Ratoc Systems EX30S User Manual - Technical Support
eSATA ExpressCard/34
EX30S
User's Guide
1
2
3
4
5
6
Introduction
* * * 2
-1. Package Contents
* * * 2
-2. Layout
* * * 2
-3. System Requirements
* * * 3
-4. Specifications
* * * 3
-5. Caution
* * * 4
Setup
* * * 5
-1. Installation on Windows System
* * * 5
-2. To Verify Driver Installation (Windows)
* * * 7
-3. Hot-plug tool (Windows)
* * * 8
-4. Installation on Mac system
* * *10
Connecting/Removing eSATA drive
* * *11
-1. Windows
* * *11
-2. Mac
* * *15
Removing ExpressCard
* * *16
-1. How to remove EX30S on Windows
* * *16
-2. How to remove EX30S on Mac
* * *16
Registration & Tech-Support
* * *17
-1. Registration
* * *17
-2. Tech-Support
* * *17
Appendix
* * *18
Contents
-1. Package Contents
Introduction
1
1
-2. Layout
1
eSATA Connector
ExpressCard Connector
Support Port Multiplier)
-3. System Requirements
1
-4. Specification
1
What's Port Multiplier(PM)?
?
..
..
..
.
-5. Caution
1
Setup
2
-1. Installation on Windows system
2
Found New Hardware Wizard
No, not at this time
Next
Install the software automatically(Recommended)
Next
Finish
Windows XP, Server 2003
Silicon Image SiI3132 SATALink Controller
-2. To Verify Driver Installation
2
Silicon Image SiI3132 SATA
Link Controller
What's HotPlug Tool
-3. HotPlug Tool (Windows)
2
14
Add or Remove Programs
Control Panel
HotPlugTool
Change or Remove Programs
OK
Double click HotPlug Tool icon in the task tray to open HotPlug Tool
window.
* To start HotPlug Tool, go to Start
Start - Program
Program - Hot plug tool
Hot plug tool and select
HotPlug Tool.
[1] Removing eSATA drive
[1] Removing eSATA drive
Connected eSATA drives will be listed. Select the drive and click Stop
Stop
button to remove the drive.
[2] Change HotPlug Tool setting
[2] Change HotPlug Tool setting
If the check box is checked, HotPlug Tool runs in the pack ground. If it is
unchecked, HotPlug Tool will not run automatically at the next start.
Note
Drive set as Dynamic disk will not be listed, even if the drive is
connected. Dynamic disk is not supported by hot plugging.
HotPlug Tool Window
HotPlug Tool Window
SCSI Disk
Device
-1. How to use HotPlug Tool (Windows Only)
3
Connecting/Removing eSATA drive
3
If the system recognizes the eSATA drive, the icon of HotPlug Tool will
Finish
Tool
Registration & Tech-support
5
Install HotPlug Tool
Uninstall HotPlug Tool
-4. Installation on Mac System
2
SiI3132_1.1.6u_Sil_Pkg
-2. Connecting/Removing eSATA drive on Mac
3
Removing ExpressCard
4
Safely Remove Hardware
Silicon Image SiI3132 SATALink Controller
-1. How to remove EX30S on Windows
4
-2. How to remove EX30S on Mac
4
Appendix
6
http://www.ratocsystems.com/english/
Software Update and Support
http://www.ratocsystems.com/english/
Technical Support
http://www.ratocsystems.com/english/contact/support.html
[1]
[1]
[2]
[2]
Power off Card
EX3
0S
EX3
0S
EX3
0S
EX3
0S
EX3
0S
EX3
0S
[3]
[3]
[3] Customize
[3] Customize
You can customize HotPlug Tool function.
* Hide icon from Task Tray, if removable disk is not found.
If unchecked, the icon shows all the time.
* Show warning message, if the system disk is removed.
Checked is recommended.
* Enumerate only basic disk as a removable disk.
Checked is recommended.
* Rescan hard disk after resuming from stanby or hibernation mode.
Check, If the hard disk is not recognize after resuming.