Installation manual.
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production ii hd1012 installation manual for v3 software issue 1, revision 1, september 2003 © 1998-2003 snell & wilcox post production division the business and technology centre shire hill saffron walden...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page iii safety explanation of safety symbols this symbol refers the user to important information contained in the accompanying literature. Refer to users manual. This symbol indicates that hazardou...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production iv power cable supplied for the usa the equipment is shipped with a power cord with a standard iec molded free socket on one end and a standard 3-pin plug on the other. If you are required to re...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page v maintenance & repair there are no user serviceable parts within either the mainframe or the control panel. In the unlikely event of an equipment failure contact the snell & wilcox post product...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production vi emc standards this unit conforms to the following standards: bs en 55103-1 : 1997 electromagnetic compatibility, product family standard for audio, video, audio-visual and entertainment light...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page vii contents section a - installation ........................................................................................... 1 introduction ....................................................
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production viii list of diagrams wiring of iec mains inlet connectors ................................................................... 4 control panel - rear view...........................................
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 1 section a installation.
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 2 introduction these installation instructions provide a guide to the installation of the hd1012 high-definition switchers. On delivery of the system the equipment is supplied in dedicated packa...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 3 location and environment environmental considerations the ambient temperature for all the supplied equipment should not exceed the limits of 5 and 35 degrees c. At a relative humidity of 10 to...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 4 location and environment - continued power supplies the switcher mainframe and/or control panel may be fitted with dual power supplies. In each case the unit will work happily with a single po...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 5 system interconnection introduction your system has been set up and tested before shipment. Installation normally consists of siting and interconnecting the system components, connecting video...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 6 system interconnection - continued button bus multi control button bus multi control is a facility which allows one switcher control panel to control two switcher mainframes simultaneously, so...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 7 system interconnection - continued display 2 display 1 vga mainframe 10 base t rs232 model no. Serial no. Made in saffro n walden, essex, uk. Snell & wilcox 115/230 v 60/50 hz 1.0/0.5 a t 250v...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 8 system interconnection - continued cp1512 dimensions in mm 819 824.
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 9 system interconnection - continued hd1000 switcher mainframe - rear panel & connectors.
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 10 system interconnection - continued inputs connect up to 12 hd-sdi inputs to the 12 serial inputs of the switcher mainframe. Sources can be either video or key. Outputs connect the program, cl...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 11 system interconnection - continued multiple monitor mode multiple monitor mode is a set-up that allows monitoring of m/e program and preview as well as p/p program and preview. Four manitors ...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 12 system timings referencing the switcher can be genlocked to any of its 12 hd-sdi inputs or to tri-level sync. On the ref analogue in loop-through connectors, selectable from the configure-sys...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 13 system timings - continued referencing - system delays the total delay through the system depends partly on the current standard but mainly on which cards are fitted to the hd1000 mainframe. ...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 14 control ports and protocols ports the switcher mainframe has ethernet, serial and tally & gpi i/o ports. The ethernet ports are used for connection between the mainframe and the control panel...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 15 control ports and protocols - continued gvg 4000 this protocol allows an editor capable of controlling a gvg 3000 or 4000 switcher to drive the p/p bus of the switcher. Learn and recall of dm...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 16 control ports and protocols - continued there are three variants of the gvg-3000/4000 protocol. They are identical except for the way that aux and preview busses are assigned. The bus name in...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 17 control ports and protocols - continued sony dvs crosspoint allocation is shown in the table below. When a source can be accessed via two or more different values, the value returned on a sta...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 18 control ports and protocols - continued using a sony bve-9100 editor there is a fairly common problem when using the bve-9100 editor and s & w switchers whereby the switcher appears to be act...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 19 control ports and protocols - continued to adjust this setting on the bve-9100 step-by-step: 1. Press shift-setup. 2. Press f3 idc. 3. Cursor down to the sw/mon entry in the idc list 4. Press...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 20 control ports and protocols - continued vtr using the sony vtr (p2) protocol, the switcher emulates, specifically, a sony bvh-2000. The timeline is treated as length of videotape in a virtual...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 21 control ports and protocols - continued s & w tally this protocol transmits detailed tally information every field for use by external intelligent tally systems. The protocol used is specific...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 22 control ports and protocols - continued general purpose inputs & outputs overview standard system the switcher mainframe has eight general purpose inputs and 32 outputs. The action of each of...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 23 control ports and protocols - continued the outputs there are thirty-two general purpose outputs, located on the three tally connectors (25 way d-type) on the rear of the switcher mainframe. ...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 24 control ports and protocols - continued programming the inputs the gpi functions are programmed in the gpi menu found under the configure - user menu. The left screen shows the, standard, eig...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 25 control ports and protocols - continued programming the outputs the gpo functions are programmed in the gpo menu which is accessed from the gpi menu by f1r. The rotary controls are used to se...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 26 control ports and protocols - continued multiple conditions the gpo active state may be conditional on more than one occurrence. The rightside buttons f1r to f4r set-up the conditions and the...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 27 control ports and protocols - continued list of gpo occurrences the following is a complete list of the system occurrences which may be assigned to a gpo. Note this list includes the occuranc...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 28 other installation procedures setting the real-time clock it is recommended that you set the real-time clock at installation time. To do this, press the config button near the bottom-left of ...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 29 other installation procedures – continued remote allocation of aux sources the switcher auxiliary outputs may have their sources allocated from one or more remote panels rather than from the ...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 30 other installation procedures – continued quartz panels the quartz electronics cp3201 - s7 remote panel may be used to switch signal sources to the switcher auxiliary outputs from a location ...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 31 other installation procedures – continued 1. All aux o/ps controlled from one panel. The quartz and pro-bel remote panels have buttons which select the required aux output. The panels are con...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 32 other installation procedures – continued diode buffer 9 pin “d”- type female connector (to extender) wiring of pins between connectors 9 pin “d”- type male connector (to control panel) descr...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 33 other installation procedures – continued interconnection & set-up the diode buffers connect directly to the computer port of the quartz panel or the loop port of the pro-bel panel. A standar...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 34 connector pinouts mainframe rs-422 connector pinout 9-way female d-type function 1 frame ground 2 transmit a (tx-) 3 receive b (rx+) 4 receive common 5 6 transmit common 7 transmit b (tx+) 8 ...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 35 connector pinouts - continued switcher gpis / gpos 25 way d-type connectors - switcher mainframe rear panel tally 1-12 tally 13-24 tally 25-32 & gpi 1-8 pin signal pin signal pin signal 1 gpo...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 36 cable wirings control panel to lcd touch screen 15-way cable control panel 15-way sub-d-type male cable colour lcd touch screen 15-way sub-d-type male lcd_lcds0– lcd_lvds1– pin 1 pin 2 pair 1...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 37 cable wirings - continued control panel to lcd touch screen 44-way cable control panel 44-way sub-d-type male cable colour lcd touch screen 44-way sub-d-type male gnd pin 1 white-blue pin 1 g...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 38 system with integrated router an integrated router may by used with the hd1012 system to increase the number of available sources. This router may be the snell & wilcox hd1132 or a supported ...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 39 router / mainframe connections diagram 1 2 3 4 5 6 7 8 9 10 11 59 60 61 62 63 64 ref loop source source source source 1 2 59 60 rs422 aux 5 aux 6 aux 7 aux 8 12 1 2 1 2 3 4 5 6 7 8 9 10 11 12...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 40 deliberately blank.
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 41 section b specifications.
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 42 the following specifications cover the hd1000 switcher mainframe and cp1512 control panel. Television standards television standards multi-standard, including, but not necessarily limited to,...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 43 inputs number of video inputs 12 x high definition serial digital interface (hd-sdi) each on 1 x bnc reference input on-line switchable between: from any (hd-sdi) video input. Analogue hd syn...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 44 outputs program outputs 2-off hd-sdi each on 1 x bnc, on-line switchable between 8 & 10 bits. Clean program outputs 2-off hd-sdi each on 1 x bnc, on-line switchable between 8 & 10 bits. Previ...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 45 control interfaces - mainframe control panel 10 base t-x on 1 x rj45 connector. Network #1 10 base t on 1 x rj45 connector. 10 base 2 on 1 x bnc. Network #2 (optional) 10/100 base t on 1 x rj...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 46 control interfaces - control panel main chassis mainframe 10 base t on 1 x rj45 connector. Built-in display 1 x 25-way female d-type. 1 x 9-way female d-type. External keyboard pc compatible ...
Www.Snellwilcox.Com s&w production & post production hd1012 installation manual – v3, issue 1, rev 1 page 47 physical - hd1000 switcher mainframe size height width depth 8u (rack units) ~ 356 mm. 19 inches nominal ~ 485 mm including brackets. 24 inches nominal ~ 610 mm including connectors weight 48...
Www.Snellwilcox.Com page hd1012 installation manual – v3, issue 1, rev 1 s&w production & post production 48 power supply switcher mainframe two fully-independent hot-swappable psu modules, with separate mains power feeds via 2 x iec socket. Control panel two fully-independent psu modules, with sepa...
Www.Snellwilcox.Com s&w production & post production end of manual.