RJM MasterMind User Manual - page 19

13 

RENA -  Remote Enable 

(Enable range: On, OFF, Default value: OFF) 

Turning this parameter on enables remote access mode, where two or more MasterMinds can be linked together and 

synchronized. See the 

Remote Access

 section for more details. Press 3 / CC On/Off to toggle this parameter on or off. If 

you’re connecting something other than a MasterMind to the Remote In port, this parameter should be set to OFF. 

rCCh -  MIDI Receive Channel 

(MIDI Ch range: CH01 - CH16, CH-- (MIDI receive disabled) , Default value: CH--) 

Sets the MIDI channel on which the MasterMind receives Program Change messages. Press 5 / MIDI Ch to select the 

MIDI Channel. If this is enabled, a Program Change message coming in on the Remote In port will cause a preset to be 

selected and the MasterMind will send all of the MIDI messages for that preset, just as if the preset was selected from 

the front panel buttons.  

IA - 

Instant Access 

(Instant Access range: On, OFF, Default value: OFF) 

Turning on this parameter will enable Instant Access mode. With this parameter on, the Function button will activate 

Instant Access mode, regardless of any other Function button related settings. See the Instant Access Mode section for 

more details. 

SNDA -  Send Always 

(Send Always range: On, OFF, Default value: On) 

When this parameter is on, pressing a preset button (1 through 5) will always cause the MasterMind to send the 

corresponding PC and CC messages, even if the MasterMind is already on the selected preset. If this parameter is off, 

the MasterMind will only send PC and CC messages when selecting a new preset – pressing the same preset button 

repeatedly will not generate multiple sets of PC and CC messages. 

SEND -  MIDI Dump Send 

(Yes/No selection: Press Bank Up (Yes) to send, Bank Down (No) to exit Setup Mode) 

Pressing Bank Up when this parameter is selected will cause the MasterMind to send its configuration data out the MIDI 

Out port. If the MIDI Out port is connected to the MIDI In port of another MasterMind, the data will be transferred to the 

MasterMind. The data can also be sent to a PC that has a MIDI interface and Sysex librarian software for backup 

purposes. 

InIt -  Initialize 

(Yes/No selection: Press Bank Up (Yes) to initialize, Bank Down (No) to exit Setup Mode) 

Pressing Bank Up when this parameter is selected will cause the MasterMind to erase its memory, returning to the 

factory default state. Be careful! This wipes the entire memory and there’s no way to restore your settings unless you 

have previously backed them up to a PC or another MasterMind. 

Preset Setup 

Once you’ve finished 

Global Setup

, you can set up each preset. In this mode, you set which Program Change number is 

sent to each Program Change destination, and set which controller value is sent for each Continuous Controller for 

every preset. You can also set up the Function button and Expression Pedal for each preset in this mode. 

Entering Preset Setup 

The MasterMind goes straight to Preset Setup when you enter 

Setup Mode

. If you happen to be in 

Global Setup

, you 

can press the 1 / Function Select button to switch to Preset Setup. The red LED above the 1 / Function Select button 

will light to tell you that Preset Setup is active. You are now ready to edit the first parameter. 

Watching the display, you’ll see that it alternates between displaying the current preset number, PC1 and a program 

change number. If you’re on preset 001 and haven’t changed anything from the defaults, you’ll see it alternate between  

P001, PC1 and =001. This means that, for preset 001, it will send program change #1 to PC1. (Remember that PC1 is a 

destination for Program Change messages and was set to a specific MIDI channel in 

Global Setup

).