- DL manuals
- Raymarine
- Keypad
- RMK-10
- Installation Instructions Manual
Raymarine RMK-10 Installation Instructions Manual
Summary of RMK-10
Page 1
© 2016 raymarine uk limited 81367-1 document number: 11-2016 date: english (en-us) installation instructions rmk-10
Page 2
Trademark and patents notice raymarine, tacktick, clear pulse, truzoom, hsb, seatalk, seatalk hs , seatalk ng , micronet, raytech, gear up, marine shield, seahawk, autohelm, automagic, and visionality are registered or claimed trademarks of raymarine belgium. Flir, downvision, sidevision, dragonfly,...
Page 3: Water Ingress
Chapter 1: important information warning: product installation and operation • this product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance. • raymarine recommends cer...
Page 4: Declaration
Note: where constraints on the installation prevent any of the above recommendations, always ensure the maximum possible separation between different items of electrical equipment, to provide the best conditions for emc performance throughout the installation declaration of conformity raymarine uk l...
Page 5: 2.1 Document Information
2.1 document information this document contains important information related to the installation of your raymarine product. The document includes information to help you: • plan your installation and ensure you have all the necessary equipment; • install and connect your product as part of a wider ...
Page 6: 3.1 Installation Checklist
3.1 installation checklist installation includes the following activities: installation task 1 plan your system. 2 obtain all required equipment and tools. 3 site all equipment. 4 route all cables. 5 drill cable and mounting holes. 6 make all connections into equipment. 7 secure all equipment in pla...
Page 7: 3.3 Software Updates
3.3 software updates the software running on the product can be updated. • raymarine periodically releases software updates to improve product performance and add new features. • the software on many products can be updated using a connected and compatible multifunction display (mfd). Important: • t...
Page 8: 3.6 Warnings And Cautions
3.5 general location requirements important considerations when choosing a suitable location for your product. This product is suitable for mounting above or below decks. The product should be mounted where it will be: • protected from physical damage and excessive vibration. • well ventilated and a...
Page 9: Chapter
4.1 general cabling guidance cable types and length it is important to use cables of the appropriate type and length • unless otherwise stated use only standard cables of the correct type, supplied by raymarine. • ensure that any non-raymarine cables are of the correct quality and gauge. For example...
Page 10: 4.2 Connections Overview
4.2 connections overview 1. Alternate power connector 2. Network / poe connector the alternate power connector is required when connecting to a network which does not support power over ethernet poe. The alternate power connector must be connected directly to a power supply. Note: do not connect the...
Page 11: 4.4 Keypad Connections
4.4 keypad connections the keypad can be connected directly to a multifunction display’s (mfds) network connector or via a network switch. Multiple keypads can be connected to a system. Each keypad can be used to control multiple mfds. If the network is not providing power over ethernet (poe) then t...
Page 12
3. Right angled power cable (connected to the alternate power connector.) 4. Networked mfds note: once connected the keypad must be paired with each mfd you want to control with the keypad. Cables and connections 19.
Page 13: Chapter
5.1 removing the keypad mat to gain access to the mounting hole locations, the keypad mat must be removed. Tip to help prevent scratching the product, cover the tip of your screwdriver blade with a small piece of insulation tape. 1. Using a thin, flat bladed screwdriver insert the tip of the screwdr...
Page 14
5.3 surface mounting the keypad surface mounting provides a uniform installation where the products protrude, usually by the thickness of the bezel, from the mounting surface. 1. Check the selected location for the unit. A clear, flat area with suitable clearance behind the panel is required. 2. Bef...
Page 15: Chapter
1. Home — press to return to the homescreen. 2. Menu — accesses menus. Press again to close menus. 3. Unicontroller — provides a rotary control and a joystick that includes an ok push button for using menus and applications. 4. Back — press to return to a previous menu or dialog level. 5. - (minus/n...
Page 16: 6.2 Pairing The Keypad
6.2 pairing the keypad each keypad can be paired with multiple mfds and multiple keypads can be connected to the same system. With the keypad connected to the mfd: 1. Select external keypad from the external devices menu: homescreen > set-up > system settings > external devices > external keypad. 2....
Page 17: 7.1 Keypad Status
7.1 keypad status the keypad is backlit with leds. The leds are used to identify the status of the keypad. Status unicontroller led ring keypad backlight keypad powered off or not paired off off keypad is powered on and paired on on mfd is in powersave mode flashing off the led and keypad backlight ...
Page 18
7.3 power up troubleshooting problems at power up and their possible causes and solutions are described here. Product does not turn on or keeps turning off possible causes possible solutions blown fuse / tripped breaker 1. Check condition of relevant fuses and breakers and connections, replace if ne...
Page 19: Chapter
8.1 service and maintenance this product contains no user serviceable components. Please refer all maintenance and repair to authorized raymarine dealers. Unauthorized repair may affect your warranty. 8.2 routine equipment checks raymarine strongly recommends that you complete a number of routine ch...
Page 20: 9.2 Compliance
9.1 technical specification power specification poe class class 1 nominal supply voltage • poe: 48 v dc • alternate power: 12 v / 24 v dc operating voltage range • poe: 44 v to 57 v dc • alternate power: 9 v to 32 v dc power consumption 4 w max with full keypad illumination environmental specificati...
Page 21: And Servicing
10.1 raymarine product support and servicing raymarine provides a comprehensive product support service, as well as warranty, service, and repairs. You can access these services through the raymarine website, telephone, and e-mail. Product information if you need to request service or support, pleas...
Page 22: 10.2
10.2 learning resources raymarine has produced a range of learning resources to help you get the most out of your products. Training courses raymarine regularly runs a range of in-depth training courses to help you make the most of your products. Faqs and knowledge base raymarine has produced an ext...
Page 23: Chapter
11.1 keypad spares and accessories spares item part number portrait keypad mat spare r70509 landscape keypad mat spare r70508 accessories item part number right angled 2 m (6.6 ft) power cable a06070 straight 2 m (6.6 ft) power cable a06049 44 chapter 11: spares and accessories.
Page 24
Raynet to raynet cables and connectors description typical use quantity 1 standard raynet connection cable with a raynet (female) socket on both ends. Suitable for connecting all raynet equipment directly to lighthouse multifunction displays featuring a raynet connector. Can also be used to connect ...
Page 25
Raynet to rj45 adapter cables description typical use quantity 1 adapter cable with a raynet (female) socket on one end, and a waterproof (female) socket on the other end accepting the following cables with an rj45 seatalk hs waterproof locking (male) plug: • a62245 (1.5 m). • a62246 (15 m). A typic...