1. DL manuals
  2. Raynor
  3. Garage Door Opener
  4. MH5011ULCHB
  5. User Manual

Raynor MH5011ULCHB User Manual - Basic Programming

Other manuals for MH5011ULCHB: Installation Manual
Manual is about: Medium Duty Door Operator

Summary of MH5011ULCHB

  • Page 1

    Radio receiver built on board 315 mhz installation date contact information medium duty logic user's guide mh5011urchb mh5011ulchb mt5011uchb mj5011uchb www.Raynor.Com.

  • Page 2: Introduction

    2 introduction determine the wiring type the functionality of this operator is based on the wiring type. The operator is shipped from the factory in standard c2 wiring type (factory default). Liftmaster monitored entrapment protection (lmep) device is required. Notes: • the led on the logic board wi...

  • Page 3: Basic Programming

    3 photoelectric sensor alternate installation: c2 wiring type with monitored entrapment protection device • momentary contact to open and stop with constant pressure to close. • open override that reverses when closing by any opening device. • wiring for entrapment protection device to reverse. Note...

  • Page 4: Basic Programming

    4 to prevent possible severe injury or death: • install a liftmaster monitored entrapment protection (lmep) device. • never permit children to operate or play with door control push buttons or remote controls. • activate door only when it can be seen clearly, is properly adjusted and there are no ob...

  • Page 5: Basic Programming

    5 d14 com intrlk stop led open close ttc learn 1 lmep1 lmep2 23 4 5 6 7 st op close open r27 aux ant ^^^^ aux ant aux ant d14 com intrlk stop led open close ttc learn 1 lmep1 lmep2 23 4 5 6 7 st op close open press and release the learn button (led will light). Basic programming timer defeat the ttc...

  • Page 6: Testing

    6 requires b2 wiring type and compatible liftmaster remote control. In c2 wiring the remote control will open the door only. Press remote control button. Door should open. Allow the door to fully open. Press remote control button. Door should close. Allow door to fully close. Testing turn on power, ...

  • Page 7: Emergency Disconnect

    7 the operators have provisions for manually operating the door in case of emergency or power failure. Refer to the appropriate instructions for your model operator. Model mt/bmt emergency disconnect no e c i t emergency disconnect door emergency release handle emergency disconnect door arm pull eme...

  • Page 8: Emergency Disconnect

    8 emergency disconnect model mh these operators are equipped with a manual hoist. An electrical interlock will disable the electrical controls when the hoist is used. Pull the disconnect chain (sash chain) to engage the hoist mechanism. The disconnect chain may be locked in position by slipping the ...

  • Page 9: Troubleshooting

    9 troubleshooting maintenance schedule to avoid serious personal injury or death from electrocution, disconnect all electric power before performing any maintenance. Attention avertissement avertissement avertissement warning caution warning warning warning precauciÓn advertencia advertencia adverte...

  • Page 10: Operator Notes

    10 operator notes.

  • Page 11: Accessories

    11 m m o o d d e e l l m m t t 5 5 0 0 1 1 1 1 u u / / b b m m t t 5 5 0 0 1 1 1 1 u u quick start aglkdngdna diakdn alkndjandjan adlknsa;fkn;d agndan;djksna;dkjn dgajndsandoai langdlaknskdnoa lknagdndjoang; gksdjna;ogdnr aglkna;gn;djkand adgsndajgndoia lajgdajngciosuhadoajdna ld dagjdl;abndjnbag;du...

  • Page 12: Accessories

    © 2010, the chamberlain group, inc. All rights reserved accessories field modification kits 71mlsbc single button control: provides additional input for single button control functionality. Input functions as close input when the operator is stopped at the open limit. Input functions as open input a...