- DL manuals
- RAMSET
- Tools
- Viper Tool
- Operator's Safety & Operating Instruction Manual
RAMSET Viper Tool Operator's Safety & Operating Instruction Manual
Summary of Viper Tool
Page 1
This tool for use by licensed operators only. Read and obey all safety and operating instructions before operating tool. Viper tool operator’s safety & operating instruction manual semi-automatic, low velocity piston type fastening tool danger.
Page 2: Danger
Danger safety introduction danger safety introduction 2 danger this tool is to be used only by properly trained and licensed operators. You must successfully complete itw ramset/red head’s training program for the tool and obtain a certified operator’s license before handling, loading or operating t...
Page 3: Safety Instructions
Safety instructions danger danger safety instructions 3 preparation acceptable base materials powder actuated fastening is suit- able for use in the following base materials only: • poured concrete • structural steel • masonry joints ( see page 8) never attempt to fasten into any other type of mater...
Page 4: Safety Instructions
Safety instructions danger danger safety instructions 4 loads & load selection safety 1. Always make a test fastening after being sure that the base material is suitable for powder actuated fastening. Failure to determine the correct power level to be used may result in the use of excessive power, a...
Page 5: Danger
Danger danger safety instructions 5 safety instructions tool handling safety 1. Always be sure tool is operating properly before attempting to use it. Follow the “daily function check” shown to the right and described on page 9. 2. Always load tool using a load strip selected directly from a box ind...
Page 6: Danger
Danger safety instructions danger safety instructions failure to follow instructions can cause injury to the tool oper- ator or to bystanders. Fastener driving safety 1. Only use the tool for fastening into a suitable base material. 2. Never fire the tool without a fastener. Firing a tool without a ...
Page 7: Fasteners / Loads
Fasteners / loads fasteners / loads 7 your ramset viper tool uses only the ramset fasteners and loads shown below or listed for the tool in the product catalog. Danger ceiling clip assemblies - .300 head dia. The power level of the loads is indicated by the number marked on each box, the color of th...
Page 8: Fastening Applications
Fastening applications fastening applications 8 fastening applications your ramset tool can be used for a wide range of fastening needs in a variety of base materials. Reading and following these important fastening guidelines will help you get the best results from your tool, fasteners, and powder ...
Page 9: Tool Operating Instructions
Tool operating instructions tool operating instructions 9 tool operation daily function test always check the tool first to make sure that it does not contain a load strip or fastener. Test the tool overhead several times by completely depressing it on a hard surface. You should hear an audible clic...
Page 10: Tool Operating Instructions
Tool operating instructions tool operating instructions 10 4. Lower the tool, keeping it pointed in a safe direction, and insert the next fastener or fastener assembly. Note: while the viper tool is being closed and fired, the advance lever cam has caused the load advance lever to be indexed downwar...
Page 11: Troubleshooting
Troubleshooting troubleshooting 11 refer to parts schematic for proper assembly of parts - overdriving of fasteners - excessive power - change to next lower power level load strip color and number. - soft base material - check base material (see page 3) - tool fails to fire - failure to depress - se...
Page 12: Parts Schematic
Parts schematic parts schematic 12.
Page 13: Parts Listing / Maintenance
Parts listing / maintenance parts listing / maintenance 13 viper tool parts list key part no. Description 1 mvp100a muzzle bushing assembly 2 mvp140 piston 3 mvp150 barrel 4 mvp21a springs (barrel, firing pin & firing pin assembly) 5 mvp110a buffer (package of 3) 6 tool housing (not a spare part) 7 ...
Page 14: Disassembly
Disassembly disassembly 14 tool disassembly 1. Unscrew and remove the barrel retention collar. Handle the tool carefully after the collar is unscrewed to prevent the two barrel pawls from falling out. 2. Remove the two pawls from the slots on either side of the tool housing. 3. Slide the barrel asse...
Page 15: Disassembly
Disassembly disassembly 15 6. Remove the buffer from the muzzle bushing. Inspect all parts for wear or damage and clean or replace as required. Use detergent oil and cleaning brushes to remove dirt and powder residues. Wipe all parts dry before reassembly. Wear safety goggles when cleaning tool part...
Page 16: Warranty
Warranty all warranties of the products described herein, expressed or implied, including the warranty of merchantability and fitness for particular pur- poses, are specifically excluded, except for the following: ramset will repair or replace, at its sole option, any tool, part, or fastener which, ...