Rapid 7500 136 Installation, operation & service manual - Warning
7500-S
ERIES
I
NSTALLATION
, O
PERATION
AND
S
ERVICE
M
ANUAL
20 of 143
SECTION 6: LIFTING AN AIR TURNOVER UNIT
The air t
u
rno
v
er
u
nit m
u
st
b
e installed in compliance
w
ith all applica
b
le codes. The q
u
alified installer or
ser
v
ice technician m
u
st
u
se
b
est
bu
ilding practices
w
hen installing the air t
u
rno
v
er
u
nit and any optional
eq
u
ipment. Before installation, check local
distri
bu
tion condition, nat
u
re of f
u
el and f
u
el
press
u
re, and the c
u
rrent state of adj
u
stment of the
appliance are compati
b
le.
6.1 Liftin
g
an Air Turnover Unit
6.1.1 Preparin
g
to Lift the Air Turnover Unit:
Prior to lifting the air t
u
rno
v
er
u
nit, the follo
w
ing steps
m
u
st
b
e performed.
1. Remo
v
e all packaging or
b
lockers.
2.
Remo
v
e all of the accessories or packages that
w
ere shipped on a skid, inside the air t
u
rno
v
er
u
nit or inside the control enclos
u
re.
3.
Inspect the air t
u
rno
v
er
u
nit to:
•
Verify that there is no damage as a res
u
lt of
shipping.
•
Ens
u
re that it is appropriately rated for the
u
tilities a
v
aila
b
le at the installation site.
•
Verify that the lifting l
u
gs are intact,
u
ndamaged and sec
u
red to the air t
u
rno
v
er
u
nit.
•
Ens
u
re factory-installed hard
w
are is
torq
u
ed as specified.
4.
Prepare the installation location to
b
e ready to
accept the air t
u
rno
v
er
u
nit.
5.
Verify that the lifting eq
u
ipment can handle the
air t
u
rno
v
er
u
nit’s
w
eight and the req
u
ired
reach.
6.1.2 Liftin
g
an Air Turnover Unit
Lift the air t
u
rno
v
er
u
nit into place
b
y installing
appropriate hard
w
are (s
u
pplied
b
y others) into all fo
u
r
0.75" (1.9 cm) diameter lifting l
u
gs holes. Use
spreader
b
ars to ens
u
re that the lifting ca
b
les clear
the sides of the air t
u
rno
v
er
u
. Use ca
u
tion as the load may
b
e
u
n
b
alanced. The air t
u
rno
v
er
u
nit m
u
st
b
e kept le
v
el
d
u
ring the lift to pre
v
ent tipping, t
w
isting or falling. If
lifted improperly, prod
u
ct damage may occ
u
r.
Lift each piece separately and then assem
b
le.
for assem
b
ly instr
u
ctions. Refer
to the applica
b
le portions of
for
assem
b
ly and mo
u
nting instr
u
ctions for specific
accessories.
WARNING
Crush Hazard
Use proper lifting equipment and practices.
Failure to follow these instructions can result
in death, injury or property damage.