- DL manuals
- RAMSET
- Tools
- T3MAG
- Instruction Manual
RAMSET T3MAG Instruction Manual
Summary of T3MAG
Page 1
Ramset t3 tool systems t3ss single shot & t3 magazine operator’s safety & operating instruction manual danger read and obey all safety and operating instructions before operating tool. Gas powered, low velocity piston type fastening tool t3ss single shot t3 magazine t3ss t3mag.
Page 2: Safety Introduction
Safety introduction danger safety introduction danger 2 ! Read, understand and follow the instructions in the tool manual before attempting to use the tool. ! Operators and bystanders must wear eye and hearing protection. ! Never close tool with hand over the fastener loading end of the tool. A seri...
Page 3: Preparation For Fastening
Preparation for fastening acceptable base materials the gas powered t3 tools are suitable for use in the following base materials only: • poured concrete • structural steel • concrete block and horizontal joints in brick or masonry walls never attempt to fasten into any other type of material. Faste...
Page 4: Fastening Applications
Fastening applications fastening applications 4 fastening applications your t3 tools can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool and fasteners, as well as ...
Page 5: Failure To Follow
Failure to follow instructions can cause injury to the tool operator or to bystanders. • use the tool only in well ventilated areas. • always hold the tool at right angles to the work surface. • never attempt to make a fastening at an angle to the work surface. • while the tool can be used in any po...
Page 6
Battery cell and charger the first step in preparing a new tool for operation is to fully charge the new battery. New batteries are shipped discharged and must be charged for 24 hours before first use. All subsequent charges will require at most a 3 hour charge. Warning important charging notes chem...
Page 7: Installing The Battery
Installing the battery • insert the battery into the tool as shown on the right with the clip facing to the side. • the battery has two positions in the tool: 1. The “off” position—as shown in picture #1 to the right. 2. The “run” position—as shown in picture #2 to the right. • to operate the tool b...
Page 8: Fuel Cell
Fuel cell fuel cell 8 fuel cell danger explosion/fire hazard read all safety instructions before using or handling the fuel cell. Failure to follow all instructions may result in explosion or fire. This may cause severe personal injuries or property damage. Keep the fuel cell away from heat, sparks ...
Page 9: Installing The
Installing the fuel cell • the t3 fuel cell comes ready to use. There is no need for additional steps to prepare the fuel cell. The fuel cell also incorporates a usage indicator, to indicate a new fuel cell from a used fuel cell. • there is a membrane over the top of the fuel cell adaptor. If the fu...
Page 10
T3ss tool operating instructions t3ss tool operating instructions 10 tool operation always check the tool first to make sure that it does not contain a fastener. If the tool contains a fastener from a previous application, remove both the battery and the fuel cell before attempting to remove the fas...
Page 11: Quick Change Nose
Quick change nose the t3ss tool is equipped with a quick change nose. This feature allows the user to change the work contact element to meet various fastening needs. The work contact element can be changed without the use of tools by following these steps: removal 1. Remove battery from the tool !!...
Page 12
Tool operation always check the tool first to make sure that it does not contain a fastener. If the tool contains a fastener from a previous application, remove both the battery and the fuel cell before attempting to remove the fastener. Operating the t3 tool 1. Insert a charged battery into the too...
Page 13: Parts Schematic
Parts schematic 13 parts schematic t3 tool system schematic – motor assembly.
Page 14: Parts List
Parts list 14 parts list ramset t3 tool systems parts list – motor assembly key part number description 1 b0017 grill, cap 2 b0095 foam filter 3 901065a cap screws ( pkg of 4) 4 b0016 cap assembly 5 b0121 spark plug wire 6 b0061a pc board screws (pkg of 3) 7 b0040 pc board 8 7505164 spark plug assem...
Page 15
T3 tool systems – handle assembly t3 tool systems – handle assembly 15 ramset t3 tool systems parts list – handle assembly key part number description 1 333380 knob assembly 2 404619 insulator (2) not shown 3 404490 trigger switch 4 7405091 screws, #2 x 5/8”, trigger switch 5 b0134 spark unit – mefi...
Page 16
T3ss nose and housing assembly 16 t3ss nose and housing assembly ramset t3ss nose and housing assembly key part number description 1 b0001 housing 2 b0096 shroud 3 b0052t3ss nose/sleeve assembly t3ss 4 b0217a cage assembly, t3ss/t3ssmag 5 b0175 shear block plate kit, t3ss (use with tools before s/n ...
Page 17: T3 Magazine Nose Assembly
T3 magazine nose assembly t3 magazine nose assembly 17 ramset t3 magazine nose assembly key part number description 1 b0001 housing 2 b0199 shroud 3 b0052a nose / sleeve assembly, t3mag 4 b0217a cage assembly with screws, t3mag 5 b0110a shear block kit, t3mag shear block, t-nuts (2), screws (2) 7 b0...
Page 18
T3 magazine – magazine assembly 18 t3 magazine – magazine assembly ramset t3 magazine – magazine assembly key part number description 1 b0203 magazine left & right half 2 b0204 front & rear rails 3 b0205 connection block & screws 4 b0206 connection block screws only 5 b0207 follower assembly w/const...
Page 19
Servicing / troubleshooting servicing / troubleshooting 19 symptom possible problems service preparing tool for operation—battery/charger problems — battery cell does not — inoperative indicator — try battery cell in tool after 3 hours appear to accept lights on charger on charge cycle. If tool led ...
Page 20
Symptom possible problems service power/exhaust stage of operation — tool operates properly, — battery cell is — charge battery cell but fasteners do not discharged drive fully — fuel cell is low — check fuel cell according to operating manual and replace as required. — there may be loss of — press ...
Page 21: Warranty
Ramset warrants that new t3ss and t3 magazine systems power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below. Two-year/50,000 shot warranty a two-year/50,000 shot warranty, which ever comes first, will apply to all parts, except ...
Page 22
For tool repair service contact your local authorized ramset distributor or to find your nearest ramset tool repair center visit our web site at www.Ramset.Com or call 800-241-5640 concrete fastening systems glendale heights, il 60139 800-ramset6 (1-800-726-7386) www.Ramset.Com buy with confidence.....