1. DL manuals
  2. Riverstone Networks
  3. Network Router
  4. RS 3000
  5. Getting Started Manual

Riverstone Networks RS 3000 Getting Started Manual

Other manuals for RS 3000: Getting Started Manual
Manual is about: Switch Router

Summary of RS 3000

  • Page 1

    36-004-16 rev. 0 b rs 3000/3100/3200 switch router getting started guide release 9.4.0.1.

  • Page 2

    Ii riverstone networks rs 3000/3100/3200 switch router getting started guide copyright notices © 2003 by riverstone networks, inc. All rights reserved. Riverstone networks, inc. 5200 great america parkway santa clara, ca 95054 printed in the united states of america this product includes software de...

  • Page 3

    Riverstone networks rs 3000/3100/3200 switch router getting started guide iii regulatory compliance information this product complies with the following: safety ul 1950; csa c22.2, no. 950; 73/23/eec; en 60950; iec 950 electromagnetic fcc part 15, canada ices-003, en 55022, vcci and en 55024 compati...

  • Page 4

    Iv riverstone networks rs 3000/3100/3200 switch router getting started guide warning changes or modifications made to this device that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Industry canada compliance statement thi...

  • Page 5

    Riverstone networks rs 3000/3100/3200 switch router getting started guide v vcci compliance statement this is a class a product based on the standard of the voluntary control council for interference by information technology equipment (vcci). If this equipment is used in a domestic environment, rad...

  • Page 6

    Vi riverstone networks rs 3000/3100/3200 switch router getting started guide fábrica y no puede ser ajustada por el usuario. Los transmisores/receptores láser de clase 1 cumplen con las siguientes normas de seguridad: • 21 cfr 1040.10 y 1040.11, departamento de salud y servicios humanos de los estad...

  • Page 7

    Riverstone networks rs 3000/3100/3200 switch router getting started guide vii safety information: wict1-12 t1 card warning to reduce the risk of fire, use only no. 26 awg or larger telecommunication line cord. Warning para reducir el riesgo de un incendio, únicamente utilice un conductor del número ...

  • Page 8

    Viii riverstone networks rs 3000/3100/3200 switch router getting started guide before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of co...

  • Page 9

    Riverstone networks rs 3000/3100/3200 switch router getting started guide ix riverstone networks, inc. Standard software license agreement important: before utilizing the product, carefully read this license agreement. This document is a legal agreement ("agreement") between you, the end user, and r...

  • Page 10

    X riverstone networks rs 3000/3100/3200 switch router getting started guide 5. Maintenance and updates. Updates, upgrades, bug fixes, and maintenance and support services, if any, are provided to you pursuant to the terms of a riverstone service and maintenance agreement, and only if riverstone and ...

  • Page 11

    Riverstone networks rs 3000/3100/3200 switch router getting started guide xi riverstone standard warranty a. Product warranty i. Riverstone warrants that each unit of hardware products will be free from defects in material and work- manship for a period of one (1) year from the date of shipment. Ii....

  • Page 12

    Xii riverstone networks rs 3000/3100/3200 switch router getting started guide in effect. V. Riverstone shall have full and free access to the products and licensed materials at purchaser's cus- tomer's site, if required. Vi. Riverstone shall not be responsible for failure to furnish parts due to cau...

  • Page 13

    Riverstone networks rs 3000/3100/3200 switch router getting started guide xiii declaration of conformity addendum application of council directive(s) 89/336/eec 73/23/eec manufacturer’s name riverstone networks, inc. Manufacturer’s address 5200 great america parkway santa clara, ca 95054 conformance...

  • Page 14

    Xiv riverstone networks rs 3000/3100/3200 switch router getting started guide.

  • Page 15

    Riverstone networks rs 3000/3100/3200 switch router getting started guide xv table of contents 1 about this guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 how to use this guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 16

    Xvi riverstone networks rs 3000/3100/3200 switch router getting started guide 4 initial configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 4.1 powering on the rs 3000/rs 3100/rs 3200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 17

    Riverstone networks rs 3000/3100/3200 switch router getting started guide xvii list of figures figure 2-1 front view of a rs 3000 chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 figure 2-2 front view of a rs 3100 chassis . . . ....

  • Page 18

    Xviii riverstone networks rs 3000/3100/3200 switch router getting started guide figure 3-6 installing the line card into the chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 figure 3-7 gbic module. . . . . . . . . . . . . . . . . . . . . ....

  • Page 19

    Riverstone networks rs 3000/3100/3200 switch router getting started guide xix list of tables table 2-1 iso 7-layer model and rs 3000/3100/3200 capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 table 2-2 technical specifications . . . . . . . . . . . . . . . . . ....

  • Page 20

    Xx riverstone networks rs 3000/3100/3200 switch router getting started guide table 2-35 cabling and connectors for mpls pos oc-3c line card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38 table 2-36 led description for mpls pos oc-3c line card. . . . . . . . . . . . . . . . ...

  • Page 21

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 1-1 1 about this guide this guide provides a general overview of the hardware and software features, and provides procedures for initial installation and set up of the rs 3000/rs 3100/rs 3200. 1.1 how to use this guide 1.2 rel...

  • Page 22

    1-2 riverstone networks rs 3000/3100/3200 switch router getting started guide related documentation about this guide.

  • Page 23

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-1 2 introduction the riverstone rs 3000, rs 3100 and rs 3200 provide non-blocking, wire-speed layer-2 (switching), layer-3 (routing), and layer-4 (application) switching. This chapter provides a basic overview of the rs 3000...

  • Page 24

    2-2 riverstone networks rs 3000/3100/3200 switch router getting started guide specifications introduction 2.2 specifications the rs 3000/rs 3100/rs 3200 hardware provides the wire-speed switching. The software provides the performance monitoring, filtering, and quality of service (qos). The router’s...

  • Page 25

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-3 introduction specifications media interface protocols • 802.3 (10base-t) • 802.3u (100base-tx, 100base-fx) • 802.3x (1000base-sx, 1000base-lx) • 802.3z (1000base-sx, 1000base-lx) • t1/e1 (wan multi-rate) • t3 clear channel...

  • Page 26

    2-4 riverstone networks rs 3000/3100/3200 switch router getting started guide software overview introduction 2.3 software overview this section describes the features and capabilities of the rs 3000, rs 3100 and rs 3200 in greater detail. For full information regarding the use of these features and ...

  • Page 27

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-5 introduction software overview note all other protocols that require routing must be tunneled using ip. By default, the rs 3000, rs 3100 and rs 3200 use one mac address for all interfaces. The rs 3000, rs 3100 and rs 3200 ...

  • Page 28

    2-6 riverstone networks rs 3000/3100/3200 switch router getting started guide software overview introduction 2.3.4 layer-4 switching in addition to layer-2 bridging and layer-3 routing, the rs 3000, rs 3100 and rs 3200 perform layer-4 switching. Layer-4 switching is based on applications and flows. ...

  • Page 29

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-7 introduction software overview • layer-3 source acls (block ip or ipx traffic based on source ip or ipx address) • layer-3 destination acls (block ip or ipx traffic based on destination ip or ipx address) • layer-3 flow ac...

  • Page 30

    2-8 riverstone networks rs 3000/3100/3200 switch router getting started guide software overview introduction layer-3 rmon v2 statistics – statistics for icmp, ip, ip-interface, ip routing, ip multicast, vlan layer-4 rmon v2 statistics – statistics for tcp and udp lfap – light-weight file accounting ...

  • Page 31

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-9 introduction hardware features 2.4 hardware features this section describes the rs 3000/rs 3100/rs 3200’s hardware specifications. For information about installing the chassis and line cards, see chapter 3, "hardware insta...

  • Page 32

    2-10 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction figure 2-3 front view of a rs 3200 chassis you can install line cards in any order in the expansion slots. For example, you could install a module in the first slot and leave the other slot ...

  • Page 33

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-11 introduction hardware features • status leds. Table 2-4 describes the leds. Caution the diag port and the nmi switch on the front panel of the rs 3100 and rs 3200 are for use by riverstone networks, inc. Support personnel...

  • Page 34

    2-12 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction 2.4.4 fans the router contains two fans to provide a cooling air flow across the motherboard and modules. They are located towards the rear of the chassis. Warning to ensure that the fans ca...

  • Page 35

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-13 introduction hardware features warning failure to provide adequate grounding for the ac power supply can result in critical injury and serious damage to the switch router and will invalidate your warranty. Note the rs 300...

  • Page 36

    2-14 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction dc power supply warning failure to provide a connection between the dc power supply and a reliable earth ground can result in serious damage to the switch router and invalidate your warranty...

  • Page 37

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-15 introduction hardware features 2.4.6 line cards the following section lists the various line cards supported on the rs 3000, rs 3100 and rs 3200, their capabilities, and specifications. 10/100base-tx line card the 10/100b...

  • Page 38

    2-16 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction the 10/100base-tx line card uses the following leds. 100base-fx sfp line card the 16-port 100base-fx sfp line card contains 16 independent ethernet ports that can be individually configured ...

  • Page 39

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-17 introduction hardware features • the gigabit ethernet sfp transceiver ports are described earlier in this section. • each sfp transceiver has associated with it a port status led. - if the port is lit green, a link is est...

  • Page 40

    2-18 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction 1000base-sx line card the 1000base-sx line card supplies two independent gigabit (1000-mbps) ethernet ports. The ports connect to mmf optical cable. Figure 2-8 shows the front panel of the 1...

  • Page 41

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-19 introduction hardware features 1000base-lx line card the 1000base-lx line card provides the same features as the 1000base-sx line card, but supports both single-mode fiber (smf) and mmf. Figure 2-9 shows the front panel o...

  • Page 42

    2-20 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction the 1000base-lx line card uses the following leds. Table 2-12 1000base-lx line card specifications port type specification 1000base-lx • 802.3z standard (also uses 802.3x for flow control) •...

  • Page 43

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-21 introduction hardware features 1000base-lh line card the 1000base-lh line card supports smf. Figure 2-10 shows the front panel of the 1000base-lh line card. Figure 2-10 front panel of the 1000base-lh line card per-port tx...

  • Page 44

    2-22 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction the following table lists the media specifications for the 1000base-lh line card. The 1000base-lh line card uses the following leds. Table 2-14 1000base-lh line card specifications port type...

  • Page 45

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-23 introduction hardware features mpls gigabit ethernet gbic line card figure 2-11 shows the front panel of the 2-port mpls activated gigabit interface converter (gbic) line card. Figure 2-11 front panel of mpls gbic line ca...

  • Page 46

    2-24 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction note when the gic-12 gbic is plugged into a port, the link led for the line card is lit even when there isn’t a cable plugged into the gbic. When the gic-12 gbic is plugged into a port, auto...

  • Page 47

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-25 introduction hardware features non-mpls gigabit ethernet gbic line card figure 2-13 shows the front panels of the 2-port non-mpls activated gigabit interface converter (gbic) line cards. The g3m-gbcfm-02 is used with the ...

  • Page 48

    2-26 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction gbic modules provide the media-specific portion of the gigabit gbic line-card, which support gigabit ethernet connectivity across multiple media types and distances. The gigabit gbic line ca...

  • Page 49

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-27 introduction hardware features note when the gic-12 gbic is plugged into a port, the link led for the line card is lit even when there isn’t a cable plugged into the gbic. When the gic-12 gbic is plugged into a port, auto...

  • Page 50

    2-28 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction dual serial and quad serial – c/ce line cards the dual serial line card contains a single dual serial wan port (two serial ports located on one high density connector). The quad serial – c a...

  • Page 51

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-29 introduction hardware features riverstone dual serial and quad serial–c/ce line cards use standard copper twisted-pair cable with one of four custom remote-end connectors to attach to their respective csu/dsu connectors. ...

  • Page 52

    2-30 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction riverstone offers four cables, listed in table 2-22 , used to connect the rs 3000, rs 3100 and rs 3200 to standard csu/dsu connectors. The dual serial and quad serial – c/ce line cards use t...

  • Page 53

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-31 introduction hardware features dual hssi line card the dual hssi line card contains two 50-pin high speed serial interface (hssi) ports. Figure 2-19 shows the front panel of the dual hssi wan line card. Figure 2-19 front ...

  • Page 54

    2-32 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction the dual hssi line card uses the following leds. Atm multi-rate line card the atm multi-rate line card houses various physical layer (phy) interface cards in its two available slots. Atm phy...

  • Page 55

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-33 introduction hardware features figure 2-21 front panel of atm multi-rate line card see section 3.3.4, "installing the atm phy cards" for instructions on installing phys into the atm multi-rate line card. The atm multi-rat...

  • Page 56

    2-34 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction multi-rate wan line card the multi-rate wan line card can contain two wan interface cards (wics). Figure 2-22 shows the front panel of the multi-rate wan line card with one wic installed. Th...

  • Page 57

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-35 introduction hardware features figure 2-23 t1 and e1 wics each clear channel t3/e3 wic contains a transmit and a receive port that provide a single wan interface. Figure 2-24 clear channel t3 and e3 wics table 2-29 throug...

  • Page 58

    2-36 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction table 2-33 lists the pin assignments for both the rj-48c connector on the t1 wic and the rj-45 connector on the e1 wic. Table 2-31 specifications for clear channel t3 wic card port-type spec...

  • Page 59

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-37 introduction hardware features the multi-rate wan line card and all wics use the following leds: table 2-34 leds for multi-rate wan line card and wics led description offline when lit, this amber led on the left side of t...

  • Page 60

    2-38 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction mpls pos oc-3c line card the mpls oc-3c line card supports multi-protocol label switching (mpls) at the oc-3c line rate. It is designed to use small form-factor pluggable (sfp) connectors. F...

  • Page 61

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-39 introduction hardware features advanced services module riverstone’s advanced services module (asm) is a 1-slot, 2-port gigabit ethernet linecard that provides quality of service (qos) capabilities for ethernet networks. ...

  • Page 62

    2-40 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction • single-rate shaping – rate-shapers configured with only a committed access rate (car) • dual-rate shaping – rate-shapers configured with a car and a burst size • shaper groups – rate-shape...

  • Page 63

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-41 introduction hardware features note when the gic-12 gbic is plugged into a port, the link led for the line card is lit even when there isn’t a cable plugged into the gbic. When the gic-12 gbic is plugged into a port, auto...

  • Page 64

    2-42 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction offline when lit, this amber led indicates that the line card is offline (powered off) and is ready for hot swap. The offline led also is lit briefly during a reboot or reset of the rs and g...

  • Page 65

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-43 introduction hardware features 2.4.7 cwdm gbics all gigabit ethernet ports on the rs can be configured for coarse wavelength division multiplexing (cwdm) through use of cwdm gbics. Cwdm allows a single fiber to carry up t...

  • Page 66

    2-44 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction figure 2-29 describes a cwdm ring configuration. In this example, four ports on an rs switch/router are configured with cwdm gbics tuned to different wavelengths. Each of the four gbics are ...

  • Page 67

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 2-45 introduction hardware features gic-cwdm-1510 • single-mode fiber interface • terminated with sc connectors • 1510 nm wavelength gic-cwdm-1530 • single-mode fiber interface • terminated with sc connectors • 1530 nm wavelen...

  • Page 68

    2-46 riverstone networks rs 3000/3100/3200 switch router getting started guide hardware features introduction.

  • Page 69

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-1 3 hardware installation this chapter provides hardware installation instructions and information on safety considerations, environmental considerations, and regulatory standards. 3.1 safety considerations en espanol -- app...

  • Page 70

    3-2 riverstone networks rs 3000/3100/3200 switch router getting started guide safety considerations en espanol -- appendix b hardware installation warning make sure you allow at least three inches of room for air flow around the rs 3000, rs 3x00 or rs 3200 chassis..

  • Page 71

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-3 hardware installation specifications 3.2 specifications table 3-1 lists physical, electrical, and environmental specifications for the rs 3000, rs 3x00 and rs 3200. 3.3 installing the hardware hardware installation of the ...

  • Page 72

    3-4 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation 3.3.2 installing line cards before installing the rs 3000, rs 3x00 or rs 3200 into an equipment rack, it is recommended that you first install any expansion line cards that you...

  • Page 73

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-5 hardware installation installing the hardware figure 3-1 removing the rs 3000, rs 3x00 or rs 3200’s cover 5. Slide the cover away from the front of the rs 3000, rs 3x00 or rs 3200 about one-half inch (1/2”), then lift the ...

  • Page 74

    3-6 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation figure 3-3 installing “standard” line card face plate (view from inside chassis) figure 3-4 “extended” emi face plate.

  • Page 75

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-7 hardware installation installing the hardware figure 3-5 installing the extended emi face plate 8. Insert the line card from the top and ensure that it makes maximum surface contact with its face plate. 9. Line up the two ...

  • Page 76

    3-8 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation figure 3-6 installing the line card into the chassis warning the female and male connectors are not keyed, so it is possible to misalign the connection. Ensure that all pins fi...

  • Page 77

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-9 hardware installation installing the hardware figure 3-7 shows an example of a gbic module. The procedure following the figure describes how to install the module into the gbic line card. Figure 3-7 gbic module to install ...

  • Page 78

    3-10 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation figure 3-8 inserting a gbic module 2. Gently insert the gbic module into the gbic slot opening. The gbic door on the line card folds in, and the internal guides engage the ali...

  • Page 79

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-11 hardware installation installing the hardware figure 3-9 installing an atm phy card to install a phy card into an atm line card: 1. Use a phillips screwdriver to loosen the two captive screws that hold the option slot cov...

  • Page 80

    3-12 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation setting jumpers on the clear channel t3/e3 wics both the clear channel t3 and e3 wics contain a set of jumpers (jp2, jp3,and jp4). These jumpers allow you to set whether the s...

  • Page 81

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-13 hardware installation installing the hardware figure 3-10 jumper position on clear channel t3 and e3 wics installing the multi-rate line card because of its design, the multi-rate wan line card requires a somewhat differe...

  • Page 82

    3-14 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation 8. Remove the two front-most stand-offs from the motherboard as shown in figure 3-11 . Figure 3-11 removing the standoffs on the motherboard 9. Use the #2 phillips-head screwd...

  • Page 83

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-15 hardware installation installing the hardware figure 3-12 installing a wic 14. Push the wic card into the wic receptacle until the 96-pin connector is firmly seated into the connector at the back of the receptacle. 15. Us...

  • Page 84

    3-16 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation warning before performing any mechanical upgrade or installation procedures, make sure that the rs is powered off. Advertencia antes de llevar a cabo cualquier actualización m...

  • Page 85

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-17 hardware installation installing the hardware 3.3.7 management ports the rs 3000 has two ports for attaching management devices: male db-9 dce port – this serial port is used for direct connection to a terminal or pc runn...

  • Page 86

    3-18 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation connecting a 10/100base-tx management cable use the rj-45 10/100base-tx dte port for connecting the rs 3000 to your network for in-band management through either telnet or snm...

  • Page 87

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 3-19 hardware installation installing the hardware table 3-4 wiring map for mdi management cable signal (rs 3000 port) pin signal (management console port) txd (transmit data) 1 rxd (receive data) a txd (transmit data) 2 rxd (...

  • Page 88

    3-20 riverstone networks rs 3000/3100/3200 switch router getting started guide installing the hardware hardware installation.

  • Page 89

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-1 4 initial configuration this chapter provides the following information on powering up the rs 3000 for the first time, and performing basic setup procedures. Basic setup includes: • powering on the rs 3000/rs 3100/rs 3200 ...

  • Page 90

    4-2 riverstone networks rs 3000/3100/3200 switch router getting started guide powering on the rs 3000/rs 3100/rs 3200 initial configuration if this is the first time you have powered on the rs 3000/rs 3100/rs 3200, it boots automatically using the software image on the internal flash memory. While t...

  • Page 91

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-3 initial configuration powering on the rs 3000/rs 3100/rs 3200 4. When the software is fully booted, the following messages appears on the management console: 5. As prompted, press return (or enter) to activate the command ...

  • Page 92

    4-4 riverstone networks rs 3000/3100/3200 switch router getting started guide starting the command line interface initial configuration 4.2 starting the command line interface to start the command line interface (cli), power on the system, as described in section 4.1, "powering on the rs 3000/rs 310...

  • Page 93

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-5 initial configuration starting the command line interface 4.2.2 basic line editing commands the cli supports emacs-like line editing commands. The following table lists some commonly used commands. For a complete set of co...

  • Page 94

    4-6 riverstone networks rs 3000/3100/3200 switch router getting started guide configuration changes and saving the configuration file initial configuration 4.3 configuration changes and saving the configuration file the rs 3000 uses three special configuration files: caution the active configuration...

  • Page 95

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-7 initial configuration configuration changes and saving the configuration file 4. Enter y to activate the changes. Note if you exit the configure mode (by entering the exit command or pressing ctrl+z), the cli will ask you ...

  • Page 96

    4-8 riverstone networks rs 3000/3100/3200 switch router getting started guide configuration changes and saving the configuration file initial configuration 4.3.3 viewing the current configuration to view the current configuration: 1. Ensure that you are in enable mode by entering the enable command....

  • Page 97

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-9 initial configuration setting the basic system information 4.4 setting the basic system information follow the procedures in this section to set the following system information: • system time and date • system name • syst...

  • Page 98

    4-10 riverstone networks rs 3000/3100/3200 switch router getting started guide setting the basic system information initial configuration here is an example: 5. Use the interface add ip command to set the ip address and netmask for the en0 ethernet interface. The en0 ethernet interface is used by th...

  • Page 99

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-11 initial configuration setting the basic system information 9. Save the active configuration to the startup configuration file using the following command: 10. When the cli displays the following message, enter y to save t...

  • Page 100

    4-12 riverstone networks rs 3000/3100/3200 switch router getting started guide setting up passwords initial configuration 4.5 setting up passwords you can password-protect cli access to the rs 3000, rs 3100 or rs 3200, by setting up passwords for user mode access, enable mode access, and diag mode a...

  • Page 101

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-13 initial configuration setting up passwords caution test all new passwords before saving the active configuration to the startup configuration file. 4.5.1 if you forget your passwords if you forget your passwords follow th...

  • Page 102

    4-14 riverstone networks rs 3000/3100/3200 switch router getting started guide setting up passwords initial configuration here is an example: 5. When the rs 3000, rs 3100 or rs 3200 finishes booting, enter the following commands (when prompted, answer yes ): 6. The user, enable, and diag access mode...

  • Page 103

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-15 initial configuration setting up snmp 4.6 setting up snmp to use snmp to manage the rs 3000, rs 3100 or rs 3200, you need to set up an snmp community and specifying the ip address of the target host for snmp traps. Otherw...

  • Page 104

    4-16 riverstone networks rs 3000/3100/3200 switch router getting started guide setting up snmp initial configuration by default, snmp information is sent and received on the rs 3x00’s en0 ethernet port. If you want snmp to use a different port on the rs 3x00, use the following command. Here is an ex...

  • Page 105

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-17 initial configuration setting up snmp for additional information about rs 3000, rs 3100 or rs 3200 security and acls, see the riverstone rs switch router user guide. 4.6.3 supported mibs the following lists the mibs that ...

  • Page 106

    4-18 riverstone networks rs 3000/3100/3200 switch router getting started guide setting up snmp initial configuration ctron-ssr-service-status (deprecated) 6/27/00 ctron-ssr-capacity-mib 6/27/00 riverstone-inventory- mib 8/22/01 riverstone-mpls-mib 5/24/02 riverstone-queue-mib 6/12/02 riverstone-vlan...

  • Page 107

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-19 initial configuration setting the dns domain name and address 4.7 setting the dns domain name and address associating a dns name server with your rs 3000, rs 3100 or rs 3200 allows you to use device names (rather than ip ...

  • Page 108

    4-20 riverstone networks rs 3000/3100/3200 switch router getting started guide setting the dns domain name and address initial configuration 7. Exit configure mode, then enter the system show dns command to verify the new dns settings. Here is an example: 8. Use the ping command to verify that the r...

  • Page 109

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 4-21 initial configuration setting the syslog parameters 4.8 setting the syslog parameters the rs 3000, rs 3100 or rs 3200 can use syslog messages to communicate the following types of messages to a syslog server: table 4-6 sh...

  • Page 110

    4-22 riverstone networks rs 3000/3100/3200 switch router getting started guide setting the syslog parameters initial configuration note the is a string of the form: user, kern, or local0 through local7. These strings are reserved by the syslog server daemon. For information on how is used by the sys...

  • Page 111

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 5-1 5 managing software this chapter describes how to perform operations regarding rs 3000, rs 3100 or rs 3200 operating software and bootprom images software. The following topics are covered: • upgrading the system image sof...

  • Page 112

    5-2 riverstone networks rs 3000/3100/3200 switch router getting started guide upgrading system image software managing software note the is the full directory path and filename to the image software file on the tftp server. Here is an example: 4. Enter the system image list command to list the image...

  • Page 113

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 5-3 managing software upgrading boot prom software note you do not need to activate this change. 7. Reboot the rs 3000, rs 3100 or rs 3200 to load and run the new system software image. 5.2 upgrading boot prom software the rs ...

  • Page 114

    5-4 riverstone networks rs 3000/3100/3200 switch router getting started guide upgrading boot prom software managing software here is an example: 4. Reboot the rs 3000, rs 3100 or rs 3200. 5. Enter the system show version command to verify that the new boot prom software is in the internal memory of ...

  • Page 115

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 5-5 managing software loading software from the network 5.3 loading software from the network typically, the rs 3000 loads its operating software from the flash memory contained on the motherboard. Alternately, the rs 3000 can...

  • Page 116

    5-6 riverstone networks rs 3000/3100/3200 switch router getting started guide loading software from the network managing software here is an example: 6. Enter the set command to view the changes: here is an example: 7. From the boot prompt, use the ping command to verify that the rs 3000 can reach t...

  • Page 117

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 5-7 managing software loading software from the network 5.3.2 loading image software from a bootp/tftp server the rs 3x00 contains a bootp client and can be configured to obtain its image software from a bootp/tftp server. Usi...

  • Page 118

    5-8 riverstone networks rs 3000/3100/3200 switch router getting started guide upgrading fpga code managing software 6. Reboot the rs 3000, rs 3100 or rs 3200 by entering the reboot command at the boot prompt. Here is an example: 5.4 upgrading fpga code on occasion, riverstone networks may make upgra...

  • Page 119

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 5-9 managing software upgrading fpga code 1. Load the fpga code onto the tftp server. Make sure that the rs can reach the server across the network. 2. Enter the system linecard upgrade command, specifying the ip address of th...

  • Page 120

    5-10 riverstone networks rs 3000/3100/3200 switch router getting started guide upgrading fpga code managing software 3. After the fpga upgrade process completes, the line card starts passing traffic. Notice in the example above that the hot swapping out and in occurs as part of the upgrade process –...

  • Page 121

    Riverstone networks rs 3000/3100/3200 switch router getting started guide 5-11 managing software upgrading fpga code 3. Use the system linecard upgrade command to upgrade the line card with the fpga code in flash ram in slot0 . Notice that only the filename is specified – the rs knows the correct pa...

  • Page 122

    5-12 riverstone networks rs 3000/3100/3200 switch router getting started guide upgrading fpga code managing software.

  • Page 123

    Riverstone networks rs 3000/3100/3200 switch router getting started guide -1 appendix a troubleshooting if you experience difficulty with the basic hardware or software setup procedures in this guide, check the following table to see whether the difficulty you are experiencing is described. If you f...

  • Page 124

    -2 riverstone networks rs 3000/3100/3200 switch router getting started guide configuration changes do not seem to be taking effect. Reactivate the changes using the procedure in section 4.3.1, "activating the configuration commands in the scratchpad." configuration changes are not reinstated after a...

  • Page 125

    Riverstone networks rs 3000/3100/3200 switch router getting started guide -1 appendix b international safety information b.1 consideraciones de seguridad lea las siguientes advertencias relacionadas con la seguridad y el uso del equipo para evitar posibles lesiones personales o daños al producto. B....

  • Page 126

    -2 riverstone networks rs 3000/3100/3200 switch router getting started guide consideraciones de seguridad.

  • Page 127

    Riverstone networks rs 3000 switch router getting started guide index-1 index numerics 10/100base-tx line card ....................... 2-15 1000base-lh line card overview .......................................... 2-21 1000base-lx line card overview .......................................... 2-19 10...

  • Page 128

    Index-2 riverstone networks rs 3000 switch router getting started guide index active .................................................. 4-6 dns domain name and address ....... 4-19 en0 ethernet interface ...................... 4-10 saving ................................................. 4-6 scratch...

  • Page 129

    Riverstone networks rs 3000 switch router getting started guide index-3 index 1000base-lx .......................2-20 , 2-22 1000base-sx ................................. 2-18 atm oc-3c ..................................... 2-33 chassis .............................................. 2-11 dual hssi ....

  • Page 130

    Index-4 riverstone networks rs 3000 switch router getting started guide index remote monitoring .................................... 2-3 rip ............................................................ 2-5 v1 ....................................................... 2-5 v2 ...............................

  • Page 131

    Riverstone networks rs 3000 switch router getting started guide index-5 index system image choose ................................ 5-2 system image list ...................................... 5-2 system information ................................... 4-9 system messages ................................