- DL manuals
- RAMSET
- Tools
- T3MAG
- Instruction manual
RAMSET T3MAG Instruction manual
Summary of T3MAG
Page 1
Ramset tf1200 tool system operator’s safety & operating instruction manual danger read and obey all safety and operating instructions before operating tool. Gas powered, low velocity piston type fastening tool.
Page 2: Safety Introduction
Safety introduction danger safety introduction danger 2 ! Read, understand and follow the instructions in the tool manual before attempting to use the tool. ! Operators and bystanders must wear eye and hearing protection. ! Never close tool with hand over the fastener loading end of the tool. A seri...
Page 3: Preparation For Fastening
Preparation for fastening acceptable base materials the gas powered tf1200 tools is suitable for use in the following base materials only: • poured concrete • structural steel • concrete block and horizontal joints in brick or masonry walls never attempt to fasten into any other type of material. Fa...
Page 4: Fastening Applications
Fastening applications fastening applications 4 fastening applications your tf1200 tools can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool and fasteners, as well...
Page 5: Failure to Follow
Failure to follow instructions can cause injury to the tool operator or to bystanders. • use the tool only in well ventilated areas. • always hold the tool at right angles to the work surface. • never attempt to make a fastening at an angle to the work surface. • while the tool can be used in any po...
Page 6
Battery cell and charger the first step in preparing a new tool for operation is to fully charge the new battery. New batteries are shipped discharged and must be charged for 24 hours before first use. All subsequent charges will require at most a 3 hour charge. Warning important charging notes chem...
Page 7: Installing The Battery
Installing the battery • insert the battery into the tool as shown on the right with the clip facing out. • the battery has two positions in the tool: 1. The “off” position—as shown in picture #1 to the right. 2. The “run” position—as shown in picture #2 to the right. • to operate the tool be sure t...
Page 8: Fuel Cell and Metering Valve
Fuel cell and metering valve fuel cell and metering valve 8 fuel cell danger explosion/fire hazard read all safety instructions before using or handling the fuel cell. Failure to follow all instructions may result in explosion or fire. This may cause severe personal injuries or property damage. Keep...
Page 9: Fuel Cell and Metering Valve
Fuel cell and metering valve 9 fuel cell and metering valve inserting fuel cell with the metering valve stem pointed toward the front of the tool, insert the metering valve/fuel cell assembly. As you slide the metering valve/fuel cell assembly into the tf1200 tool, you will notice that there is a re...
Page 10
Tool operation always check the tool first to make sure that it does not contain a fastener. If the tool contains a fastener from a previous application, remove both the battery and the fuel cell before attempting to remove the fastener. Operating the tf1200 tool 1. Insert a charged battery into the...
Page 11: Servicing / Troubleshooting
Servicing / troubleshooting servicing / troubleshooting 11 symptom possible problems service preparing tool for operation—battery/charger problems — battery cell does not — inoperative indicator — try battery cell in tool after 3 hours appear to accept lights on charger on charge cycle. If tool led ...
Page 12: Servicing / Troubleshooting
Symptom possible problems service power/exhaust stage of operation — tool operates — battery cell is — charge battery cell properly, but fasteners discharged do not drive fully — fuel cell is low — check fuel cell according to operating manual and replace as required. — there may be loss of — press ...
Page 13: Warranty
Ramset warrants that new tf1200 magazine systems power fastening tools, parts and accessories will be free from defects in material and workmanship for the period shown below. Two-year/50,000 shot warranty a two-year/50,000 shot warranty, which ever comes first, will apply to all parts, except those...
Page 14
For tool repair service contact your local authorized ramset distributor or to find your nearest ramset tool repair center visit our web site at www.Ramset.Com or call 800-241-5640 concrete fastening systems glendale heights, il 60139 800-ramset6 (1-800-726-7386) www.Ramset.Com buy with confidence.....