Viper tool operator’s safety & operating instruction manual danger this tool for use by licensed operators only. Read and obey all safety and operating instructions before operating tool. Semi-automatic, low velocity piston type fastening tool herramienta viper manual de instrucciones de funcionamie...
Just as no one can merely read a book about driving an automobile and then hope to drive one safely, no one should attempt to use any ramset tool without adequate, competent personal instruction. And just as one must be licensed to drive an automobile, one must also be licensed to use a powder actua...
Preparation acceptable base materials powder actuated fastening is suitable for use in the following base materials only: • pouredconcrete • structuralsteel • masonryjoints(seepage8) never attempt to fasten into any other type of material. Fastening into other materials can cause blindness or other ...
Loads & load selection safety 1. Always make a test fastening after being sure that the base material is suitable for powder actuated fastening. Failure to determine the correct power level to be used may result in the use of excessive power, allowing the fastener to pass completely through the work...
Tool handling safety 1. Always be sure tool is operating properly before attempting to use it. Follow the “daily function test” shown to the right and described on page 9. 2. Always load tool using a strip load selected directly from a box indicating the power load type and number. Never attempt to ...
Failure to follow instructions can cause injury to the tool operator or to bystanders. Fastener driving safety 1. Only use the tool for fastening into a suitable base material. 2. Never fire the tool without a fastener. Firing a tool without a fastener will cause the piston to strike the work surfac...
Your ramset viper tool uses only the ramset fasteners and loads shown below or listed for the tool in the product catalog. Fasteners and fastener assemblies ceiling clip assemblies - .300 head dia. Cat. No. Shank dia. Length sdc100 .145 1” sdc125 .145 1-1/4” spc78* .150powerpoint 7/8” spc114* .150/....
Fastening applications your ramset tool can be used for a wide range of fastening needs in a variety of base materials. Reading and follow these important fastening guidelines will help you get the best results from your tool, fasteners, and powder loads, as well as help you perform these fastening ...
Tool operation daily function test always check the tool first to make sure that it does not contain a load strip or fastener. Test the tool overhead several times by completely depressing it on a hard surface. You should hear an audible click as the firing pin releases. Let up on the tool and check...
4. Lower the tool, keeping it pointed in a safe direction, and insert the next fastener or fastener assembly. Note: while the viper tool is being closed and fired, the advance lever cam has caused the load advance lever to be indexed downward to pick up the next load. When the tool is lowered and op...
Refer to parts schematic for proper assembly of parts – overdriving of fasteners – excessive power – change to the next lower power level load color and number. – soft base material – check base material (see page 3) – tool fails to fire – failure to depress – see “tool does not completely completel...
Parts schematic parts schematic 12 diagrama de piezas diagrama de piezas 12.
Parts list / maintenance parts list / maintenance 13 always make sure the tool is not loaded before performing any service or repair and always wear safety goggles when cleaning or servicing the tool. Daily cleaning all front end parts shown in the disassembly section are to be cleaned daily with a ...
Disassembly 14 disassembly tool disassembly 1. Unscrew and remove the barrel retention collar. Handle the tool carefully after the collar is unscrewed to prevent the two barrel pawls from falling out. 2. Remove the two pawls from the slots on either side of the tool housing. 3. Slide the barrel asse...
Disassembly 15 disassembly 6. Remove the buffer from the muzzle bushing. Inspect all parts for wear or damage and clean or replace as required. Use cleaning solvent and cleaning brushes to remove dirt and powder residues. Wipe all parts dry before reassembly. Wear safety goggles when cleaning tool p...
Viper warranty and limitations powder actuated tool manufactures' institute inc. Tm concrete fastening systems glendale heights, il 60139 800-ramset6(1-800-726-7386) www.Ramset.Com buy with confidence... Buy from your authorized distributor an illinois tool works company © illinois tool works 2009 p...
