Raritan PX Quick Setup Manual - page 3
3
Raritan PX Quick Setup Guide
QSG-DPX-0O-v1.5.
13-E y 255-80-6081-00 RoHS
2. Secure the baseplates in place. Different models ship with
different types of baseplates.
To secure a baseplate with the thumbscrew, turn the
thumbscrew until it is tightened.
To secure a baseplate WITHOUT the thumbscrew, use
the included L-shaped hex key to loosen the hex
socket screws until the baseplate is fastened.
3. Align the L-brackets with the baseplates so that the five
screw-holes on the baseplates line up through the
L-bracket's slots. The rackmount side of brackets should
face either the left or right side of the PX.
4. Fasten the brackets in place with at least three screws
(one through each slot). Use additional screws as desired.
5. Using rack screws, fasten the PX to the rack through the
L-brackets.
0RXQWLQJ=HUR80RGHOV8VLQJ%XWWRQ0RXQW
1. Align the baseplates on the rear of the PX device. Leave
at least 24 inches between the baseplates for stability.
2. Make the baseplates grasp the PX device lightly. For
details, see step 2 in the procedure:
Mounting Zero U
Models Using L-Brackets
(on page 2).
3. Screw each mounting button in the center of each
baseplate. The recommended torque is 1.96 N·m (20
kgf·cm).
4. Align the large mounting buttons with the mounting holes
in the cabinet, fixing one in place and adjusting the other.
5. Depending on the type of your baseplates, either further
tighten the thumbscrews or loosen the hex socket screws
until the mounting buttons are secured in their position.
6. Ensure that both buttons can engage their mounting holes
simultaneously.
7. Press the PX device forward, pushing the mounting
buttons through the mounting holes, then letting the device
drop about 5/8". This secures the PX in place and
completes the installation.
0RXQWLQJ=HUR80RGHOV8VLQJ&ODZ)RRW%UDFNHWV
1. Align the baseplates on the rear of the PX device.
2. Secure the baseplates in place. For details, see step 2 in
the procedure:
Mounting Zero U Models Using
L-Brackets
(on page 2).
3. Align the claw-foot brackets with the baseplates so that
the five screw-holes on the baseplates line up through the
bracket's slots. The rackmount side of brackets should
face either the left or right side of the PX.
4. Fasten the brackets in place with at least three screws
(one through each slot). Use additional screws as desired.
5. Using rack screws, fasten the PX to the rack through the
claw-foot brackets.
QS Rule
&RQQHFWLQJWKH3;WRD3RZHU6RXUFH
The distance between a PDU and its power source must be
SHORTER than the PDU's line cord to avoid stretching out
the cord. A locking connector used at the power source is
highly recommended for a secure connection.
7RFRQQHFWD3'8WRWKHSRZHUVRXUFH
1. Verify that all circuit breakers on the PX are set to ON. If
not, turn them ON.
Or make sure that all fuses are inserted and seated
properly. If there are any fuse covers, ensure that they
are closed.
Note: Not all PX devices have overcurrent protection
mechanisms.
2. Connect each PX to an appropriately rated branch circuit.
See the label or nameplate affixed to your PX for
appropriate input ratings or range of ratings.
3. With a 1U or 2U model, a blue power LED on the front
panel is lit. A Zero U model does not have a similar power
LED because it will be mounted in the back of a rack.
4. When a PX device powers up, it proceeds with the
power-on self test and software loading for a few
moments. At this time, the outlet LEDs cycle through
different colors.