RIPSpeed DV720 Owner's Manual - page 7
TFT Monitor Operation
Operating Instructions
Open/Close the TFT Monitor
Press the ( ) button on the front panel or the (OPEN) button on the remote control to open/close
the monitor.
TFT Monitor Auto Open
If “TFT Auto Open” is “On”, when the unit is turned on, the monitor automatically opens to the last
viewing position, and closes automatically when the unit is turned off.
If “TFT Auto Open” is “Off”, when the unit is turned on, the monitor will not open automatically, but will
close automatically when the unit is turned off. You can press the ( ) button on the front panel or
the (OPEN) button on the remote control to move the monitor into the desired viewing position.
If “TFT Auto Open” is “Manual”, when the unit is turned on or turned off, the monitor has no
movement.
See “General setting” for details.
Monitor Tilt Angle Adjustment
The monitor angle can be adjusted for optimum viewing using one of the following methods:
Press the ( ) or ( ) buttons on the front panel to adjust the tilt angle of the screen one step at a
time.
Press and hold the ( ) or ( ) buttons to continuously adjust the tilt angle. Adjust the “Screen Tilt”
in the “Screen setting” to adjust the tilt of the screen to the desired degree.
Image Setting
Video Output Format
The table below shows the video output format for each source.
Adjustable Parameters
While on RGB mode, the only parameter that can be adjusted is brightness (BRIGHT). To
access“SHARPNESS” “COLOR” “CONTRAST” “BRIGHTNESS” and “TINT ”you must be on CVBS
mode.
Parameter Adjustment Procedure
1. Enter Picture Quality Setting Mode:
Press the PIC button on the remote or press and hold the INFO button on the front panel of the unit.
2. Select Items to Set:
Press the ( / ) buttons on the remote or rotate the SMART DIAL button clockwise/anticlockwise
to select an item.
3. Set Parameters:
Press the ( / ) buttons on the remote or press the ANGLE button ( / ) on the front panel to
adjust the selected feature to the desired setting. Rotate the“ VOL” on the front panel can also adjust
the selected feature.
4. Exit Picture Quality Setting Mode:
Press the PIC button on the remote or press and hold the INFO button on the unit.
Parking Brake Interlock
1. When the “PARKING” lead is properly connected to the brake switch, the display on the TFT
monitor will display video only when the vehicle is stopped and the parking brake is applied.
2. When the “parking brake interlock” is active, the front monitor displays a caution messsage with a
blue background, preventing the driver from watching video while driving to reduce the risk of a traffic
accident. Please see “INSTALLATION SECTION” for installation.
Monitor Movement Mechanism
If an obstruction occurs on the monitor path, the motion will stop automatically to prevent damage for
the mechanism or monitor.
Normal operation is resumed by pressing the ( ) button or disconnecting and reconnecting the
Power.
Power On / Off
Press the POWER/VOL button to turn the unit on. The buttons on the front of the unit are illuminated
and start up message is briefly displayed on the LCD screen, and then displays the current mode
status. You can also turn on the unit by pressing the ( ) button on the remote control.
Press and hold the POWER/VOL button on the front panel for more than 1 second or press the ( )
button on the remote to power off the unit. The monitor is drawn back into the main compartment and
the LCD screen displays “BYE BYE”.
NOTE:
The operating voltage range is 10.5v~16v. The unit will power off automatically to protect
itself, when the voltage is out of the operating range.
Playing Source Selection
Press the MODE button on the front panel or the (MODE) button on the remote to select among the
available sources: TUNER, Disc, AUX IN. The selected playing mode is displayed on the TFT or LCD
screen.
AUX IN Mode
An external peripheral device can be connected to this unit via RCA cables to the “AUX-IN”.
Volume Adjustment
To increase or decrease the volume level, turn the POWER/VOL on the front panel or press the
(VOL+/ VOL-) buttons on the remote control. The volume ranges from “0” to “40”. The default volume
is “10” when the unit is powered on each time. Default volume memory setup: Rotate Power/VOL
knob on the front panel to select volume value and then press and hold the Power/VOL button until
you hear a single beep. When you hear the beep, setup is completed.
Audio Control Menu
The Audio Control feature allows you to easily adjust your audio system to meet the acoustical
characteristics of your vehicle, which vary depending on the type of vehicle and its measurements.
To get the best possible sound quality from your new system, be sure to adjust the settings for the
speakers as well. Proper setting of the Fader and Balance enhances the effects of the cabin
equalizer.
Accessing the Audio Control Menu
Press the POWER/VOL on the front panel once or press the (SEL) button on the remote control to
enter the “Audio” menu.
Selecting an Audio Feature for Adjustment
Press the ( / ) buttons on the remote to select a item to be adjusted.
Rotate the “Smart Dial ”on the front panel to select a item to be adjusted.
Adjusting an Audio Feature
Press the ( / ) buttons on the remote or rotate the POWER/VOL clockwise/counterclockwise to
adjust the selected feature to the desired setting.
8
7