St60 graphic display commissioning guide document number: 81228-1 date: 1 january 2004 81228_1.Book page 1 wednesday, november 19, 2003 10:29 am.
Raymarine, st60 and seatalk are trademarks of raymarine limited © handbook contents copyright raymarine limited 2004 81228_1.Book page 2 wednesday, november 19, 2003 10:29 am.
I important information about the documentation welcome to the raymarine st60 graphic display. The documentation for your st60 graphic display is arranged so that you can install, commission and quickly use your display, keeping to hand only the information necessary. • installation guide - one easy...
Ii st60 graphic display commissioning guide caution: setup requirement the st60 graphic display is calibrated to factory (default) settings when first supplied. To ensure optimum performance on your boat, this product must be setup before use. Do not use the product until it has been setup using the...
Iii • if a suppression ferrite is attached to a cable, this ferrite should not be removed. If the ferrite needs to be removed during installation it must be reassembled in the same position. Suppression ferrites the following illustration shows typical cable suppression ferrites used with raymarine ...
Iv st60 graphic display commissioning guide 81228_1.Book page iv wednesday, november 19, 2003 10:29 am.
V contents important information ..........................................................................................I about the documentation .......................................................................... I safety notices ..............................................................
Vi st60 graphic display commissioning guide 81228_1.Book page vi wednesday, november 19, 2003 10:29 am.
1 chapter 1: system connections 1.1 overview this chapter assumes the st60 graphic display has been fitted in accordance with the instructions in the st60 graphic display installation guide . Mandatory connections the st60 graphic display receives both data and power from seatalk. You must therefore...
2 st60 graphic display commissioning guide receive a satisfactory power supply. The requirements for power connections are detailed in the following table. : connection procedure to connect your st60 graphic display: 1. Ensure that: • power to the existing seatalk system is switched off. • the condi...
Chapter 1: system connections 3 1.3 using the nmea in and out connectors although the nmea connectors provide a useful means of interfacing with external systems, you do not have to connect to nmea if you are receiving the data you want from seatalk. Caution: connections to other equipment if you ar...
4 st60 graphic display commissioning guide what nmea data is supported? Seatalk to nmea 0183 data from seatalk is transmitted to the nmea out connector every 2 seconds. The supported nmea output data is detailed in the following table. Nmea to seatalk when certain nmea data is available at the nmea ...
Chapter 1: system connections 5 alternative uses of nmea out connector the nmea out connector can be used in either of the following ways: • to output supported nmea data to an external nmea system. • to connect alarm signals to an auxiliary alarm. Note: if you connect the nmea out connector to an a...
6 st60 graphic display commissioning guide 81228_1.Book page 6 wednesday, november 19, 2003 10:29 am.
7 chapter 2: preparation for use 2.1 introduction use this chapter to set up and check the st60 graphic display, before it is used operationally. Instructions are given to enable you to: • define the function of the nmea out connector (see chapter 1, system connections ). • carry out dealer calibrat...
8 st60 graphic display commissioning guide 5. When you have set nmea out and alarm drive as required, hold down the and buttons for approximately 2 seconds to return to normal operation. Other user calibration functions comprehensive user calibration instructions are given in the st60 graphic displa...
Chapter 2: preparation for use 9 • set the instrument time to local time. • select the units in which temperature, speed, trip, depth and wind speed from nmea, are displayed. • select the function of the display nmea out connector. This is either • a remote alarm output for the auxiliary alarm (nmea...
10 st60 graphic display commissioning guide user calibration on/off press the track or reset button to toggle the user calibration either on or off as required. Note: if at any time, you want to access the software version and serial num- ber, you need to set user calibration on . Response settings ...
Chapter 2: preparation for use 11 you can set responses for the following data: • speed ( speed resp. ) • depth ( depth resp. ) • heading ( heading resp. ) • wind angle ( wind angle r. ) • wind speed ( wind speed r. ) • cross track error ( xte resp. ) battery voltage use the battery screen to set th...
12 st60 graphic display commissioning guide self test self test is intended for engineers engaged in diagnostic procedures. Always set this to no . Note: if yes is selected, you could inadvertently initiate a self test routine. This will not harm the product but will interrupt operation, so it is th...
Chapter 2: preparation for use 13 leaving dealer calibration hold down the and buttons for 2 seconds to save your settings and exit dealer calibration. 2.3 checking operation when installation and initial set up are complete, check that the st60 graphic display performs satisfactorily by carrying ou...
14 st60 graphic display commissioning guide 81228_1.Book page 14 wednesday, november 19, 2003 10:29 am.
Index 15 index a auxiliary alarm connections 5 c checking operation 13 connections auxiliary alarm 5 mandatory 1 nmea 3 optional 1 procedure 2 seatalk 1 d dealer calibration default reset 11 enable/disable user cal 10 setting responses 10 setting voltage reading 11 default settings 11 e emc conforma...
16 index 81228_1.Book page 16 wednesday, november 19, 2003 10:29 am.
