Rapid Electronics 400S Owner's Manual - page 6
. .
.
.
7
10
OPERATION
SILENT ARMING / DISARMING: Pressing the transmitters and buttons
at the same time will arm or disarm your security system. No chirping
sound will be heard and the arm / disarm confirmation will be visible with
the parking lights only.
SHOCK SENSOR BY-PASS: Pressing the button on the transmitter (2)
times within 3 seconds will arm the security system and by-pass the
shock sensor. The system will chirp one additional time to confirm the
sensor bypass mode was activated. The sensor bypass feature is programmed
to activate for (1) arming cycle only. The security system will return to
normal operation during the next arming cycle.
NOISELESS MODE: Press the button (1) time to arm the system.
Press the button (2) more times within 3 seconds: The siren will chirp
(1) more time. The system is now in Noiseless Mode. In Noiseless
mode the zone 4 shock sensor timer will be reduced from 30 seconds to 15
seconds. The noiseless feature is programmed to activate for (1) arming
cycle only. The security system will return to normal operation during the
next arming cycle.
HIDDEN ALARM FUNCTION: Press the button first then within 3
seconds, press the button to activate the Hidden Alarm Function.
The security system will arm and be in Hidden Alarm Function. The
siren or horn will be silenced even if the sensor is triggered in the armed
status.
G. PASSIVE ARMING (See Alarm Feature II-2 Programming.)
Active Arming / Disarming will allow you to operate your security system
with the remote transmitter only. This security system is equipped with
an optional Passive Arming feature, which allows the security system
to automatically arm 30 seconds after the last door is closed.
To enter Passive Arming:
1. Turn the ignition to the OFF position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for
30 seconds. If you re-open the doors, hood or trunk, the security system
LED will stop flashing. It will begin flashing again once the vehicles
entrances are closed.
OPERATION
5. Turn the ignition switch to the Off position. [4] Chirps from the siren
or horn and [3] flashes from parking lights will indicate the system was
disarmed.
J. VALET MODE: (Disarm or Valet mode)
The valet/program switch allows you to temporarily bypass all alarm
functions, eliminating the need to hand your transmitter to parking
attendants or garage mechanics. When the system is in valet mode, all
alarm functions and remote starter functions are bypassed, however the
remote panic feature and remote door locks will remain operational. To use
the valet mode, the system must first be disarmed either by using you
remote transmitter, or by operating the manual override sequence.
To Enter Valet Mode:
1. Turn ignition to the ON position.
2. Press and hold the valet/program switch for 2 seconds or until the
LED turns on. The LED will remain on and solid for as long as the system
is in Valet Mode.
To Exit Valet Mode:
1. Returning to normal operation, turn ignition switch to the ON position.
2. Press and hold the valet/program switch for 2 seconds. The LED will
turn OFF indicating the system is out of Valet Mode.
Remote Valet: ( Disarm or Valet mode)
Press and release the button on the transmitter three times within 3
seconds to enter or exit valet mode. The parking light flash to confirm
you have entered Valet Mode and [2]parking light flashes will
confirm you have exited Valet Mode.
K. CAR FINDER:
With the unit Armed, press the button to activate the Car Finder function.
The siren will chirp 6 times and the parking lights will flash 12 times to
locate your vehicle.
L. PANIC FUNCTION:
The transmitter can be used as a remote panic button to manually trigger
the alarm in case of emergency.
To enter Panic Mode:
1. Press and hold the button for 3 seconds. The alarm will immediately
sound.