- DL manuals
- Raymarine
- Marine GPS System
- RS130 GPS
- Installation Instructions Manual
Raymarine RS130 GPS Installation Instructions Manual
Summary of RS130 GPS
Page 1
R s 1 3 0 g p s ins ta lla tion ins tructions en g lis h da te : 02-2012 docume nt numbe r: 87134-3 © 2012 ra yma rine uk limite d rs130 gps receiver – installation instructions.
Page 3
Trademark and patents notice autohelm, hsb 2 , raytech navigator, sail pilot, seatalk, seatalk ng , seatalk hs and sportpilot are registered trademarks of raymarine uk limited. Raytalk, seahawk, smartpilot, pathfinder and raymarine are registered trademarks of raymarine holdings limited. Flir is a r...
Page 5: Contents
Contents chapter 1 introduction ............................................. 7 handbook information ..................................................... 7 safety notices................................................................. 7 important information ..........................................
Page 6
6 rs130 gps receiver – installation instructions.
Page 7: Chapter 1: Introduction
Chapter 1: introduction handbook information this handbook describes how to install the raymarine rs130 gps receiver as part of a marine electronics installation. This handbook includes information to help you: • plan your installation and ensure you have all the necessary equipment; • install and c...
Page 8
It is important that you register your product to receive full warranty benefits. Your unit package includes a bar code label indicating the serial number of the unit. You will need this serial number when registering your product online. You should retain the label for future reference. 8 rs130 gps...
Page 9
Chapter 2: planning the installation chapter contents • 2.1 installation checklist on page 10 • 2.2 seatalk ng gps systems — examples on page 10 • 2.3 seatalk ng on page 11 • 2.4 parts and accessories on page 12 planning the installation 9.
Page 10: 2.1 Installation Checklist
2.1 installation checklist installation includes the following activities: installation task 1 plan your system 2 obtain all required equipment and tools 3 site all equipment 4 route all cables. 5 drill cable and mounting holes. 6 make all connections into equipment. 7 secure all equipment in place....
Page 11: 2.3 Seatalk
Example: extended gps system featuring a g-series processor unit smartpilot d12018-2 seatalk ng 3 2 4 5 6 n mea 0183 1 1. Seatalk ng g-series gpm processor unit. 2. Nmea 0183 dsc vhf radio. 3. Seatalk ng spx course computer. 4. Seatalk ng instrument. 5. Seatalk ng instrument. 6. Seatalk ng gps recei...
Page 12: 2.4 Parts And Accessories
2.4 parts and accessories parts supplied d 12020-2 1 2 4 6 3 5 1. Gps receiver. 2. Pole mount kit. 3. Seatalk ng spur cable (6 meters). 4. Screw pack, consisting of: • studs (quantity: 2) • thumb nuts (quantity: 2) • screws (quantity: 2) 5. Flush mount gasket. 6. Mounting template. Optional accessor...
Page 13
Chapter 3: cables and connections chapter contents • 3.1 general cabling guidance on page 14 • 3.2 seatalk ng connection overview on page 14 • 3.3 seatalk ng connection overview — long cable runs on page 15 • 3.4 nmea 2000 connection overview on page 15 • 3.5 seatalk ng cabling components on page 16...
Page 14: 3.2 Seatalk
3.1 general cabling guidance cable types and length it is important to use cables of the appropriate type and length • unless otherwise stated use only standard cables of the correct type, supplied by raymarine. • ensure that any non-raymarine cables are of the correct quality and gauge. For example...
Page 15: 3.3 Seatalk
3.3 seatalk ng connection overview — long cable runs use the optional seatalk ng inline terminator to connect the gps receiver’s spur cable directly to the extreme end of the seatalk ng backbone using the inline terminator. This removes the need for a t-piece connector and a separate terminator, mak...
Page 16: 3.5 Seatalk
3.5 seatalk ng cabling components seatalk ng cabling components and their purposes. Connection / cable notes backbone cable (various lengths) the main cable carrying data. Spurs from the backbone are used to connect seatalk ng devices. T-piece connector used to make junctions in the backbone to whic...
Page 17: 3.7 Power Connection
Description part no notes devicenet adaptor cable (male) a06046 allows the connection of nmea 2000 devices to a seatalk ng system. Devicenet adaptor cable (female) to bare ends. E05026 allows the connection of nmea 2000 devices to a seatalk ng system. Devicenet adaptor cable (male) to bare ends. E52...
Page 18
18 rs130 gps receiver – installation instructions.
Page 19: Chapter 4: Installation
Chapter 4: installation chapter contents • 4.1 location requirements on page 20 • 4.2 pole mounting the gps receiver on page 20 • 4.3 flush mounting the gps receiver on page 21 • 4.4 gps receiver seatalkng connection on page 21 • 4.5 checking gps operation on page 22 installation 19.
Page 20: 4.1 Location Requirements
4.1 location requirements when planning the installation location, consider the following: • the gps receiver is waterproof, and appropriate for above decks mounting. • choose a location that provides the most unobstructed view of the sky in all directions: d 12046-2 • do not mount the gps receiver ...
Page 21
4.3 flush mounting the gps receiver 5 3 4 7 d12047-2 1. Use the supplied mounting template to mark the 2 fixing holes and the center hole. 2. Drill the holes using the drill sizes shown on the supplied template. 3. Screw the 2 fixing studs into the underside of the receiver unit. 4. Place the waterp...
Page 22
4.5 checking gps operation you can check that the gps is functioning correctly using the chart application. 1. Select the chart page. 2. Check the screen. With the chart displayed, you should see: your boat position (indicates a gps fix). Your current position is represented by a boat symbol or soli...
Page 23
Chapter 5: troubleshooting and support chapter contents • 5.1 gps receiver led indications on page 24 • 5.2 gps troubleshooting on page 25 • 5.3 raymarine customer support on page 26 troubleshooting and support 23.
Page 24
5.1 gps receiver led indications the led on the gps receiver indicates status information for diagnostic purposes. Led activity (based on 1000 ms (1 second) cycle) led state description status description off red orange green 1000 ms 0 ms 0 ms 0 ms off no power. 900 ms 100 ms 0 ms 0 ms short flash r...
Page 25: 5.2 Gps Troubleshooting
5.2 gps troubleshooting problems with the gps and their possible causes and solutions are described here. Problem possible causes possible solutions geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another g...
Page 26
5.3 raymarine customer support raymarine provides a comprehensive customer support service. You can contact customer support through the raymarine website, telephone and email. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Web support please vi...
Page 27
Appendix a technical specification nominal supply voltage 12 or 24 v dc note: seatalk ng must be connected to 12 v systems only. 24 v support is provided for compatibility with future system configurations. Operating voltage range -10% to +30% of nominal supply range power consumption 50 ma max. Env...
Page 28
Www.Ra ym a rin e .C o m.