Rangemaster RMHDT110SS User's Manual & Installation Instructions - • Installation

Other manuals for RMHDT110SS: Instruction Manual
Manual is about: Rangemaster Cooker Hood User Guide & Installation Instructions

Summary of RMHDT110SS

  • Page 1

    Rmhdt90ss/ users guide & installation instructions rmhdt110ss/.

  • Page 2: Contents

    Contents important safety information installation page 2 child safety 2 maintenance and service 3 your appliance operating instructions cooker hood controls 4 to operate 5 recirculation 5 extraction 5 maintenance and cleaning metal grease filters 6 charcoal filter 6 lighting 7 cleaning 7 installati...

  • Page 3: • Installation

    These warnings are provided in the interests of safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about the meaning of any of these warnings contact the helpline. • installation • any installation work mus...

  • Page 4

    Important safety information • maintenance and service • this appliance can be a hazard if the grease filters and charcoal filters are not cleaned and replaced as recommended. • always insist on genuine rangemaster spare parts. • the halogen light and cover lamp might hot. • under no circumstances s...

  • Page 5: Operating Instructions

    Operating instructions the chimney hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air. Cooker hood controls the chimney hood functions are controlled by four push buttons located central...

  • Page 6: To Operate

    To operate select the required fan speed and light if required. To obtain the best performance when cooking it is advisable to switch the chimney hood on for a few minutes before you start cooking and leave it running for about 15 minutes after finishing. Recirculation in the recirculation mode cont...

  • Page 7: Metal Grease Filters

    Regular maintenance and cleaning will ensure good performance and reliability, while extending the working life of the hood. Special attention should be paid to the grease filter cassettes and the charcoal filter when the hood is used in the recirculation mode. Before carrying out any mainte- nance ...

  • Page 8: Lighting

    Lighting the canopy is fitted with two 20w halogen spotlamps. Warning! The halogen light and cover lamp might hot. If one of the spotlamps fails to function check that the two pins are correctly inserted into the lamp holder. To replace a spotlamp remove the snap-on lamp cover by levering it from un...

  • Page 9: Technical Information

    It is dangerous to alter the specifications or attempt to modify this chimney hood in any way. Technical information dimensions canopy: height 48mm width 1098-898mm depth 5 20mm chimney: height - upper chimney 215mm lower chimney 740mm width 300mm depth 260mm electrical supply voltage: ~50hz 230v po...

  • Page 10: Electrical Requirements

    Electrical requirements any permanent electrical installation must comply with the latest i.E.E. Regulations and local electricity board regulations. For your own safety this should be undertaken by a qualified electrician e.G. Your local electricity board, or a contractor who is on the roll of the ...

  • Page 11: Components

    Components the chimney hood comprises of the following: - no 1 150x120mm ducting spigot (a) no 1 125x120mm ducting spigot (d) no 1 canopy (c) no 2 recirculation grilles (g) no 1 lower chimney stack (i) no 1 recirculation ducting (p) no 2 recirculation extension ducts (p1) no 1 recirculation spigot (...

  • Page 12: Installing The Chimney Hood

    Installing the chimney hood clearance heights the chimney hood is designed to be fitted over a cooking appliance. A minimum clear- ance height of 650mm (25½ins) is required when installed above a built-in electric hob, or 700mm (27½ins) when installed above a built-in gas hob. When installed between...

  • Page 13: Installing The Chimney Hood

    Installing the chimney hood 4. Drill the holes for the fixing screws using an 8mm masonry drill bit. Insert the rawl plugs and fix the brackets (2) using the 4.2 x 44.4mm screws provided. Drilling the holes 1 1. Draw a horizontal line through the vertical 970mm up the wall from the top of the cookin...

  • Page 14: Installing The Chimney Hood

    Installing the chimney hood ducting the hood is more effective when used in the extraction mode (ducted to the outside). When used in the extraction mode ensure the ducting spigot has been correctly fitted as illustrated. The ducting used must be ∅ ∅ ∅ ∅ ∅ 125 (5ins) or ∅ ∅ ∅ ∅ ∅ 150mm (6ins), flexi...

  • Page 15: Installing The Chimney Hood

    Installing the chimney hood by pressing it downwards until the two pieces meet. 3. Connect the two recirculation extension ducting pipes p1 on to the outlets on either side of the spigot r, which push fit into position,by pressing them horzontally until the two pieces meet. 4. Do not fit the recircu...

  • Page 16

    436001900_05 - 0710011 73/23/cee dir. 89/336/cee 93/68/cee the symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ...