- DL manuals
- Raymarine
- Marine Equipment
- A series
- Installation And Operation Instructions Manual
Raymarine A series Installation And Operation Instructions Manual - page 187
Function
Description
Options
Databoxes Set-up
This menu item contains a sub-menu which enables you to turn on and select
information to display in data cells located on the bottom left of the radar
application (Data cells will be displayed in all radar windows).
• Data Cell 1
• Select Data Category
• Data Cell 2
• Select Data Cell
Data Cell 1 & 2
• On
• Off
Select Data Cell
• List of available data by category
Color Palette
This menu item allows you to select a Color Palette for the radar application.
• Bold
• Professional 1
• Professional 2
• Classic
• Night Vision
Range Rings
This menu item allows you to turn the range rings On and Off.
• On
• Off
Safe Zone Ring
This item allows you to show or hid the safe zone ring in the radar application.
• Show
• Hide
Gain Controls
This item allows you to show or hide the onscreen gain controls on
multifunction displays with a touchscreen.
• Show
• Hide
Enhance echoes functions
Enabling radar interference rejection
From the radar application:
1. Select Menu.
2. Select Presentation.
3. Select Enhance Echoes.
4. Select Interference Rejection so that On is highlighted.
Selecting Interference Rejection will switch the function
between On and Off.
5. For non-HD digital radomes you can also select an
interference rejection level:
i.
Select IR Level.
Selecting IR Level will switch between Normal and High.
Enabling radar expansion
From the radar application:
1. Select Menu.
2. Select Presentation.
3. Select Enhance Echoes.
4. Select Expansion so that On is highlighted.
Selecting expansion will switch the function between On and
Off.
5. For non-HD digital radomes you can also select an
interference rejection level
i.
Select Expansion Level.
Selecting Expansion Level will switch between Low and
High.
Radar wakes (Trails)
Radar wakes enable you to see target history. Wakes will appear
differently depending on whether your radar is set to True motion
or Relative motion mode.
Relative motion mode
In relative motion mode radar wakes appear on targets that are
moving relative to the sea (Sea stabilized) this includes targets
that are fixed to the ground, such as piles.
Wakes do not appear if a target is moving at the same speed
and in the same direction as your vessel.
Relative motion mode example
D12744-1
1
2
5
3
4
D
R
A
FT
D
R
A
FT
D
R
A
FT
D
R
A
FT
D
R
A
FT
D
R
A
FT
D
R
A
FT
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
T
E
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
M
P
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
O
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
L
I
LL
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
L
U
S
T
S
T
S
TR
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
R
A
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
I
T
IO
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
O
N
T
E
M
P
O
R
A
R
Y
IL
LU
S
TR
A
TI
O
N
T
E
M
P
O
R
A
R
Y
IL
LU
S
TR
A
TI
O
N
1
Target moving faster and in the same direction as vessel (Wake
appears towards your vessel’s heading).
2
Ships heading marker.
3
Target moving in opposite direction to vessel (Wake appears
opposite to your vessel’s heading).
4
Target moving at approximately the same speed and direction
as vessel (Minimal to no wake).
5
Fixed target (Wake in opposite direction to your vessel’s
heading).
True motion mode
In true motion mode radar wakes appear on targets that are
moving relative to the ground.
Wakes do not appear on targets that are fixed to the ground.
Radar application
187
Summary of A series
Page 1
New a series new c series new e series installation and operation instructions english date: 06-2013 document number: 81337-7 -en © 2013 raymarine uk limited version 7 new a series / new c series / new e series.
Page 3
Trademark and patents notice autohelm, hsb 2 , raytech navigator, sail pilot, seatalk, seatalk ng , seatalk hs and sportpilot are registered trademarks of raymarine uk limited. Raytalk, seahawk, smartpilot, pathfinder and raymarine are registered trademarks of raymarine holdings limited. Flir is a r...
Page 5
Contents chapter 1 important information.......................... 9 tft displays ............................................................... 9 water ingress ............................................................ 10 disclaimers .................................................................
Page 6
7.5 screenshots ...................................................... 102 7.6 resetting your system ........................................ 102 chapter 8 document viewer applica- tion ...................................................................... 103 8.1 document viewer overview .............
Page 7
17.21 transducer set-up menu options ..................... 216 17.22 resetting the sonar ........................................ 218 chapter 18 data application ............................. 219 18.1 data application overview ................................. 220 18.2 selecting datapages using touc...
Page 8
Chapter 30 technical specification.................. 333 30.1 technical specification ...................................... 334 chapter 31 spares and accessories ................ 339 31.1 transducer accessories .................................... 340 31.2 network cables ..............................
Page 9
Chapter 1: important information warning: product installation and operation this product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance. Warning: potential ignition ...
Page 10
Water ingress water ingress disclaimer although the waterproof rating capacity of this product meets the ipx6 standard, water intrusion and subsequent equipment failure may occur if the product is subjected to commercial high-pressure washing. Raymarine will not warrant products subjected to high-pr...
Page 11
Industry canada this device complies with industry canada license-exempt rss standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the...
Page 12
Imo and solas the equipment described within this document is intended for use on leisure marine boats and workboats not covered by international maritime organization (imo) and safety of life at sea (solas) carriage regulations. Technical accuracy to the best of our knowledge, the information in th...
Page 13
Chapter 2: handbook and product information chapter contents • 2.1 handbook information on page 14 • 2.2 product information on page 15 • 2.3 handbook illustrations on page 16 • 2.4 handbook conventions on page 17 • 2.5 touch and non-touch operations on page 19 handbook and product information 13.
Page 14
2.1 handbook information this handbook contains important information regarding your multifunction display. The handbook is for use with the following raymarine multifunction displays: • new a series • new c series • new e series about this handbook this handbook describes how to operate your multif...
Page 15
2.2 product information the following raymarine multifunction display variants are available non- sonar sonar series controls features a65 (e70076) a67 (e70077) new a series touchscreen (hybridtouch when paired with a remote keypad.) • bluetooth. • internal gps. A65 wi-fi (e70162) a67 wi-fi (e70163)...
Page 16
2.3 handbook illustrations the illustrations and screenshots used in this handbook may differ slightly from your display model. The illustration of the multifunction display below is used throughout this manual and unless otherwise stated can apply to all variants of multifunction display (i.E. New ...
Page 17
2.4 handbook conventions the following conventions are used throughout this handbook when referring to: type example convention icons the term "select" is used in procedures involving icons to refer to the action of selecting an on-screen icon, either using touch or physical buttons: • touch — press...
Page 18
Waypoint (mob) button / icon depending on the multifunction display variant there will be either a waypoint (mob) button or an onscreen icon. Wpt button • new c series • new e series • rmk-9 keypad wpt icons • new a series • gs series throughout this manual the term: select wpt, refers to pressing t...
Page 19
2.5 touch and non-touch operations this handbook applies to both touch and non-touch operations. This handbook uses icons to identify whether a particular task is specifically a touch or a non-touch operation. Where a task does not have a touch or non-touch icon then the task can be performed using ...
Page 20
20 new a series / new c series / new e series.
Page 21
Chapter 3: planning the installation chapter contents • 3.1 system integration on page 22 • 3.2 installation checklist on page 27 • 3.3 system limits on page 27 • 3.4 multiple data sources (mds) overview on page 28 • 3.5 identifying your display variant on page 28 • 3.6 networking constraints on pag...
Page 22
3.1 system integration your multifunction display is compatible with a wide range of marine electronics devices. R ay240 1 2 8 5 6 7 3 16 10 9 11 12 13 15 4 18 17 19 20 21 22 23 24 d12244-3 14 0 0 0 0 0 0 a udio 0 0 0 antenna 0 network 0 0 p ower 00 0 0 tack true/app display vmg the display uses a n...
Page 23
Item device type maximum quantity suitable devices connections 4 gps (external) — raymarine 1 any combination of the following: • rs130. • raystar125 gps. • raystar125+ gps (via optional seatalk to seatalk ng converter). Seatalk, seatalk ng , or nmea 0183. 5 instruments — raymarine as determined by ...
Page 24
Item device type maximum quantity suitable devices connections 10 video / camera • new a series = 0 • e7, e7d, new c series = 1 • new e series (excluding e7 and e7d) = 2 composite pal or ntsc video source. Bnc connectors. 10 ip camera multiple note: only 1 ip camera can be viewed at a time. Third pa...
Page 25
Item device type maximum quantity suitable devices connections 17 raymarine sirius marine weather / satellite radio receiver (north america only) 1 seatalk hs : • sr150. • sr100. • sr6. Seatalk ng : • sr50. Seatalk hs , seatalk ng . 18 additional multifunction display(s) — raymarine 5 seatalk hs (re...
Page 26
Item device type maximum quantity suitable devices connections cartography — included embedded (internal) navionics world base map. Internal storage. Cartography — optional external microsd, or microsdhc chart cards: • navionics ready to navigate. • navionics silver • navionics gold • navionics gold...
Page 27
3.2 installation checklist installation includes the following activities: installation task 1 plan your system. 2 obtain all required equipment and tools. 3 site all equipment. 4 route all cables. 5 drill cable and mounting holes. 6 make all connections into equipment. 7 secure all equipment in pla...
Page 28
3.4 multiple data sources (mds) overview installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of gps data. Mds enables you to manage conflicts involving the following types of data: • gps position. • head...
Page 29
3.6 networking constraints new a series, new c series, new e series and gs series displays can be networked together. General • multifunction displays should be connected together using seatalk hs . • multifunction displays can also be connected via seatalk ng or nmea 0183, but not all functions are...
Page 30
3.7 typical systems the illustrations below show examples of possible system configurations, for more details on compatible devices please refer to the system integration section. Note: in the examples below the multifunction display(s) could be any of the following: • new a series • new c series • ...
Page 31
Example: basic system with non-sonar variant display seatalk ng seatalk hs / raynet s martpilot d 12590-1 1 2 3 4 5 1. Multifunction display. 2. Sonar module. 3. Sonar transducer. 4. Spx course computer. 5. Seatalk ng pilot controller. Example: expanded system d12247-2 s eatalk hs / raynet seatalk h...
Page 32
15. Wireless connection. 32 new a series / new c series / new e series.
Page 33
3.8 system protocols your multifunction display can connect to various instruments and displays to share information and so improve the functionality of the system. These connections may be made using a number of different protocols. Fast and accurate data collection and transfer is achieved by usin...
Page 34
3.9 data master any system containing more than one networked multifunction display must have a designated data master. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information. For example the displays may require ...
Page 35
3.11 e7 / e7d parts supplied the parts shown below are supplied with the e7 / e7d multifunction display. D12170-4 x 4 x4 x4 1 2 8 3 4 5 7 9 6 1. Sun cover. 2. Front bezel. 3. Multifunction display. 4. Rear bezel (required for trunnion bracket mounting). 5. Gasket (required for flush mounting). 6. Sc...
Page 36
3.13 tools required for installation d12171-2 1 4 5 3 8 7 6 2 1. Power drill. 2. Jigsaw. 3. Pozidrive screwdriver. 4. Adhesive tape. 5. Spanner for surface mounting or bracket mounting fixings. 6. File. 7. Hole saw for flush mounting (for hole saw size refer to your product’s mounting template). 8. ...
Page 37
Chapter 4: cables and connections chapter contents • 4.1 general cabling guidance on page 38 • 4.2 connections overview on page 39 • 4.3 power connection — new a series on page 40 • 4.4 power connection — new c series and new e series on page 41 • 4.5 network connections on page 43 • 4.6 gps connect...
Page 38
4.1 general cabling guidance cable types and length it is important to use cables of the appropriate type and length • unless otherwise stated use only standard cables of the correct type, supplied by raymarine. • ensure that any non-raymarine cables are of the correct quality and gauge. For example...
Page 39
4.2 connections overview details of the connections available on raymarine multifunction displays are shown below. D12249-6 e 7 e7d e95 / e125 / e1 65 e97 / e127 c95 / c125 c97 / c127 a65 a67 0 0 0 0 0 0 0 0 0 0 power / data transducer seatalk ng seatalk hs / raynet network 1 seatalk hs / raynet net...
Page 40
4.3 power connection — new a series 0 0 0 0 0 1 6 2 4 5 3 d12581-2 1. Multifunction display rear panel connections. 2. Power cable. 3. Connection to 12 v power supply 4. Red cable (positive). 5. Shield (drain) wire (thin black wire; must be connected to rf ground point). 6. Black cable (negative). P...
Page 41
4.4 power connection — new c series and new e series d12250-1 1 2 4 5 7 3 8 6 9 1. Multifunction display connections. 2. Power and data cable. 3. Connection to 12/24 v power supply (e7/e7d is 12v only). 4. Red cable (positive). 5. Fuse. 6. Black cable (negative). 7. Video input cable. 8. Nmea 0183 d...
Page 42
Sharing a breaker where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits. E.G. By connecting an in-line fuse for each power circuit. D11637-2 2 4 4 1 3 + - 1 positive (+) bar 2 negative (-) bar 3 circuit breaker 4 fuse where possible, connect in...
Page 43
4.5 network connections you can connect a number of digital devices to your multifunction display using the network connector(s) at the rear of the unit. A typical network of digital devices may include: • up to 6 raymarine multifunction displays. • seatalk hs or raynet digital devices such as a son...
Page 44
Network cable connector types there are 2 types of network cable connector — seatalk hs and raynet. Seatalk hs connector — used for connecting seatalk hs devices to a raymarine network switch via seatalk hs cables. Raynet connector — used for connecting raymarine network switches and seatalk hs devi...
Page 45
Radar connected directly to the display d12253-2 2 4 3 1 1. Radar scanner 2. Multifunction display rear connector panel. 3. Raynet radar cable. 4. Connection to power supply — open array scanners require a vcm (voltage converter module). Rj45 seatalk hs radar cable connection to connect a radar usin...
Page 46
Digital radar cables you will need a dedicated radar power and data digital cable and appropriate network cables to connect your scanner to your system. Connection required cable radar scanner to power supply and raymarine network switch. Power and data digital cable. For longer cable runs, extensio...
Page 47
1. Rear connector panel of multifunction display (sonar variant). 2. Sonar transducer cable. 3. Sonar transducer. 600 watt sonar-compatible sonar transducer connection via optional adaptor — sonar variant multifunction displays d12257-1 1 2 3 1. Rear connector panel of multifunction display (sonar v...
Page 48
T300 / t400 series thermal camera connection. 2 3 4 5 6 d12260-1 1 8 7 s eatalk hs / raynet seatalk hs / raynet seatalk hs / raynet 1. Multifunction display 2. Raymarine network switch 3. Joystick control unit (jcu), optional 4. Seatalk hs to raynet cable 5. Ethernet cable coupler. 6. Poe (power ove...
Page 49
Item description 3 ip cameras 4 seatalk hs cross over couplers note: multifunction displays do not provide power over ethernet (poe) connected cameras must have their own power supply. Note: if your ip camera(s) are not detected by your multifunction display, try power cycling the ip camera(s) whils...
Page 50
Network connection d12697-3 4 1 2 3 4 1. Network switch. 2. Keypad. 3. Right angled power cable. 4. Networked multifunction displays. When connecting the keypad via a network switch the keypad must be powered separately, using the alternate power connector. Once connected the keypad must be paired w...
Page 51
4.6 gps connection depending on display variant, your multifunction display may include an internal gps receiver. If required the multifunction display can also be connected to an external gps receiver, using seatalk ng or nmea 0183. Gps connection — seatalk ng d12261-1 seatalk ng 1 2 1. Multifuncti...
Page 52
4.8 fastheading connection if you wish to use marpa (radar target acquisition) functions on your multifunction display you need either: • an autopilot connected to the multifunction display via seatalk ng or nmea 0183. The compass is connected to the course computer and calibrated via the pilot cont...
Page 53
Seatalk ng cabling components seatalk ng cabling components and their purposes. Connection / cable notes backbone cable (various lengths) the main cable carrying data. Spurs from the backbone are used to connect seatalk ng devices. T-piece connector used to make junctions in the backbone to which de...
Page 54
4.10 weather receiver operation with multifunction displays if you plan to use a weather receiver with your multifunction display, please follow these guidelines before installing the weather receiver. The standard configuration of multifunction display(s) connected to a weather receiver and additio...
Page 55
Alternative configuration 2: additional multifunction displays 12 v dc 12 v dc* d12566-1 smartpilot nmea 0183 s e at a lk s e at a lk n g s e at a lk n g s e at a lk n g 1 2 1 1 0 1 3 5 4 s e at a lk n g s e at a lk n g s e at a lk h s / r a yn e t s e at a lk h s / r a yn e t s e at a lk n g s e at...
Page 56
4.11 seatalk connection you can connect seatalk devices to your multifunction display using the optional seatalk to seatalk ng converter. D12265-1 seatalk ng s e at a lk 1 2 s e at a lk n g 3 1. Seatalk device. 2. Seatalk to seatalk ng converter. 3. Multifunction display. Seatalk accessories seatalk...
Page 57
4.13 nmea 0183 connection nmea 0183 devices can be connected to new c series and new e series multifunction displays using the power and data cable. Note: new a series does not support connection of nmea 0183 devices. D12266-2 6 1 2 3 4 5 11 7 8 9 10 12 nmea device 4800 / 38400 baud nmea device 4800...
Page 58
4.14 nmea 2000 connection the display can receive data from nmea 2000 devices (e.G. Data from compatible engines). The nmea 2000 connection is made using seatalk ng and appropriate adaptor cables. You can either: • use your seatalk ng backbone and connect each nmea 2000 device on a spur, or • connec...
Page 59
4.16 camera / video in-out connection a camera / video device or external display can be connected to new e series multifunction displays (excluding the e7 / e7d) using the dedicated video in/out connector. Note: new a series and new c series multifunction displays do not have a dedicated video in/o...
Page 60
4.17 media player connection you can use your multifunction display to wirelessly control a bluetooth-compatible media player (such as a smartphone). The media player must be compatible with the bluetooth avrcp protocol (version 2.1 or higher). D12164-2 1 3 2 1. Multifunction display. 2. Bluetooth c...
Page 61
1. Select set-up. 2. Select system settings. 3. Select wireless connections. 4. Select connection manager. 5. Select the media player device in the list. 6. Select unpair / forget this device. 4.18 bluetooth remote control connection you can control the multifunction display wirelessly using a rayma...
Page 62
9. When prompted, press the arrow button on your remote that you wish to be configured as the up button. The other arrow button will automatically be configured as the down button. If the pairing was successful a “pairing success” message will be displayed. If a “pairing failure” or “pairing timeout...
Page 63
4.19 remote control functions ra n g e bu tto n s p a ir s e le c t o r d 12051-2 arrow buttons shortcut button button application where function available: default functions: chart radar fishfinder weather homescreen range / zoom. • press up or down arrow for momentary response. • hold up or down a...
Page 64
Reconnecting the rcu 1. When you pair the rcu-3 with a multifunction display a wireless connection is established. 2. When you power off the multifunction display it loses its connection with the rcu-3 after 10 minutes. > 10 minutes = 1 0 15 20 25 30 minutes 35 40 45 50 55 60 5 3. To restore the con...
Page 65
4.20 wifi connections raymarine mobile app connection you can use compatible tablet and smartphone devices as a wireless repeat display or remote control for your multifunction display. Raymarine apps allow you to stream and / or control, remotely what you see on your multifunction display to a comp...
Page 66
66 new a series / new c series / new e series.
Page 67
Chapter 5: location and mounting chapter contents • 5.1 selecting a location on page 68 • 5.2 mounting - new a series on page 69 • 5.3 mounting - new c series and new e series on page 71 location and mounting 67.
Page 68
5.1 selecting a location warning: potential ignition source this product is not approved for use in hazardous/flammable atmospheres. Do not install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). General location requirements when selecting a location for your pro...
Page 69
Vessel construction the construction of your vessel can have an impact on gps performance. For example, the proximity of heavy structure such as a structural bulkhead, or the interior of larger vessels may result in a reduced gps signal. Before locating equipment with an internal gps antenna below d...
Page 70
D12585-2 0 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Drill or knock out the 4 mounting holes on the unit d12588-1 0 0 0 0 0 0 3. Fix the appropriate cutting template supplied with the product, to the selected location, us...
Page 71
Display, ensuring that the clips along the bottom edge of the bezel latch into position. D 12586-1 4. Ensure the bezel is correctly aligned with the display, as shown. 5. Apply firm but even pressure to the bezel along the: i. Outer edges - work from the sides upwards and then along the top edge, to...
Page 72
1. Remove the front bezel. Refer to the separate instructions provided for that procedure. D12184-3 e7 / e7d 1 3 2 2. Remove the screws that secure the bezel to the display (only required for e7 and e7d). 3. Carefully remove the bezel from the rear of the display, pulling the bezel gently along the:...
Page 73
• attach the front bezel. D12273-2 1. Mark the location of the mounting bracket screw holes on the chosen mounting surface. 2. Drill holes for the fixings using a suitable drill, ensuring there is nothing behind the surface that may be damaged. 3. Use the fixings supplied with the mounting bracket t...
Page 74
74 new a series / new c series / new e series.
Page 75
Chapter 6: getting started chapter contents • 6.1 display power on page 76 • 6.2 new a series controls on page 76 • 6.3 e7 / e7d controls on page 77 • 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 controls on page 77 • 6.5 hybridtouch overview on page 79 • 6.6 touchscreen overview on ...
Page 76
6.1 display power powering the display on 1. Press the power button. 2. Select accept to acknowledge the disclaimer message. Powering the display on 1. Press the power button. 2. Press the ok button to accept the disclaimer message. Powering the display off 1. Press and hold the power button until t...
Page 77
6.3 e7 / e7d controls d12179-1 2 4 5 6 7 3 1 description functions 1 touchscreen you can touch the screen to operate many common functions, including all menu operations. 2 menu accesses menus. Press again to close menus. 3 unicontrol provides a joystick, rotary control and an ok push button for usi...
Page 78
D12180-1 1 2 3 1. Rotary — use this to select menu items, move the on-screen cursor, and adjust the range in the chart and radar applications. 2. Joystick — use this to move the cursor position in applications, pan up, down, left and right in the chart, weather and fishfinder applications or to cycl...
Page 79
6.5 hybridtouch overview if your multifunction display features hybridtouch, this enables you to operate the unit using the touchscreen and the physical buttons. A hybridtouch display has physical buttons which can be used in addition to the touchscreen. Touchscreen only multifunction displays (whic...
Page 80
6.7 homescreen overview — touch only displays the homescreen provides a central point of access to your display's range of applications. • the homescreen also provides quick access to your data (waypoints, routes, and tracks). • the homescreen consists of a number of application "pages", each repres...
Page 81
6.9 system checks gps check gps selection you can use an internal (if available) or external gps receiver. • your multifunction display may feature an internal gps receiver. • you can also connect an external gps receiver using seatalk ng or nmea 0183. • where appropriate use the system settings men...
Page 82
2. Select power so that on is highlighted. The radar scanner will now initialize in standby mode. This process will take approximately 70 seconds. 3. Select radar so that transmit is highlighted. The radar scanner should now be transmitting and receiving. 4. Check that the radar screen is operating ...
Page 83
Selecting the sonar transducer with the fishfinder application displayed: 1. Select menu. 2. Select set-up. 3. Select transducer set-up. 4. Select transducer. A list of transducers is displayed. 5. Select the transducer you want to use. Checking the sonar sonar checks are made using the fishfinder a...
Page 84
6.10 enabling autopilot control enabling the autopilot control function — seatalk and spx seatalk ng autopilots to enable control of your seatalk or spx seatalk ng autopilot using your multifunction display follow the steps below. From the homescreen: 1. Select set-up. 2. Select system settings. 3. ...
Page 85
6.12 pages pages are used to display applications. Pages are displayed and accessed on the homescreen. Each page can display more than 1 application. • you can set up and display up to 4 applications per page using a new c series, new e series or gs series (except for the e7 and e7d) multifunction d...
Page 86
4. Select the page that you want to delete. The page is deleted. Resetting the homescreen to default settings with the homescreen displayed: 1. Select the customize icon. 2. Select homescreen. 3. Select reset. A warning message is displayed asking for confirmation. 4. Select yes to reset the homescr...
Page 87
6.14 splitscreen controls when viewing a page with more than 1 application displayed you can switch applications from the splitscreen view to fullscreen view. Example 1 — splitscreen page example 2 — fishfinder application expanded to fullscreen selecting the active window — new a series and e7 / e7...
Page 88
6.15 screen overview d12196-1 5 4 1 2 3 8 6 7 screen item description 1 home • new a series — select the on-screen home icon to access the homescreen. • new c series — use the home button to go back to the previous menu. • e7 / e7d — press and hold the menu button for 3 seconds to access the homescr...
Page 89
Screen item description 1 back • displays with a touchscreen — select the on-screen back icon to go back to the previous menu. • non–touchscreen displays or hybridtouch — use the back button to go back to the previous menu. 2 menu item • displays with a touchscreen — momentarily touching a menu item...
Page 90
D12279-2 1 3 2 screen item description 1 status — provides status information for the connected equipment. For example, the pilot control dialog displays the locked heading and current navigation mode for a connected autopilot unit. 2 control icons — provide direct control of the connected equipment...
Page 91
6.17 editing numerical settings to edit numerical values you can use either the onscreen numeric adjust control, onscreen numeric keypad or the rotary control on a non-touch or hybridtouch display to increase or decrease numeric values. D12567-1 1 2 3 4 1. Select the numeric data field you want to e...
Page 92
6.19 databar status symbols the status symbols on the databar confirm whether the appropriate connections to your system have been made. The symbols show the status for the following: • radar scanner. • ais receiver / transceiver. • sonar module. • gps receiver. • autopilot. Radar scanner status sym...
Page 93
Symbol description power steering active. Wind vane mode is active. 6.20 initial set up procedures once your display has been installed and commissioned, raymarine recommends that you perform an initial set up procedure. Startup wizard when you power-up the display for the first time or after a syst...
Page 94
3. Touch the sun icon to increase the brightness level or the moon icon to decrease the brightness level. Note: the brightness level can also be increased by pressing the power button multiple times. Adjusting the display brightness 1. Press the power button once. The shortcuts menu is displayed. 2....
Page 95
6.21 software updates raymarine’s multifunction display software is updated regularly to provide new and enhanced features and improved performance and usability. You should ensure you have the latest software by regularly checking the raymarine website for new software. You can identify your multif...
Page 96
96 new a series / new c series / new e series.
Page 97
Chapter 7: managing display data chapter contents • 7.1 memory cards overview on page 98 • 7.2 inserting a memory card or chart card on page 98 • 7.3 removing a memory card or chart card on page 99 • 7.4 saving user data and user settings on page 99 • 7.5 screenshots on page 102 • 7.6 resetting your...
Page 98
7.1 memory cards overview you can use microsd memory cards to archive data (e.G. Waypoints and tracks). Microsd memory cards can be used to archive your data when the system capacity is reached. You can then delete old data from your system, creating capacity for new data. The archived data can be r...
Page 99
7.3 removing a memory card or chart card from the homescreen: 1. Select my data. 2. Select eject card. A message is displayed prompting you to select the memory device you want to eject. 3. Select sd1 for a memory card in the top card slot, or sd2 for a memory card in the bottom card slot. 4. Open t...
Page 100
Want to erase data from, if your display only has 1 card slot then you will not be prompted. 4. Select sd1 for a memory card in the top card slot, or sd2 for a memory card in the bottom card slot. 5. Select erase waypoints from card, erase routes from card, or erase tracks from card, as appropriate....
Page 101
Chart application — cartography settings application setting cartography data overlay cell 1 on / off data overlay cell 1 content data overlay cell 2 on / off data overlay cell 2 content chart object menu chart display chart grid 2d shading community layer chart text chart boundaries spot soundings ...
Page 102
7.5 screenshots you can take a screenshot of what is currently displayed on the screen. Screenshots are saved to a microsd card in .Bmp (bitmap) format. The saved image can be viewed from any device capable of viewing bitmap images. Taking a screenshot you can take a screenshot by following the step...
Page 103
Chapter 8: document viewer application chapter contents • 8.1 document viewer overview on page 104 document viewer application 103.
Page 104
8.1 document viewer overview your multifunction display includes a pdf document viewer. The document viewer is available from the homescreen and is used to view and search pdf documents (such as product handbooks). D12755-1 1 2 3 1 opens the sd card file browser. 2 opens the user manual stored on th...
Page 105
Note: you can also use the scroll bars to navigate through the document. Browsing an open document on hybridtouch and non-touch displays you can browse pdf documents by following the steps below. With a pdf document open: 1. Move the joystick up or down to move up and down through the document. 2. M...
Page 106
106 new a series / new c series / new e series.
Page 107
Chapter 9: autopilot control chapter contents • 9.1 autopilot control on page 108 • 9.2 pilot bar on page 110 • 9.3 pilot set-up on page 111 • 9.4 pilot settings on page 111 • 9.5 autopilot status symbols on page 116 • 9.6 autopilot alarms on page 116 autopilot control 107.
Page 108
9.1 autopilot control you can use your multifunction display to control your autopilot. If connected to an evolution autopilot then pilot settings will also be available. Note: for information on connecting your multifunction display to a raymarine autopilot system, refer to the documentation that a...
Page 109
Enabling autopilot control enabling the autopilot control function — seatalk and spx seatalk ng autopilots to enable control of your seatalk or spx seatalk ng autopilot using your multifunction display follow the steps below. From the homescreen: 1. Select set-up. 2. Select system settings. 3. Selec...
Page 110
1. Select any of the following options from the chart context menu: • goto waypoint • goto cursor • follow route • follow from here • follow route in reverse the pilot control dialog is displayed. 2. Select yes (track). Manually displaying the pilot control dialog box you can also open the pilot con...
Page 111
9.3 pilot set-up when connected to an evolution autopilot the pilot set-up page is available. D12883-1 9 1 0 4 6 7 5 8 2 1 3 1 back — go back to the previous menu. 2 pilot status — current pilot mode. 3 close — closes the pilot set-up page and displays the homescreen. 4 pilot control — switches auto...
Page 112
Selecting a drive type drive type selection is available from the dockside wizard, and also form the vessel settings menu: pilot set-up > pilot settings > vessel type > drive type. With the drive type menu displayed: 1. Select your drive type from the list. Note: the drive types available are depend...
Page 113
Setting the rudder limits on vessels fitted with a rudder reference transducer the rudder limits must be set. The rudder limit is used to set the rudder control. The rudder limits should be set to just inside the mechanical end stops to prevent unnecessary load on the steering system. Note: this pro...
Page 114
The following dockside wizard procedures only apply to vessels without a rudder reference transducer: • drive type selection. • rudder limit setting. • hard-over time setting (raymarine recommends that this information is specified once the dockside wizard and rudder drive check is complete, using t...
Page 115
Adjusting the hard-over time on vessels without a rudder reference transducer, it is important to set the hard-over time limits correctly, to ensure accurate autopilot operation. Hard-over time is the time it takes the vessel’s steering system to drive the rudder from full port to full starboard. Be...
Page 116
9.5 autopilot status symbols the autopilot status is indicated in the databar. Symbol description autopilot is in standby mode. Autopilot is in track mode. Autopilot is in auto mode. No autopilot detected. Autopilot alarm active. Dodge mode is active. Fish mode is active. Autopilot calibration. Powe...
Page 117
Chapter 10: alarms and man over board functions chapter contents • 10.1 using man overboard (mob) functions on page 118 • 10.2 alarms on page 119 alarms and man over board functions 117.
Page 118
10.1 using man overboard (mob) functions man overboard if you lose a person or object overboard, you can use the man overboard (mob) function to mark the position that the vessel was at when the mob function was activated. The mob function is available at all times, regardless of which application i...
Page 119
10.2 alarms alarms alert you to a situation or hazard requiring your attention. You can set up alarms to alert you to certain conditions, such as collision warnings and temperature limits. Alarms are raised by system functions, and also external equipment connected to your multifunction display. Whe...
Page 120
Alarms menu menu item description options mob data type determines whether position or dead reckoning (dr) data is displayed. Assuming that your vessel and the mob are subject to the same tide and wind effects, the dead reckoning setting normally gives a more accurate course. • dead reckoning • posi...
Page 121
Menu item description options • deep fish limit — specifies the upper value for the fish alarm depth limit. • 2 ft (or equivalent units) to the maximum of the transducer range deep fish limit • 2 ft (or equivalent units) to the maximum of the transducer range fuel manager in the fuel manager alarm o...
Page 122
122 new a series / new c series / new e series.
Page 123
Chapter 11: dsc vhf radio integration chapter contents • 11.1 using a dsc vhf radio with your display on page 124 • 11.2 enabling dsc vhf radio integration on page 124 dsc vhf radio integration 123.
Page 124
11.1 using a dsc vhf radio with your display you can connect your dsc vhf radio to your multifunction display and show distress message information and gps position data for other vessels. Connecting a dsc vhf radio to your multifunction display provides the following additional functionality: • dis...
Page 125: Chapter 12: Fuel Manager
Chapter 12: fuel manager chapter contents • 12.1 fuel manager overview on page 126 fuel manager 125.
Page 126
12.1 fuel manager overview the fuel manager provides an estimate of fuel remaining, and the distance and time which can be travelled before the tanks are empty. In order to calculate these values, you must configure the total capacity of fuel available to the engines and log each time you add fuel. ...
Page 127
Fuel logging you must ensure all fuel fills are recorded using the fuel manager. From the fuel manager page: 1. When filling the tanks until full select all tanks full. The estimated fuel remaining is reset to the value of your fuel tanks capacity. 2. When only partially filling the tank make a note...
Page 128
128 new a series / new c series / new e series.
Page 129: Chapter 13: Ais Function
Chapter 13: ais function chapter contents • 13.1 ais overview on page 130 • 13.2 ais prerequisites on page 131 • 13.3 ais context menu on page 131 • 13.4 enabling ais on page 132 • 13.5 displaying ais vectors on page 132 • 13.6 ais status symbols on page 133 • 13.7 ais silent mode on page 133 • 13.8...
Page 130
13.1 ais overview the ais feature enables you to receive information broadcast by other vessels, and to add these vessels as targets in the chart and radar applications. With an optional ais unit connected to your system you can: • display targets for any other ais-equipped vessels. • display voyage...
Page 131
13.2 ais prerequisites you must have suitable ais hardware connected to your multifunction display to make use of the ais functionality. In order to run ais, you will need: • a receive-only ais unit or a full ais transceiver (a unit that sends and receives). • a vhf antenna. • a gps - to provide pos...
Page 132
13.4 enabling ais enabling ais in the chart application to enable ais overlay in the chart application the chart view must be set to 2d menu > presentation > chart view. From the chart application: 1. Select menu. 2. Select presentation. 3. Select overlays. 4. Select ais: so that on is highlighted. ...
Page 133
13.6 ais status symbols ais status is indicated by a symbol in the databar. Symbol description ais unit is switched on and operating. Ais currently unavailable. Ais unit is switched off, or not connected. Ais unit is in silent mode. Ais unit is in silent mode, with active alarms. Ais unit is connect...
Page 134
13.8 ais target symbols your multifunction display shows a range of symbols to represent the different types of ais target. Target type description symbol transmitting target target is moving or at anchor (target is not activated, dangerous or lost). Activated target target activated — that is, ais ...
Page 135
13.10 viewing all ais targets • from the chart application with only the ais overlay enabled go to: menu > ais options. • from the chart application when the radar overlay is also enabled go to: menu > radar & ais options > view marpa & ais lists. • from the radar application go to menu > track targ...
Page 136
Enabling and disabling ais safety messages in the radar application from in the radar application: 1. Select menu. 2. Select track targets. 3. Select ais unit set-up. 4. Select ais safety messages. Selecting ais safety messages will switch between safety messages on and off. Displaying safety-critic...
Page 137
13.12 marpa & ais options parameter description options vector length the length of the vector lines displayed depends on the distance that an ais target travels in the time period that you specify for this setting. • 0.5 min • 1 min • 3 min • 6 min • 12 min • 30 min • 60 min target history targets’...
Page 138
13.13 ais alarms the ais functions generate a number of alarms to alert you to dangerous or lost targets. In addition to the dangerous target alarm, the system generates an alarm when a dangerous target becomes a lost target i.E. Its signal has not been received for 20 seconds. Your ais receiver gen...
Page 139
Adding a vessel to your buddy list in the chart or radar application: 1. Select the ais target. The ais target context menu is displayed. 2. Select add buddy. I. Select yes to enter a name for the buddy vessel ii. Select no to save the vessel to your buddy list without entering a name for the buddy ...
Page 140
140 new a series / new c series / new e series.
Page 141
Chapter 14: waypoints, routes and tracks chapter contents • 14.1 waypoints on page 142 • 14.2 routes on page 147 • 14.3 tracks on page 150 • 14.4 waypoints, routes and tracks storage capacity on page 152 waypoints, routes and tracks 141.
Page 142
14.1 waypoints a waypoint is a position marked on the screen to indicate a site or a place to navigate to. As well as acting as position markers, waypoints are also the building blocks used to create routes. Common waypoint functions are accessed using the waypoints menu. This can be shown at any ti...
Page 143
• measure • build route • acquire target (only available if radar overlay is switched on.) • slew thermal camera (only available when thermal camera is connected and operating.) accessing the context menu you can access the context menu by following the steps below. 1. Non-touchscreen and hybridtouc...
Page 144
Navigating to a waypoint on the screen d 11753-2 from the chart or radar application: 1. Select the waypoint. The waypoint context menu is displayed. 2. Select the goto waypoint. Note: with an active waypoint selected you can select stop goto option from the waypoint context menu at any time to canc...
Page 145
4. Use the on-screen keyboard to make the changes, then select the on-screen keyboard's save button. Editing a waypoint using the context menu 1. Select the waypoint. The waypoint context menu is displayed. 2. Select edit waypoint. The edit waypoint dialog is displayed. 3. Select the field you want ...
Page 146
Waypoint groups in order to make your waypoints easier to manage, you can organize them into groups of your choice. When fishing, for example, you may only wish to see the waypoints that indicate good fishing sites. Provided that you have not changed the default group, all waypoints are automaticall...
Page 147
14.2 routes a route is a series of waypoints typically used to assist with passage planning and navigation. A route is displayed on screen as a series of waypoints linked by a line. D 11750-1 route features there are a range of route features for building, navigating and managing routes. The route f...
Page 148
1. Use the range in and range out buttons to range in and out of the chart. Adjusting chart range while building a route from the build route menu: 1. Use the on-screen range in and range out icons to range in and out of the chart. Build a route from a track you can create a route from a recorded tr...
Page 149
• from a selected waypoint or any leg within a route. You can also follow any route in reverse order. Following a stored route from the chart application: 1. Select menu. 2. Select navigate. 3. Select follow route. The route list is displayed. 4. Select the route you want to follow. 5. Select follow...
Page 150
Moving a waypoint within a route from the chart application: 1. Position the cursor over the waypoint you want to move. The waypoint context menu is displayed. 2. Select move waypoint. 3. Select the new location for the waypoint. Erasing routes erasing a displayed route from the chart application: 1...
Page 151
• auto— the track interval is automatically set (auto will minimize track points whilst maintaining correlation between the track and the actual path followed). • time— the track points are placed at regular intervals of time. • distance— the track points are placed at regular intervals of distance....
Page 152
14.4 waypoints, routes and tracks storage capacity the display can store the following quantities of waypoints, routes and tracks way- points • 3000 waypoints • 100 waypoint groups routes • 150 routes, each consisting of up to 50 waypoints. Tracks • 15 tracks, each consisting of up to 10000 track po...
Page 153
Chapter 15: chart application chapter contents • 15.1 chart application overview on page 154 • 15.2 chart ranging and panning on page 155 • 15.3 vessel position and orientation on page 156 • 15.4 chart views on page 158 • 15.5 chart context menu on page 159 • 15.6 my data options on page 160 • 15.7 ...
Page 154
15.1 chart application overview the chart application provides an electronic chart with passage planning and navigation features. It combines 2d and 3d viewpoints and provides a variety of cartographic information regarding your surroundings and charted objects. Typical uses for the chart applicatio...
Page 155
Navionics chartplotter sync connection you can wirelessly synchronize waypoints and routes between the multifunction display and a tablet or smartphone device. D12166-2 1 3 4 2 1. Multifunction display. 2. Wi-fi connection. 3. Tablet / smartphone. 4. Navionics marine app. To use this feature you mus...
Page 156
15.3 vessel position and orientation vessel position on the chart display your current position is represented on screen by the vessel symbol. The symbol used for your vessel will vary depending on the vessel type selected during initial set up of your multifunction display. Motor vessels sail vesse...
Page 157
Note: in the 3d chart view, only relative motion mode is available. The current motion mode applies to the active instance of the chart application. When you pan the chart the motion mode is no longer active. This is indicated in the status bar by brackets around the motion mode — for example, (rela...
Page 158
15.4 chart views switching between 2d/3d chart view you can switch between 2d and 3d views. From the chart application: 1. Select menu. 2. Select presentation . 3. Select chart view to switch between 2d or 3d. 2d chart view the 2d chart view can display a range of information to help you navigate. D...
Page 159
Ii. Hybridtouch or touch only displays — swipe your finger up or down across the screen to adjust the pitch. D 11755-1 4. To adjust the rotation: i. Non-touchscreen or hybridtouch displays — move the joystick left or right to adjust the rotation ii. Hybridtouch or touch only displays — swipe your fi...
Page 160
15.6 my data options the chart provides features to help you manage your data and help plan your navigation to a chosen location. The options are found in the my data menu: menu > my data. • waypoint list — view and edit waypoints stored on the system. • route list — view and edit routes stored on t...
Page 161
15.8 measuring distances and bearings you can use the databar and context menu information you can use the measure function to measure distances in the chart application. You can determine the distance and bearing: • from your vessel to the position of the cursor; • between two points on the chart. ...
Page 162
15.10 current information animated current information the electronic charts may allow animation of the current information current stations. D 11748-3 animated current information is available in the chart application wherever a diamond-shaped symbol with a "c" is displayed: this symbol identifies ...
Page 163
15.11 tide information animated tide information the electronic charts may allow animation of the tide information tide stations. Animated tide information is available in the chart application wherever a diamond-shaped symbol with a "t" is displayed: this symbol identifies tide stations and the ava...
Page 164
15.12 chart object information you can display additional information on the chart for cartographic objects, ports, and marinas. You can also search for the nearest instance of a particular chart object and search for ports by name. Depending on the chart card you are using, you can view some or all...
Page 165
15.13 chart presentation the chart has a number of presentation options which affect the level of detail, types of objects and how the chart application appears onscreen. The presentation options available are: • chart detail — set the level of object detail shown on the chart. • easy view — easy vi...
Page 166
4. Select either on land, on land and shallows, or on land and sea. A tick is displayed next to the option and if aerial overlay is switched on the screen is redrawn showing the new overlay selection. Radar overlay you can overlay radar and marpa functions in the chart application to provide target ...
Page 167
Range rings give you an incremental representation of distance from your vessel to help you judge distances at a glance. The rings are always centred on your vessel, and the scale varies to suit your current zoom setting. Each ring is labelled with the distance from your vessel. Enabling range rings...
Page 168
• transducer cone — switches on and off a transducer cone indicating the coverage of a fishfinder transducer. • depth scale — switches on and off a depth scale at your vessel position. Enabling center of view to enable the center of view cross hair at sea level follow the steps below: in 3d view: 1....
Page 169
15.14 selecting the cartography set-up menu from the homescreen: 1. Select set-up. 2. Select cartography. The cartography menu options are displayed. Chart application 169.
Page 170
15.15 cartography set-up menu options the following table describes the various options in the cartography set-up menu for your multifunction display. Menu item description options chart display determines the level of detail shown on the chart. • simple • detailed (default) • extra detailed chart g...
Page 171
Menu item description options nav. Marks determines whether navigation marks are displayed on the chart: • off — navigation marks are not displayed. • on — navigation marks are displayed. • off • on (default) nav. Mark symbols determines which set of navigation mark symbols is used — international, ...
Page 172
172 new a series / new c series / new e series.
Page 173
Chapter 16: radar application chapter contents • 16.1 radar overview on page 174 • 16.2 radar scan speed on page 175 • 16.3 radar scanner status symbols on page 175 • 16.4 radar range and image quality on page 176 • 16.5 radar display overview on page 178 • 16.6 dual range radar operation on page 17...
Page 174
16.1 radar overview radar is used to provide information that can help you to track targets and measure distances and bearings. Radio detection and ranging (radar) is used at sea to detect the presence of objects (known as ‘targets’) at a distance, and if they are moving, detect their speed. Radar w...
Page 175
16.2 radar scan speed superhd open array radars with software version 3.23 or above or hd radomes support multiple scan speeds. Radar scan speed is set up using the radar set-up menu. When the system detects a scanner that is capable of operating at both 24 rpm and 48 rpm, 2 options are provided for...
Page 176
2. Select power up radar to turn the radar on, or power down radar to turn the radar off. 3. Select radar: tx to start the radar transmitting, or radar: stdby to stop the radar transmitting. 16.4 radar range and image quality maximum radar range the usable range of the radar is limited by factors su...
Page 177
D1638-5 1 2 2 3 4 5 6 6 item description 1 main lobe 2 side lobes 3 antenna 4 arc 5 true echo 6 side echoes indirect echoes there are several types of indirect echoes or ghost images. These sometimes have the appearance of true echoes, but in general they are intermittent and poorly defined. D1641-5...
Page 178
Sea clutter off sea clutter in auto interference when two or more radar-equipped vessels are operating within range of each other mutual radar interference can occur. This usually appears as a spiral of small dots from the display centre this type of interference is most noticeable at long ranges. T...
Page 179
Is dependent on many factors and may not necessarily be proportional to its physical size. Nearby objects may appear to be the same size as distant larger objects. Note: colors stated above refer to the default color palette. With experience, the approximate size of different objects can be determin...
Page 180
Scanner dual range mode operating mode 4 kw superhd open array long superhd short hd 12 kw superhd open array long superhd short hd enabling dual range radar operation in the radar application. 1. Select menu. 2. Select presentation. 3. Select dual range so that on is highlighted. Selecting dual ran...
Page 181
Course-up n n 1 2 d 12210-1 item description 1 current course upwards. 2 as your vessel's heading changes: • radar picture is fixed • shm rotates accordingly if you select a new course, the picture will reset to display the new course upwards. The reference used for course-up depends upon the inform...
Page 182
16.8 radar tuning: on-screen gain controls touchscreen multifunction displays provide on-screen access to controls for gain, rain and sea clutter. Gain control rain control sea control note: non-touchscreen controls are accessed by the menu options: menu > rain and menu > adjust gain. Enabling and d...
Page 183
16.9 radar adjustments: hd and superhd scanners you can use the gain presets and other functions to improve the quality of the radar picture. The following settings are available from the radar menu and apply to hd radomes, hd and superhd open array scanners: menu item description options auto gain ...
Page 184
6. Select the auto box so that a tick is placed in the box for automatic gain control. Adjusting radar anti sea clutter from the radar application, with the required auto gain mode selected: 1. Select menu. 2. Select adjust gain , where shall be the auto gain mode already selected. 3. Select sea: . ...
Page 185
16.10 radar adjustments: non-hd digital radomes you can use the gain presets and other functions to improve the quality of the radar picture. The following settings apply to non-hd digital radomes and are available from the radar menu: menu item description options rain the radar scanner detects ech...
Page 186
16.11 radar presentation menu options function description options dual range this menu item allows you to turn dual range mode on and off. • on • off dual range channel this menu item allows you to choose long or short channel for dual range. • 1 • 2 orientation & motion mode this menu item contain...
Page 187
Function description options databoxes set-up this menu item contains a sub-menu which enables you to turn on and select information to display in data cells located on the bottom left of the radar application (data cells will be displayed in all radar windows). • data cell 1 • select data category ...
Page 188
True motion mode example d12745-1 2 3 1 4 d r a ft d r a ft d r a ft t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e t e...
Page 189
16.12 using radar to measure distances, ranges, and bearings when you are using the radar application, you can measure distances, ranges and bearings in a variety of ways. These options are detailed in the table below: functions distances between points range from your vessel bearings range rings ye...
Page 190
Vrm/ebl context menu the vrm/ebl function includes a context menu which provides positional data and menu items. The context menu provides positional data of the vrm/ebl in relation to your vessel: • range • bearing the context menu also provide the following menu items: • float centre • adjust • vr...
Page 191
16.13 using radar to track targets and avoid collisions the guard zone , vrm/ebl and marpa functions will help you track targets and avoid collisions. With a radar connected to your multifunction display, you can: • assess how far away a target is and its bearing (vrm/ebl). • set an alarm to trigger...
Page 192
There are conditions where acquiring a target may become difficult. These same conditions may be a factor in successfully tracking a target. Some of the conditions are: • the target echo is weak. The target is very close to land, buoys or other large targets. • the target or your own vessel is makin...
Page 193
Cancelling a marpa target using the marpa context menu from the radar application: 1. Select the relevant target. The marpa context menu is displayed. 2. Select cancel target or cancel all targets. Cancelling a marpa target using the menu 1. Select menu. 2. Select track targets. 3. Select view marpa...
Page 194
16.14 radar set-up menu the radar set-up menu enables you to configure the performance and behavior of your radar scanner. Function description options timed transmit set-up this menu item contains a sub-menu that enables you to adjust the timed transmit options: • timed transmit • transmit period •...
Page 195
16.15 resetting the radar to reset radar settings to defaults follow the steps below: from in the radar application: 1. Select menu. 2. Select radar set-up. 3. Select advanced. 4. Select reset advanced. A confirmation pop up message is displayed. 5. Select yes to confirm reset. Radar application 195.
Page 196
196 new a series / new c series / new e series.
Page 197
Chapter 17: fishfinder application chapter contents • 17.1 how the fishfinder works on page 198 • 17.2 raymarine sonar modules on page 198 • 17.3 traditional sonar technology on page 199 • 17.4 chirp technology on page 199 • 17.5 fishfinder introduction on page 200 • 17.6 transducer bandwidth on pag...
Page 198
17.1 how the fishfinder works the fishfinder application uses a sonar module and a suitable sonar transducer. The sonar module interprets signals from the transducer and builds up a detailed underwater view. The transducer is located on the bottom of the boat, it sends pulses of sound waves into the...
Page 199
17.3 traditional sonar technology traditional sonar uses a single carrier frequency or carrier wave for the sonar ping. The sonar works by measuring the time it takes the ping echo to return to the transducer to determine target depth. D12600-1 17.4 chirp technology chirp sonars use a swept frequenc...
Page 200
17.5 fishfinder introduction warning: sonar operation • never operate the sonar with the vessel out of the water. • never touch the transducer face when the sonar is powered on. • switch off the sonar if divers are likely to be within 7.6 m (25 ft) of the transducer. Fishfinder overview the fishfind...
Page 201
17.6 transducer bandwidth the fishfinder application displays the fishfinder frequency, center frequency or chirp mode depending on the connected sonar module and transducer. Example of chirp sonar module in chirp mode. • when using a chirp sonar module set to chirp mode and a wide band transducer t...
Page 202
Water depth as water depth increases signal strength decreases, resulting in a lighter onscreen image of the bottom. Size of the target the larger the target, the larger the return on the fishfinder display. The size of a fish target is also dependent upon the size of the fish’s swim bladder rather ...
Page 203
17.9 dual / single frequency fishfinder dual frequency operation allows the sonar to operate and display 2 frequencies simultaneously. If the preset mode that you are using has two frequencies configured, you can view either one or both of those frequencies in separate windows. Selecting dual freque...
Page 204
The graph above depicts an example of the fine tuning (from —50% to +50%) available when the frequency is set to 200 khz. Tuning the fishfinder frequency (non-chirp sonar module) when connected to a non-chirp sonar module you can manually tune the fishfinder frequency. From the fishfinder applicatio...
Page 205
Frequency adjustment (chirp sonar module in non-chirp mode) when using a chirp sonar module in chirp mode (low chirp, med chirp or high chirp) the frequency cannot be adjusted. When using a chirp sonar module in a non-chirp mode (e.G. 50 khz or 160 khz) the frequency at which the transducer is trans...
Page 206
17.12 fishfinder display modes selecting a fishfinder display mode from the fishfinder application: 1. Select menu. 2. Select display mode. 3. With dual frequency preset set, select adjust to select which frequency display you wish to change. Selecting adjust in dual frequency preset will switch bet...
Page 207
Bottom lock the bottom lock function applies a filter to flatten the image of the seabed and make any objects on or just above it easier to see. This feature is particularly useful for finding fish that feed close to the bottom. Adjusting the range of the bottom lock image allows you to view more bo...
Page 208
• rmk-9 keypad slide the screen up or down • new a series • new e series • gs series using range shift the default setting adjusts the display to keep the bottom in the lower half of the display window. Alternatively you can shift the image within the current range. Changes to the range shift are re...
Page 209
• trolling (med) • fishing (high) 4. Select the required auto gain mode. Fishfinder gain on-screen controls touchscreen multifunction displays provide on-screen access to the gain controls. Selecting the on-screen gain control will display the gain settings: when connected to a non-chirp sonar modul...
Page 210
2. Select sensitivity settings. 3. Select tvg. 4. Select adjust. 5. Select frequency 1, frequency 2 or both. Selecting a preset tvg setting tvg preset options are only available when connected to a raymarine chirp sonar module. With tvg set to auto, from the fishfinder application: 1. Select menu. 2...
Page 211
Fishfinder power the power setting controls the power level of the transducer. Power options: • auto. This is the default setting. When it is selected the sonar module automatically determines the required power setting based on the current depth, speed, and (bottom) signal strength. . • manual. If ...
Page 212
Menu item description options gain controls controls whether or not the on-screen gain and tvg controls are shown or not note: gain controls setting is only available on touchscreen multifunction displays. • show (default) • hide databoxes set-up allows you to set up and display/hide up to 2 databox...
Page 213
Fishfinder marker context menu the fishfinder marker includes a context menu which provides marker information and menu items. The context menu provides data for the position of the marker: • depth • range the context menu also provides the following menu items: • place waypoint • move marker • eras...
Page 214
17.18 fishfinder waypoints placing a waypoint on the fishfinder display enables you to mark a position so that you can return to it later. When a waypoint is placed, its details are added to the waypoint list and a vertical line labelled wpt is displayed on-screen. The waypoints can then be navigate...
Page 215
17.20 sounder set-up menu options this section describes the settings you can change using the sounder set up menu: (menu > set-up > sounder set-up). The set up menu contains settings that are likely to be changed infrequently. Menu item description options internal sounder switch the built in sonar...
Page 216
17.21 transducer set-up menu options the transducer set-up menu should be used when setting up your multifunction display for the first time or when installing a depth transducer. Menu item description options transducer select the appropriate transducer type from those displayed. Some transducers m...
Page 217
Fishfinder transducer calibration your fishfinder transducer must be calibrated correctly to achieve accurate depth readings. The multifunction display receives the image from a sonar module which processes sonar signals from a transducer mounted in the water. If the transducer is equipped with a sp...
Page 218
17.22 resetting the sonar the reset function restores the unit to its factory default values. Note: performing a factory reset will clear speed and temperature calibration settings and the depth offset. 1. Using a compatible raymarine multifunction display go to the fishfinder application page. 2. S...
Page 219
Chapter 18: data application chapter contents • 18.1 data application overview on page 220 • 18.2 selecting datapages using touch on page 221 • 18.3 selecting datapages on page 222 • 18.4 customizing the data application on page 222 • 18.5 resetting minimum and maximum readings on page 229 • 18.6 re...
Page 220
18.1 data application overview the data application enables you to view data generated by the multifunction display or data that is available on your system. Data can be obtained from devices connected using seatalk hs , seatalk ng or nmea protocols. Pre-configured datapages by default, a pre-config...
Page 221
Datapage 7 inch displays and below 9 inch displays and above fuel • port coolant temperature • port oil pressure • port fuel remaining • starboard coolant temperature • starboard oil pressure • starboard fuel remaining • port rpm • port alternator • starboard rpm • starboard alternator note: the dat...
Page 222
18.3 selecting datapages to select datapages using a non-touch multifunction display follow the steps below. From the data application: 1. Move the joystick down to goto the next page, or 2. Move the joystick up to goto the previous page. 18.4 customizing the data application you can customize the d...
Page 223
4. Enter the new name for the datapage. 5. Select save. Adding a new datapage you can add your own customized datapages to the data application. The total number of datapages including pre-configured pages is 10. From the data application: 1. Select menu. 2. Select create new page. A list of availab...
Page 224
Units set-up you can specify your preference for the units of measurement that will be used in all applications. Menu item description options distance units the units of measure that will be used in all applications for the display of all values related to distance. • nautical miles • statute miles...
Page 225
List of data items depending on connected devices the categories of data available to display in the data application, data overlay, databar, and expanded databar are shown below. The following table shows the data items available by category. Data category description data item digital dials* graph...
Page 226
Data category description data item digital dials* graphical* fuel flow (inst) fuel flow (avg) engine hours engine trim alternator engine load fuel level (%) fuel level (vol) total fuel (%) total fuel (vol) fuel flow total economy estimated fuel remaining distance to empty time to empty fuel used (t...
Page 227
Data category description data item digital dials* graphical* minimum water temperature maximum water temperature vessel position cog & sog cog sog maximum sog gps gps-related data. For example, vessel position. Average sog heading heading and speed (data application only.) locked heading locked hea...
Page 228
Data category description data item digital dials* graphical* distance made good estimated time of arrival wpt ttg course to steer pilot pilot-related data. For example, rudder. Rudder angle speed maximum speed average speed speed and sog trolling speed vmg to windward speed speed-related data. For ...
Page 229
Data category description data item digital dials* graphical* minimum tws twd twa & tws twa (ch) and tws twa and vmg awa & aws awa (ch) and aws awa and vmg awa and twa beaufort cardinal wind ground wind gwd & gws gwd and beaufort none note: *dials and graphical representations are only available fro...
Page 230
230 new a series / new c series / new e series.
Page 231
Chapter 19: thermal camera application — pan and tilt cameras chapter contents • 19.1 thermal camera application overview on page 232 • 19.2 thermal camera image on page 232 • 19.3 controls overview on page 233 • 19.4 camera control on page 234 • 19.5 image adjustments on page 236 • 19.6 pan and til...
Page 232
19.1 thermal camera application overview the thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions. For example,...
Page 233
Icon description rear-view mode — image is flipped horizontally. Zoom setting: 2x zoom. Zoom setting: 4x zoom. Single active controller on network. Multiple active controllers on network. Pc / laptop detected on network. Point mode enabled. Point mode disabled. Stabilization off. Stabilization on. F...
Page 234
19.4 camera control power up and standby when the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in standby mode. In order for the camera to operate, you must bring the camera out of standby mod...
Page 235
Surveillance mode settings the scan width and scan speed can be adjusted. Scan width the scan width determines the distance that the camera pans left and right when in surveillance mode. Scan speed the scan speed determines the speed at which the camera pans left and right when in surveillance mode....
Page 236
19.5 image adjustments adjusting the thermal camera image with the thermal camera application displayed: 1. Select menu. 2. Select adjust contrast. 3. Select the contrast, brightness, or color option as appropriate. The relevant numeric adjust control is displayed. 4. Adjust the value as required. 5...
Page 237
3. Use the image type menu item to switch between ir and visible light views, as appropriate. Thermal camera rear view mode the rear view mode flips the video image horizontally, providing a “mirror image”. This is useful for example in instances where the camera is rear-facing and you are viewing t...
Page 238
19.6 pan and tilt camera — new camera interface the thermal camera application menu options for a pan and tilt thermal camera with the new camera interface are shown below. Activate camera brings the thermal camera out of standby mode. (only available when camera is in standby.) pause image • on • o...
Page 239
Camera set-up menu set home position sets the camera’s current position as the camera home position. Slew settings provides automatic slew options and camera alignment settings. • auto slew to mob • auto slew to dangerous ais target • auto slew to dangerous marpa target • camera height above sea lev...
Page 240
Note: the thermal camera menu options available are dependant on the software version of your multifunction display and thermal camera. If options are different than listed above please refer to the manual that accompanied your thermal camera and / or the installation and operations handbook which a...
Page 241
19.7 high power and high torque modes camera state camera setting dual payload single payload standby • high power mode on • high torque mode on 22 w 17.4 w standby • high power mode off • high torque mode on 8 w 7.4 w standby • high power mode on • high torque mode off 13 w 13 w awake • high power ...
Page 242
19.8 pan and tilt camera — old camera interface the thermal camera application menu options for a pan and tilt thermal camera with the old camera interface are shown below. Activate camera brings the thermal camera out of standby mode. (only available when camera is in standby.) pause image • on • o...
Page 243
System setup settings to optimize operation for this particular system / installation. About / help helpful information and restore to factory defaults setting. Exit cancels on-screen menu. Video setup menu menu item / description settings / operation set thermal color default this saves the current...
Page 244
Menu item / description settings / operation set stow position this option sets the current position as the stow position. The camera moves to the stow position whenever it is turned off or put into standby mode. Name camera use this option to name the camera. Surveillance mode this options enables ...
Page 245
Chapter 20: thermal camera application — fixed mount cameras chapter contents • 20.1 thermal camera application overview on page 246 • 20.2 thermal camera image on page 246 • 20.3 controls overview on page 247 • 20.4 camera control on page 248 • 20.5 image adjustments on page 248 • 20.6 fixed mount ...
Page 246
20.1 thermal camera application overview the thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions. For example,...
Page 247
Icon description zoom setting: 4x zoom. Single active controller on network. Multiple active controllers on network. Pc / laptop detected on network. Ffc (flat field correction) periodically the camera will perform a flat field correction (ffc). This will fine tune the thermal image to suit the curr...
Page 248
20.4 camera control power up and standby when the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in standby mode. In order for the camera to operate, you must bring the camera out of standby mod...
Page 249
Thermal camera reverse video you can reverse the polarity of the video image to change the appearance of objects on-screen. The reverse video option (video polarity) switches the thermal image from white-hot (or red-hot if the color mode setting is active) to black-hot. The difference between white-...
Page 250
20.6 fixed mount camera menu the thermal camera application menu options for a fixed mount thermal camera are shown below. Activate camera brings the thermal camera out of standby mode. (only available when camera is in standby.) pause image • on • off (default) image options select to display the i...
Page 251
Jcu icon shows or hides the on-screen jcu connected icon. • on (default) • off pc icon shows or hides the on-screen pc connected icon. • on (default) • off restore factory defaults enables you to restore the camera’s settings to factory default values. Note: the thermal camera menu options available...
Page 252
252 new a series / new c series / new e series.
Page 253
Chapter 21: camera application chapter contents • 21.1 camera application overview on page 254 • 21.2 camera cycling on page 255 • 21.3 naming camera / video feeds on page 255 • 21.4 adjusting the video image on page 256 • 21.5 selecting the aspect ratio on page 256 • 21.6 selecting a location to st...
Page 254
21.1 camera application overview you can view a camera or a video feed which is connected directly to your multifunction display using the video input(s), or ip camera feeds which are available on your network. The camera application can be used to: • display live camera feeds. • automatically cycle...
Page 255
21.2 camera cycling when multiple camera / video feeds are available the camera application can be set up to automatically cycle through the available feeds at a specified time interval. With camera cycling turned on the camera application will cycle through the available video input(s) on the displ...
Page 256
21.4 adjusting the video image if supported by your connected camera / video input device or networked ip camera, you can adjust the image settings. With a video feed displayed in the camera application: 1. Select menu. 2. Select adjust. 3. Select contrast, brightness, or color, as appropriate. The ...
Page 257
21.6 selecting a location to store recordings in order to record, playback or capture a still image of ip camera feeds you must select the location you want to save to. If saving to a memory card ensure that a memory card with sufficient space is inserted into the relevant card reader slot. Note: do...
Page 258
6. Select play video. The video file is played. You can also playback video clips from the my data menu from the homescreen: homescreen > my data > images and videos. Moving and copying video files you can copy and move files between your display’s internal storage and memory cards using the steps b...
Page 259
6. Select start timer. The photo will be taken after the time delay specified has elapsed. A confirmation dialog is then displayed showing a preview of the photo taken. 7. Select ok to confirm. 8. Select view to view the photo fullscreen. 9. Select delete to delete the photo. Taking a photo using a ...
Page 260
21.9 onscreen icons on touchscreen multifunction displays you can touch anywhere on the screen to display the onscreen icons the onscreen icons can be used to start / stop recording or to take a picture. Record icon stop recording icon take photo icon the onscreen icons will close after 5 seconds. U...
Page 261
Chapter 22: fusion link application chapter contents • 22.1 fusion link overview on page 262 • 22.2 media sources on page 263 • 22.3 browsing music on page 265 • 22.4 selecting shuffle and repeat functions on page 265 • 22.5 adjusting volume levels for each zone on page 266 • 22.6 selecting the zone...
Page 262
22.1 fusion link overview the multifunction display can control a connected 700 series fusion entertainment system. D12746-1 1 5 7 4 3 6 2 1 fusion menu options and track lists. 2 shuffle and repeat icons. 3 track / media specific details and controls. 4 zone volume control. 5 zone selector. 6 media...
Page 263
22.2 media sources the layout and controls available are determined by the selected media source. Ipod d12748-1 1 4 2 3 5 6 1 album artwork. 2 track title. 3 artist. 4 track progress. 5 track number. 6 album title. Menu options available for ipods are as follows: • browse music. • repeat. • shuffle....
Page 264
Vhf d12753-1 1 3 2 1 squelch control. 2 channel. 3 manual / auto status. Menu options available for vhf radios are as follows: • preset. • scan. • tone controls. • select fusion system. Aux d12754-1 1 1 input gain. Menu options available for aux devices are as follows: • tone controls. • select fusi...
Page 265
22.3 browsing music you can browse the music available on your connected ipod or usb device. From the fusion link application: 1. Select the menu icon. 2. Select browse music. The media device name is displayed. 3. Select the media device. The contents of the device are displayed. 4. Browse the avai...
Page 266
22.5 adjusting volume levels for each zone the volume level for each zone can be adjusted individually or you can adjust all zones at the same time. From the fusion link application: 1. Select vol:. The zone volume control is displayed. 2. Select the relevant zone. 3. Adjust the volume level to the ...
Page 267
22.7 adjusting the tone controls the bass, middle, and treble tone controls can be adjusted. From the fusion link application: 1. Select the menu icon. 2. Select tone controls. 3. Select either bass, middle, or treble. 4. Adjust the level to the required setting. 5. Select back to go back to the men...
Page 268
22.9 menu options menu option media sources description browse music • ipod. • usb. Enables browsing of music stored on the device. Repeat • ipod. • usb. • off • folder — repeats all songs in the current folder. Shuffle • ipod. • usb. Switches track shuffle on and off. Tone controls • all devices. E...
Page 269
Chapter 23: weather application (north america only) chapter contents • 23.1 weather application overview on page 270 • 23.2 weather application set up on page 270 • 23.3 weather application display overview on page 271 • 23.4 weather map navigation on page 274 • 23.5 weather context menu on page 27...
Page 270
23.1 weather application overview the weather application overlays historical, live, and forecasted weather graphics on a world map. The weather application can only be used in north america and its coastal waters. The weather application graphics and their associated weather data enable you to dete...
Page 271
23.3 weather application display overview the weather application displays a range of graphics to indicate weather conditions and forecast information. The following diagram illustrates the main features of the weather application display: d 8564-3 5 7 1 0 6 9 8 1 2 3 4 1 1 1 1 item description 1 ra...
Page 272
Historical (grey) current (red) forecast (orange) description hurricane (category 1–5) tropical storm tropical disturbance, tropical depression when a symbol is selected, additional storm information can be accessed by the context menu: • storm's name and type. • date and time. • position, direction...
Page 273
Nowrad precipitation color codes nowrad displays the type and level of precipitation: color code precipitation type reflectivity intensity light green rain (15 to 19 dbz) medium green rain (20 to 29 dbz) dark green rain (30 to 39 dbz) yellow rain (40 to 44 dbz) orange rain (45 to 49 dbz) light red r...
Page 274
23.4 weather map navigation you can move around the weather map and place waypoints. When you open the weather application, a world map is displayed. If the system has a position fix for your vessel, the map will be centred on your location. As in the chart application, use the cursor to move around...
Page 275
23.6 weather information you can view weather information for: • a specific location • a surface observation station (when displayed) • cities (when displayed) viewing weather data at a specific location you can view weather details at a particular location on the world map regardless of the display...
Page 276
1 d 12297-1 item description 1 watchbox alert box viewing watchbox alerts you can view a watchbox alert at any time by following the steps below: from the weather application with a watchbox alert box displayed. 1. Select the watchbox alert box. The context menu is displayed. 2. Select view data. Th...
Page 277
23.9 weather application menu options the following options are available from the weather application menu: menu item description options find ship selecting find ship will reset the display to show your vessel in the center of the screen. Display graphics the display graphics menu allows to choose...
Page 278
23.10 glossary of weather terms term definition cold front the boundary between two different air masses where cold air pushes warm air out of the way and brings colder weather. Cyclone a large area of low atmospheric pressure, characterized by inward spiralling winds. A “low” also called a “depress...
Page 279
Term definition typhoon the name for a tropical storm originating in the pacific ocean, usually the china sea. They are basically the same as the hurricanes of the atlantic ocean and the cyclones of the bay of bengal. Wave cyclone a storm or low pressure centre that moves along a front. Wave period ...
Page 280
280 new a series / new c series / new e series.
Page 281
Chapter 24: sirius audio application (north america only) chapter contents • 24.1 sirius audio overview on page 282 sirius audio application (north america only) 281.
Page 282
24.1 sirius audio overview a connected, compatible raymarine sirius marine weather / satellite radio receiver can be controlled using the sirius audio application. Note: a sirius subscription is required to enable use of a sirius marine weather / satellite radio receiver. To enable volume controls t...
Page 283
Chapter 25: mobile applications chapter contents • 25.1 raymarine mobile apps on page 284 • 25.2 enabling wi-fi on page 285 • 25.3 enabling mobile apps on page 285 • 25.4 setting up wi-fi security on page 286 • 25.5 selecting a wi-fi channel on page 286 mobile applications 283.
Page 284
25.1 raymarine mobile apps raymarine mobile apps enable viewing and control of your multifunction display via a compatible mobile device, using a wi-fi connection. Raymarine currently offers the following mobile apps: • rayview • rayremote • raycontrol note: your multifunction display must have soft...
Page 285
25.2 enabling wi-fi with the homescreen displayed: 1. Select set-up. 2. Select system settings. 3. Select wireless connections. 4. Select wi-fi > on. 25.3 enabling mobile apps raymarine mobile apps must be enabled on your multifunction display before you can stream video or remote control your multi...
Page 286
25.4 setting up wi-fi security you can encrypt the wi-fi connection on the multifunction display to prevent unauthorized devices from accessing the connection. The default encryption is wpa2. With the homescreen displayed: 1. Select set-up. 2. Select system settings. 3. Select wireless connections. ...
Page 287
Chapter 26: customizing your display chapter contents • 26.1 language selection on page 288 • 26.2 boat details on page 289 • 26.3 units set-up on page 290 • 26.4 time and date set-up on page 291 • 26.5 display preferences on page 292 • 26.6 databar and databox customization on page 294 • 26.7 list ...
Page 288
26.1 language selection the system can operate in the following languages: english (us) english (uk) arabic bulgarian chinese croatian danish dutch finnish french german greek icelandic italian japanese korean norwegian polish portuguese (brazilian) russian spanish swedish turkish with the homescree...
Page 289
26.2 boat details you can customize various settings to make them specific to your vessel. Menu item description options boat type you can change the appearance of the vessel in the chart application. Select the option that most closely resembles the type and size of your vessel. Note: when boat typ...
Page 290
26.3 units set-up you can specify your preference for the units of measurement that will be used in all applications. Menu item description options distance units the units of measure that will be used in all applications for the display of all values related to distance. • nautical miles • statute ...
Page 291
26.4 time and date set-up you can specify your preference for the way that time and date will appear in all applications. Menu item description options date format allows you to specify the preferred format for the display of date information in all applications. • mm:dd:yy (month, day, year) • dd:m...
Page 292
26.5 display preferences you can specify your preference for general display behavior. Menu item description options starting page allows you to select what page the display opens at start up. • homescreen (default) • last page — after power up the last used page is displayed. • choose page — after ...
Page 293
Shared brightness you can set up shared brightness groups to adjust the brightness on multiple units simultaneously. The following units are compatible with shared brightness groups: • new a series • new c series. • new e series. • gs series • i50 • i60 • i70 • p70 / p70r pilot controllers • st70 • ...
Page 294
26.6 databar and databox customization you can customize the data displayed in onscreen databoxes and the databar. Customizable data is displayed in the databar, extended databar (hybridtouch displays only) or databoxes. The databar, extended databar and databoxes are available in all applications. ...
Page 295
26.7 list of data items depending on connected devices the categories of data available to display in the data application, data overlay, databar, and expanded databar are shown below. The following table shows the data items available by category. Data category description data item digital dials* ...
Page 296
Data category description data item digital dials* graphical* fuel flow rate fuel flow (inst) fuel flow (avg) engine hours engine trim alternator engine load fuel level (%) fuel level (vol) total fuel (%) total fuel (vol) fuel flow total economy estimated fuel remaining distance to empty time to emp...
Page 297
Data category description data item digital dials* graphical* water temperature minimum water temperature maximum water temperature vessel position cog & sog cog sog maximum sog gps gps-related data. For example, vessel position. Average sog heading heading and speed (data application only.) locked ...
Page 298
Data category description data item digital dials* graphical* distance to waypoint distance made good estimated time of arrival wpt ttg course to steer pilot pilot-related data. For example, rudder. Rudder angle speed maximum speed average speed speed and sog trolling speed vmg to windward speed spe...
Page 299
Data category description data item digital dials* graphical* maximum tws minimum tws twd twa & tws twa (ch) and tws twa and vmg awa & aws awa (ch) and aws awa and vmg awa and twa beaufort cardinal wind ground wind gwd & gws gwd and beaufort none note: *dials and graphical representations are only a...
Page 300
26.8 system set-up menus the system set-up menus enable you to configure your display and connected external devices. The following menus are available: menu item description notes touch-lock enables you to lock the touchscreen of a touch only display when the display is paired with a remote keypad....
Page 301
Alarms menu menu item description options mob data type determines whether position or dead reckoning (dr) data is displayed. Assuming that your vessel and the mob are subject to the same tide and wind effects, the dead reckoning setting normally gives a more accurate course. • dead reckoning • posi...
Page 302
Menu item description options • deep fish limit — specifies the upper value for the fish alarm depth limit. • 2 ft (or equivalent units) to the maximum of the transducer range deep fish limit • 2 ft (or equivalent units) to the maximum of the transducer range fuel manager in the fuel manager alarm o...
Page 303
Cartography set-up menu options the following table describes the various options in the cartography set-up menu for your multifunction display. Menu item description options chart display determines the level of detail shown on the chart. • simple • detailed (default) • extra detailed chart grid de...
Page 304
Menu item description options nav. Marks determines whether navigation marks are displayed on the chart: • off — navigation marks are not displayed. • on — navigation marks are displayed. • off • on (default) nav. Mark symbols determines which set of navigation mark symbols is used — international, ...
Page 305
Ground trip resets menu this menu enables you to resets the chosen ground trip distance counter to zero. Menu item description ground trip 1 reset resets the ground trip 1 distance counter to zero. Ground trip 2 reset resets the ground trip 2 distance counter to zero. Ground trip 3 reset resets the ...
Page 306
Multiple data sources (mds) overview installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of gps data. Mds enables you to manage conflicts involving the following types of data: • gps position. • heading....
Page 307
Data sources menu this menu enables you to select the external sensors and devices that will provide data to the display. Auto / manual selection each dialog enables you to view and select your preferred data source. Selection of data source can be manual or set to automatic: • auto — the display wi...
Page 308
External devices menu this menu enables you to configure the external devices connected to the display. Menu item description notes pilot set-up when connected to an evolution autopilot this option allows you to enable and disable pilot control and the pilot bar. You can also access certain pilot se...
Page 309
Connections menu this menu enables you to connect wireless bluetooth and wi-fi devices to the display. Menu item description options bluetooth enable or disable bluetooth on the display. • on • off (default) wi-fi enable or disable wi-fi on the display. • on • off (default) connection manager provid...
Page 310
Nmea set-up menu this menu enables you to configure settings for nmea devices. Menu item description options bridge nmea heading if set to on, nmea heading data will be bridged onto the seatalk data bus, and will be sent to all nmea-connected devices. If set to off, nmea heading data will not be bri...
Page 311
System preferences menu menu item description options bearing mode determines how all bearing and heading data is displayed in. This does not affect how the chart or radar displays are drawn. • true (default) • magnetic variation source this setting compensates for the naturally occurring offset of ...
Page 312
Maintenance menu this menu provides access to systems settings reset and diagnostics. Menu item description options touchscreen alignment if the touchscreen is misaligned to your touch, you can realign it to improve the accuracy. Realignment involves a simple exercise to align an on-screen object wi...
Page 313
Diagnostics menu if you encounter problems with your multifunction display or peripheral devices you can use the diagnostics menu to view information about your device and connected equipment. Select device enables you to a list of all devices connected to the seatalk hs network. You can also select...
Page 314
314 new a series / new c series / new e series.
Page 315
Chapter 27: maintaining your display chapter contents • 27.1 service and maintenance on page 316 • 27.2 cleaning on page 316 maintaining your display 315.
Page 316
27.1 service and maintenance this product contains no user serviceable components. Please refer all maintenance and repair to authorized raymarine dealers. Unauthorized repair may affect your warranty. Routine equipment checks raymarine strongly recommends that you complete a number of routine check...
Page 317
Chapter 28: troubleshooting chapter contents • 28.1 troubleshooting on page 318 • 28.2 power up troubleshooting on page 319 • 28.3 radar troubleshooting on page 320 • 28.4 gps troubleshooting on page 321 • 28.5 sonar troubleshooting on page 322 • 28.6 thermal camera troubleshooting on page 323 • 28....
Page 318
28.1 troubleshooting the troubleshooting information provides possible causes and corrective action required for common problems associated with marine electronics installations. All raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs...
Page 319
28.2 power up troubleshooting problems at power up and their possible causes and solutions are described here. Problem possible causes possible solutions check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion. The syst...
Page 320
28.3 radar troubleshooting problems with the radar and their possible causes and solutions are described here. Problem possible causes possible solutions check that the scanner power supply cable is sound and that all connections are tight and free from corrosion. Check relevant fuses and breakers. ...
Page 321
28.4 gps troubleshooting problems with the gps and their possible causes and solutions are described here. Problem possible causes possible solutions geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another ...
Page 322
28.5 sonar troubleshooting problems with the sonar and their possible causes and solutions are described here. Problem possible causes possible solutions unit power supply fault. Check the unit power supply and cables. Other unit fault. Refer to the instructions supplied with the unit. Check that th...
Page 323
28.6 thermal camera troubleshooting problems with the thermal camera and their possible causes and solutions are described here. Problem possible causes possible solutions camera is in standby mode. The camera will not display video if it is in standby mode. Use the camera controls (either the therm...
Page 324
28.7 system data troubleshooting aspects of the installation can cause problems with the data shared between connected equipment. Such problems, their possible causes and solutions are described here. Problem possible causes possible solutions check the data bus (e.G. Seatalk ng ) wiring and connect...
Page 325
28.8 video troubleshooting problems with the video inputs and their possible causes and solutions are described here. Problem possible causes possible solutions no signal message on screen (video image not displayed) cable or connection fault check that the connections are sound and free from corros...
Page 326
28.9 wi-fi troubleshooting aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem possible causes possible solutions ensure that wi-fi is enabled on the multifunction display (homesc...
Page 327
28.10 bluetooth troubleshooting aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem possible causes possible solutions ensure that bluetooth is enabled on the multifunction displa...
Page 328
28.11 touchscreen troubleshooting problems with the touchscreen and their possible causes and solutions are described here. Problem possible causes possible solutions touch lock is enabled. Use the joystick to turn off the touch lock on the home screen. Screen is not being operated with bare fingers...
Page 329
28.12 miscellaneous troubleshooting miscellaneous problems and their possible causes and solutions are described here. Problem possible causes possible solutions check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion. ...
Page 330
330 new a series / new c series / new e series.
Page 331
Chapter 29: technical support chapter contents • 29.1 raymarine customer support on page 332 • 29.2 third-party support on page 332 technical support 331.
Page 332
29.1 raymarine customer support raymarine provides a comprehensive customer support service. You can contact customer support through the raymarine website, telephone and e-mail. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Web support please ...
Page 333
Chapter 30: technical specification chapter contents • 30.1 technical specification on page 334 technical specification 333.
Page 334
30.1 technical specification a6x physical specifications dimensions • width: 163.57 mm (6.44 in) • height (not including bracket): 143.47 mm (5.65 in) • height (including bracket): 162.72 mm (6.41 in) • depth (not including cables): 74.1 mm • depth (including cables): 167.5 mm (6.6 in) weight (bare ...
Page 335
Power consumption full brightness: • a65 / a65 wi-fi — 8.6 w max • a67 / a67 wi-fi — 12.2 w max • a68 / a68 wi-fi — 10.6 w max powersave mode: • a65 / a65 wi-fi — 3.8 w max • a67 / a67 wi-fi — 7.4 w max • a68 / a68 wi-fi — 5.8 w max note: power consumption figures represent a loaded system and for s...
Page 336
Power consumption full brightness: • e165 — 59.5 w powersave mode: • e165 — 10.9 w note: power consumption figures represent a loaded system and for sonar variants include an active 600 w transducer. Len (refer to seatalk ng reference manual for further information). 1 environmental specification en...
Page 337
Update rate 1 second antenna ceramic chip accuracy • without sbas: 95% of the time • with sbas: the time internal sonar specification the internal sonar specifications only apply to sonar variant multifunction display variants. Operating frequencies 50 / 83 / 200 khz transmit power up to 600 w rms, ...
Page 338
338 new a series / new c series / new e series.
Page 339
Chapter 31: spares and accessories chapter contents • 31.1 transducer accessories on page 340 • 31.2 network cables on page 340 • 31.3 seatalk hs network cables on page 341 • 31.4 seatalk hs patch cables on page 341 • 31.5 video cables on page 342 • 31.6 a65 / a67 spares on page 342 • 31.7 e7 e7d sp...
Page 340
31.1 transducer accessories item part number notes p48 sonar transducer a102140 transom mount. P58 sonar transducer a102138 transom mount. 1 m (3.28 ft) minn kota transducer adaptor cable a62363 only for direct connection to sonar variant multifunction display. 0.5 m (1.64 ft) transducer adaptor cab...
Page 341
31.3 seatalk hs network cables cable part number 1.5 m (4.9 ft) seatalk hs network cable e55049 5 m (16.4 ft) seatalk hs network cable e55050 10 m (32.8 ft) seatalk hs network cable e55051 20 m (65.6 ft) seatalk hs network cable e55052 31.4 seatalk hs patch cables cable part number 1.5 m (4.9 ft) se...
Page 342
31.5 video cables the following video cable is required for the video in / out connector on the e95 / e97 / e125 / e127 variant multifunction displays. Part number description notes r70003 e-series accessory video cable 31.6 a65 / a67 spares item part number notes trunnion (bracket) mount kit r70147...
Page 343
31.7 e7 e7d spares item part number notes trunnion (bracket) mount kit a62358 documentation pack r62378 flush mount panel set r62376 front bezel r62377 suncover r62365 1.5 m (4.9 ft) straight power and data cable r62379 1.5 m (4.9 ft) right angled power and data cable r70029 31.8 e95 / e97 / c95 / c...
Page 344
31.9 e125 / e127 / c125 / c127 spares item part number notes c/e series trunnion kit r70002 c/e series front bezel r7006 c/e series suncover r70007 c/e/ series rear bezel r70028 c.E series gasket r70080 mounting adaptor kit — c120w/e120w r70009 mounting adaptor kit — c120/e120 r70011 mounting screw ...
Page 345
Appendix a nmea 0183 sentences the display supports the following nmea 0183 sentences. These are applicable to nmea 0183 and seatalk protocols. Sentence description transmit receive aam waypoint arrival alarm sentence ● apb autopilot sentence ‘b’ ● ● bwc bearing and distance to waypoint ● ● bwr bear...
Page 346
Appendix b nmea 2000 sentences the display supports the following nmea 2000 sentences. These are applicable to nmea 2000, seatalk ng and seatalk 2 protocols. Message number message description transmit receive bridge 59392 iso acknowledgment ● ● ● 59904 iso request ● ● 60928 iso address claim ● ● ● ...
Page 347
Message number message description transmit receive bridge 129793 ais utc and date report ● 129794 ais class a static and voyage related data ● 129798 ais sar aircraft position report ● 129801 ais addressed safety related message ● 129802 ais safety related broadcast message ● 129809 ais class b “cs...
Page 348
Appendix c connectors and pinouts power, data, and video connector d12186-1 1 8 4 9 2 7 3 6 5 11 10 item remarks identification pwr / nmea / video connector type 11 pin twist-lock current source to network no current sourced for external devices current sink from network • psu: main power input. • n...
Page 349
Pin signal 13 video in2 rtn 14 red rtn 15 red appendix d switch panel application vessel control and monitoring systems when integrated with a vessel control and monitoring system your multifunction display can provide monitoring and controls for your power circuits, breakers, switches and equipment...
Page 350
3. Insert the memory card into the card reader on your multifunction display. 4. From the homescreen select set-up. 5. Select system settings. 6. Select external devices. 7. Select switch panel set-up. 8. Select install config file. 9. If prompted select the memory card slot that contains your confi...
Page 351
Appendix e software releases raymarine regularly updates its multifunction display software to introduce improvements, additional hardware support and user interface features. The table below details some of the important enhancements and which software revision they were introduced with. Software v...
Page 352
Software version applicable product manual multifunction displays compatibility changes • ability to record live bus messages (nmea 0183 and seatalk ng to sd card. V4.32 81337–4 c95 / c97 / c125 / c127 / e7 / e7d / e95 / e97 / e125 / e127 • addition of on-screen range controls to the chart & radar a...
Page 354
Www.Ra ym a rin e .C o m.