- DL manuals
- Rangemaster
- Hob
- RMB60HPNGFGL
- User Manual
Rangemaster RMB60HPNGFGL User Manual
Summary of RMB60HPNGFGL
Page 1
Rmb60hpngfgl/ gas on glass hob user guide & installation & service instructions u110606 - 01.
Page 3: Contents
Contents 1. Before you start... 1 2. Hob overview 3 3. Cleaning your hob 5 4. Troubleshooting 7 5. Installation 8 6. Conversion to lpg 14 7. Circuit diagram 20 8. Technical data 21 11. Warranty/after sales service 23.
Page 5: Installation and Maintenance
1 thank you for buying a rangemaster hob. It should give you many years trouble-free cooking if installed and operated correctly. It is important that you read this section before you start, particularly if you have not used a gas hob before. Caution: this appliance is for cooking purposes only. It ...
Page 6: Cleaning
2 do not use water on grease fires and never pick up a flaming pan. Turn off the controls and then smother a flaming pan on a surface unit by covering the pan completely with a well fitting lid or baking tray. If available, use a multi-purpose dry chemical or foam- type fire extinguisher. Take care ...
Page 7: 2. Hob Overview
3 artno.311-0001 right pans gas artno.316-0025 rgg77 hob control to high artno.316-0026 rgg77 hob control to low the diagram by each of the control knobs indicates which burner that knob operates (fig. 2.1) . Each burner has a special flame safety device (fsd) that stops the flow of gas if the flame...
Page 8: Hob Care
4 pans and kettles with concave bases or down turned base rims should not be used (fig. 2.5) . Simmering aids, such as asbestos or mesh mats, are not recommended. They will reduce burner performance and could damage the pan supports (fig. 2.6) . You should also avoid using unstable and misshapen pan...
Page 9: Essential Information
5 artno.316-0007 gas burner a b d c f e fig.3-1 a – cap, b – head, c – notch, d – base, e – fsd, f – electrode essential information allow the cooker to cool and then isolate the electricity supply before carrying out any thorough cleaning. Never use paint solvents, washing soda, caustic cleaners, b...
Page 10: Cleaning Table
6 cleaning table refer to the cleaning tables ( table 3-1 and table 3-2 ) for details on cleaning the hob. The cleaners listed are available from supermarkets or electrical retailers. For enamelled surfaces use a cleaner that is approved fro use on vitreous enamel. Artno.050-0009 cleaning table 1 ho...
Page 11: 4. Troubleshooting
7 if there is an installation problem and i don’t get my original installer to come back to fix it, who pays? You do. Service organisations will charge for their call- outs if they are correcting work carried out by your original installer. Therefore, it’s in your own interest to keep track of this ...
Page 12: Dear Installer
8 installation check the appliance is electrically safe and gas sound when you have finished. Dear installer before you start your installation, please complete the details below. This hob is a class 3 appliance. Should your customer have a problem relating to your installation they will be able to ...
Page 13: Checking The Parts
9 installation check the appliance is electrically safe and gas sound when you have finished. You will need the following equipment to complete the hob installation satisfactorily: • gas pressure tester • flexible gas hose • multimeter you will also need the following tools: • electric drill • jigsa...
Page 14: Positioning The Hob
10 installation check the appliance is electrically safe and gas sound when you have finished. Positioning the hob the hob should be fitted into a work surface, which is at least 600mm deep. In position, the hob has a maximum thickness of 80mm from the top of the work surface, and an overall thickne...
Page 15: Installing The Hob
11 installation check the appliance is electrically safe and gas sound when you have finished. Fixing the seal to the back of the hob the hob must be sealed to the work surface to prevent liquid from entering into the cabinet. A tape seal is supplied with the hob. 1. Turn the hob over and place in o...
Page 16
12 installation check the appliance is electrically safe and gas sound when you have finished. Front side seal a seal c gas connection seal b seal c overlaps seals b seal c overlaps seals b step 6 seal a step 2: inner seal step 3 step 4: outer seal step 5 seal c seal b seal c overlaps overlaps seal ...
Page 17: Installing The Hob
13 installation check the appliance is electrically safe and gas sound when you have finished. 20 mm min. 40 mm max. 20 mm min. 40 mm max. Front side rear side r f front screw rear screw knobs f front side (f) rear side (r) rear screw rear screw front screw front screw r r f fig. 5.5 fig. 5.6 fasten...
Page 18: Injectors
Warning – servicing to be carried out only by an authorised person disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. 14 check in the ‘ technical data ’ section at the back of the instructions that the cooker is convertible to the gas you want to us...
Page 19: Tap Adjustment
Warning – servicing to be carried out only by an authorised person disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. 15 a fig. 6.3 tap adjustment disconnect from the electricity supply. When changing from one type of gas to another, the minimum tap...
Page 20: Conversion to Lp
16 installation check the appliance is electrically safe and gas sound when you have finished. Conversion to lp if the appliance is to be converted to lp gas do the conversion at this point. See the conversion section of these instructions. Gas connection before connecting the appliance, check that ...
Page 21: Connection to The Gas Supply
17 installation check the appliance is electrically safe and gas sound when you have finished. 1/2" g conical (iso 7-1) male 1/2" g cylindrical (iso 228-1) male b a c 1/2" g cylindrical (iso 228-1) female fig. 6.1 fig. 6.2 connection to the gas supply gas connection (gb) cat: ii 2h3+ the fitting (fi...
Page 22: Safety Information
18 installation check the appliance is electrically safe and gas sound when you have finished. Safety information ensure that the gas supply pipe is never able to touch moveable parts of the built-in cabinet (e.G. Drawers). It must not pass through compartments that could be used for storage purpose...
Page 23: Electrical Connections
19 installation check the appliance is electrically safe and gas sound when you have finished. Electrical connections this appliance must be installed by a qualified electrician to comply with the relevant institute of electrical engineers (i.E.T.) regulations and also the local electricity supply c...
Page 24: 7. Circuit Diagram
20 7. Circuit diagram brown blue yellow & green yellow & green blue blue red micro switch spark 4 spark 3 spark 2 spark 1 igniter.
Page 25: 8. Technical Data
21 8. Technical data the hob is an independent class 3 built-in unit. This hob is category ii 2h3 + it is supplied set for group h natural gas. A conversion kit from ng to lp is available for the hob. Installer: please leave these instructions with the user. Data badge location: base of the hob. Cou...
Page 26: Hotplate Efficiency
22 hotplate efficiency brand rangemaster model identification rmb60hpngfgl/ size (mm) 600 type gas type of hob gas number of gas burners 4 auxiliary / small burner (ee gas burner) - semi-rapide / medium burner (ee gas burner) 55.63 % rapide / large burner (ee gas burner) 53.68 % hotplate ee gas hob ...
Page 27
23 if consultation or technical assistance is needed, please provide the local authorised service agent with the purchase invoice and the product code/serial number. The 2 years free maintenance for the operation of the appliance started from the date of purchase of this product. Any cosmetic damage...
Page 28
24 notes.
Page 29
25 notes.
Page 30
26 notes.
Page 31
27 notes.
Page 32
Clarence street, royal leamington spa, warwickshire, cv31 2ad, england. Tel: +44 (0) 800 8046261 e-mail: consumers@agarangemaster.Co.Uk.