Rion gh40 greenhouse assembly instructions modular greenhouses, garden sheds, outdoor garden elements and accessories designed and manufactured by rion a member of the plasson group international headquarters north american distributor rion ltd. Cabri 25120 o israel tel: +972-4-995-2666, fax: +972-4...
© 2006 rion ltd..
1 safety first • check the contents of the greenhouse packaging against the packing list and the required parts for your model on page 4 and following. Do not begin assembly if any parts are missing. • please read these assembly instructions completely before assembly and keep them in your records s...
2 gh40 greenhouse assembly instructions introduction congratulations on purchasing a rion greenhouse. We are certain that it will give you many happy years of pleasure in your garden. The drawings in this manual are designed for the greenhouse owner who has purchased a gh44, which consists of one fr...
3 prepare a foundation for your greenhouse before assembling your new greenhouse a proper foundation must be prepared. A number of anchoring options are possible, based on wind and ground conditions in your area. Make sure that you have checked with your local authorities regarding any required buil...
4 gh40 greenhouse assembly instructions identify greenhouse parts because of the greenhouse modularity, you may purchase additional gh40m modules to fit your needs..
5 take a minute to make sure you have everything you need. Note: do not proceed with assembly if any parts are missing. The part code is stamped on each connector. Profiles are listed in order by size, largest to smallest. Panels are identified with stickers. Exact dimensions can be found in the pac...
6 gh40 greenhouse assembly instructions as80 4 4 4 door runner screw / wingnut door33 1 1 1 door handle r1 4 4 4 round profile (113 cm, 3' 8 a ") r8 4 4 4 round profile (80.2 cm, 2' 7 l ") r2 4 4 4 round profile (53.4 cm, 1' 9") e12 1 1 1 oval profile (116.2 cm, 3' 9 c ") e1 15 19 23 oval profile (1...
7 prepare your parts for assembly remove everything from your packages and sort them according to part type. Since assembly is done from taking parts from every box, it is best to put everything together. The boxes are printed with a ruler to help you distinguish between profiles. Note: protect unas...
8 gh40 greenhouse assembly instructions lay out the greenhouse frame decide in which direction the door will face and place the parts on the prepared foundation or wood deck. Note: if you are using a modular base or other foundation option (see page 3) assemble the base on a flat surface (such as a ...
9 secure the frame to the foundation make sure you have the proper hardware before beginning this step. (see page 3.) note: if you are using a modular base and filler you may assemble the greenhouse on a hard surface and move it to its final position when you have finished. Make sure that there are ...
10 gh40 greenhouse assembly instructions assemble the roof pediments put st7 couplers on the pn8r and pn8l pediment panel halves as shown. The tops of each coupler are trimmed to match the angle of the panel. Note: the outside surface of the panels have special uv protection, indicated by the logo a...
11 back pediment put st7 couplers on the pn8r and pn8l pediment panel halves with the id plastic strip facing outside. The tops of each coupler are trimmed to match the angle of the panel. Slide the two pediment panel halves together. Assemble all parts of the back pediment except for the 7a connect...
12 gh40 greenhouse assembly instructions assemble roof framework note: assemble the roof in an area not too far away from the completed base. First assemble the first arch. Slip one end of the cab40 cable through the 6 mm (¼") channel on the underneath side of the 5a connector. You may use the gt1 p...
13 cover the greenhouse roof step in the framework of the lower window to reach the top of the roof conveniently. Place ra1 glazing elements on the top of the roof by placing one end in the top channel and pushing it down along the length of the profile. Place rb1, rb4, and rb6 glazing elements alon...
14 gh40 greenhouse assembly instructions place rd1 elements where shown by placing one end in the channel and pushing it down along the length of the profile. Note: you may find it easier to insert rd elements into profiles by pushing them in from the top while rolling the element downwards. Note: b...
