1. DL manuals
  2. RAMSET
  3. Gate Opener
  4. RAM-1000 UL
  5. Instruction Manual

RAMSET RAM-1000 UL Instruction Manual

Other manuals for RAM-1000 UL: Instruction Manual

Summary of RAM-1000 UL

  • Page 1

    © ™ no. 545327 us ® c instruction manual model ram-1000 ul & ram-5500 ul for class i, ii, iii, iv vehicular gate operators rev 060202.

  • Page 2

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 1 - table of contents important safety requirements & instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2 mechanical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 3

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 2 - installation should be done by a qualified installer only. Prior to installation, the following must be observed: (per ul 325 51.8.4) a) install the vehicular gate operator only when: 1) the vehicular gate operator is appro...

  • Page 4

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 3 - mechanical specifications: ram-5500 ul foot pedal release foot pedal release ram-1000 ul model: ram-1000 ul ram-5500 ul power input: 120vac 120vac continuous duty motor: 1/2 hp, 120vac, 4.5 a, 1,625 rpm with high speed bear...

  • Page 5

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 4 - these sliding gate operators are factory preset for left hand installations. Pad construction: dimensions given for pad are based on soil bearing shear of 2000 p.S.F. These fig- ures may have to be adjusted depending on loc...

  • Page 6

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 5 - run start 14 ga 12 ga 10 ga 8 ga 120v single phase 1/2 4.7 5.0 up to 50' 50-100' 100-200' 200-300' 120v single phase 3/4 5.8 6.5 up to 50' 50-100' 100-200' 200-300' amperes maximum conduit distance in feet using copper wire...

  • Page 7

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 6 - gate travel adjustment to adjust gate travel, depress spring loaded bracket and spin each adjustment nut to the required position (figure 6). Led must turn on to indicate position open or close when limit switch is activate...

  • Page 8

    Electrical connection a 3 wire, 120vac electrical circuit with a 15 amp independent circuit breaker is required for each oper- ator. Ideally, the electrical conduits should exit the concrete under the operator. Low voltage control wires must be run in a separate conduit to the operator as shown. Int...

  • Page 9

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 8 - intelligate pcb motor controller specifications introduction ramset’s “intelligate” control board is for operating a vehicular gate operator. The control board is available for either 110vac or 220vac, single phase, applica...

  • Page 10

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 9 - dip switch b5: “lag delay” lag on close one second lag on close dip switch b6: “lag mode” lag on open one second lag on open dip switch b7: “reverse logic” dip function ‘off’ left hand operation – standard installation ‘on’...

  • Page 11

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 10 - power must be turned off before servicing operator. Power must be turned off before attempting to adjust the limit switches. Power must be turned off for power failure release. N caution electronic control board must be se...

  • Page 12

    R a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 11 - n warning a non-contact sensor (photoelectric sensor or equivalent) and a contact sensor (edge device or equivalent) is required on each individual installa- tion to comply with ul325. Reversing sensors on the ground floor...

  • Page 13

    Item part # part description ram-1000 ul ram-5500 ul 1 50-031 1/2 hp 115 vac electric motor 1 2 50-039 20 pin edge connector 1 1 3 50-058 3 1/2" uhmw idler pulley 2 2 4 50-069 limit switch 00-h3 2 2 5 50-087 # 41 x 20' gate chain 1 1 6 50-089 3/8" x 2" x 6" chain bracket 2 2 7 50-090 1/2" x 4" chain...

  • Page 14

    4 20 32 49 50 25 46 18 60 2 58 45 62 26 52 51 21 61 20 11 8 47 22 6 7 19 43 44 16 5 58 36 42 13 48 1 33 34 41 3 12 14 57 17 56 59 35 15 23 53 54 55 38 24 63 ram-1000 ul parts diagram r a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 13 - figure 13.

  • Page 15

    Ram-5500 ul parts diagram figure 14 4 20 32 31 39 25 37 18 60 2 58 27 62 26 52 51 21 61 20 11 8 29 22 6 7 19 43 44 16 5 58 36 42 13 28 40 33 34 41 3 12 14 57 17 56 59 35 15 23 53 54 55 38 24 63 r a m s e t z r a m s e t z r a m s e t ra ms et z ra ms et z ra ms et - 14 -.

  • Page 16

    V i s i t v i s i t o u r w e b s i t e o u r w e b s i t e a a t t : w w w : w w w . R a m s e t i n c . C o m . R a m s e t i n c . C o m ramset automatic gate systems z (800) 771-7055 z 9116 de garmo ave. Z sun valley, ca. 91352 glossary classes of vehicular gate operators vehicular horizontal sl...