel • masonry joints ( see page 8) never attempt to fasten into any other type of mater...
Safety instructions danger danger safety instructions 4 loads & load selection safety 1. Always make a test fastening after being sure that the base material is suitable for powder actuated fastening. Failure to determine the correct power level to be used may result in the use of excessive power, a...
Danger danger safety instructions 5 safety instructions tool handling safety 1. Always be sure tool is operating properly before attempting to use it. Follow the “daily function check” shown to the right and described on page 9. 2. Always load tool using a load strip selected directly from a box ind...
Danger safety instructions danger safety instructions failure to follow instructions can cause injury to the tool oper- ator or to bystanders. Fastener driving safety 1. Only use the tool for fastening into a suitable base material. 2. Never fire the tool without a fastener. Firing a tool without a ...
Fasteners / loads fasteners / loads 7 your ramset cobra tool uses only the ramset fasteners and loads shown below or listed for the tool in the product catalog. Danger .300 head plastic fluted drive pins .300 head plastic fluted drive pins with 7/8" washer 1/4"-20 threaded studs .300 head top-hat dr...
Fastening applications fastening applications 8 fastening applications your ramset tool can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool, fasteners, and powder ...
Tool operating instructions tool operating instructions 9 tool operation daily function test always check the tool first to make sure that it does not contain a load strip or fastener. Test the tool several times by depressing the muzzle bushing fully on a hard surface and pulling the trigger. You s...
Tool operating instructions tool operating instructions 10 4. Hold the tool perpendicular (90°) to the work surface with both hands and press firmly to fully depress the tool. Maintain firm downward pressure on the tool with both hands and pull the trigger to drive the fastener. Do not depress the t...
Troubleshooting troubleshooting 11 refer to parts schematic for proper assembly of parts - overdriving of fasteners - excessive power - change to next lower power level load strip color and number. - soft base material - check base material (see page 3) - tool fails to fire - failure to depress - se...
Parts schematic parts schematic 12 15 13 12 10 12 16 * 11 14 18 17 19.
Parts listing / maintenance parts listing / maintenance 13 cobra tool parts list key part no. Description 1 sc301500 spall guard 2 sc301009 front barrel (baseplate ) 3 sc301011a shear clip (pkg. Of 3) 4 sc301010 fastener guide 5 sc301200a piston assembly 6 sc301208 piston ring 7 sc302012 pawl ( stop...
Disassembly disassembly 14 tool disassembly 1. Rotate the barrel retention clip off of the pawl using a flat blade screwdriver or the point of a long fastener. 2. Remove the pawl by lifting it up and away from the tool body. 3. Slide the front barrel assembly out of the tool body. 4. Unseat and remo...
Disassembly disassembly 15 6. Slide the piston out of the rear barrel assembly and slide the guide out of the front barrel. The tool is now disassembled for normal cleaning. Inspect all parts for wear or damage and clean or replace as required. Use detergent oil and cleaning brushes to remove dirt a...
Warranty all warranties of the products described herein, expressed or implied, including the warranty of merchantability and fitness for particular pur- poses, are specifically excluded, except for the following: ramset will repair or replace, at its sole option, any tool, part, or fastener which, ...
