SABINE SW75-T BELTPACK TRANSMITTER Quick Setup Manual

LIT-SW75T-QG-EN-070223.pmd

SIDE

A

© 2007 Sabine, Inc.

Select PAD setting: Use the UP

or DOWN buttons to select the

desired setting. Selection is

stored after 3 seconds.

3

Check for Clipping: Make sure

the receiver’s Audio Level Meter

stays out of the Clipping Zone.

♦ Electric guitars

low-gain pickups

♦ Microphones

higher gain

♦ Electric guitars

standard

-10 dB

-17 dB

-23 dB

-26 to -34 dB

-37 dB

♦ Instruments

high-gain pre-

amps

Toggles between no filter and 12 dB/octave low frequency roll-off filter

(starting at 75 Hz).

Select LOW CUT setting: Use the UP or DOWN

buttons to toggle between no filter (indicated in the

display as L 0) or a roll-off at 75 Hz (indicated by L 75).

Resets the display that indicates the length of power-on time (hours and minutes) since the last

battery change or recharge.

To Reset Run-time hours: Simultaneously press

and hold both the UP and DOWN arrows until LCD

resets to 0.00.

Clipping

Zone

As in all audio equipment, the setting of the input level is crucial to achieving the best sound quality.  Setting

minimal PAD levels (-3, -6, or -10 dB) may produce a distorted sound if you are using a high output microphone

or instrument.   Conversely, setting a more extreme PAD level (-40, -37, or -34 dB) may require you to raise

your system gain unnecessarily, resulting in a noisier output.  Set your level so there are at least three indica-

tors illuminated on the audio meter, with an occasional move to the fourth indicator.  The fifth and biggest

indicator denotes clipping.  If you see clipping, choose a lower pad setting (for example, go from -10 to -14 dB).

Select the INPUT to Match your Input Type

SW75-T Beltpack Transmitter Quick Setup Guide

NOTE:  Electric Guitar & Bass: For best results, put your receiver’s FBX Feedback Exterminator into

BYPASS mode. BYPASS is accessible via the receiver front panel or Remote Software control.

Select INPUT function: Push the transmitter’s

SELECT button to scroll through functions until

the word INPUT appears at bottom in the trans-

mitter LCD, which stays backlit while you are

editing all parameters.

2

Select INSTR or MIC: Use the UP or DOWN but-

tons to select your desired input (Instrument or

Microphone).  This important selection optimizes

the input section of the transmitter.  Your selection

is stored after 3 seconds.

Select PAD function: Press the

SELECT button to scroll through

functions until PAD flashes in the

transmitter LCD.

Adjust PAD Settings to Match your Input Level

MICROPHONE

INSTRUMENT

1

1

1

2

2

To view Run-time Hours:  Use the

transmitter’s SELECT button to scroll

through functions until TIME appears in

the LCD.

Suggested PAD Settings - adjust for your application

♦ Microphones

low-output

♦ Microphones

standard

♦ Acoustic

instruments

low-gain pickups

Select LOW CUT function: Push the

transmitter’s SELECT  button to scroll through

functions until L 0 or L 75 appears on the transmit-

ter LCD.

2

2

Changing PAD Settings

Set Low-Cut Filter to Match your Sound

Battery RUN TIME Hours

3

1

4

1

General

PA

D

USER TIP: 

FOR

ELECTRIC

GUITARS

 & 

BASSES

USE

 L0;

SOME

ACOUSTIC

INSTRUMENTS

MAY

BENEFIT

FROM

 L75.

NOTE: 

RUN

-

TIME

HOURS

ARE

RESET

AUTOMATICALLY

WHEN

CHARGING

BATTERIES

.

PLEASE

CAREFULLY

READ

THE

OPERATING

GUIDE

FOR

COMPLETE

INSTRUCTIONS

.

Sabine

♦ SWT31L-TA4

Cardioid Lav

♦ SWTVT50-TA4

Omni Lav

♦ SVT40L-TA4

   Omni Lav

♦ SVT80BW-TA4

♦ SVT81LW-TA4

 Cardioid Headworns

♦ SWT73W-TA4

♦ SWT56W-TA4

   Cardioid

   Headworns

♦ SVT70LW-TA4

♦ SVT70BW-TA4

    Omni

   Headworns

SELECT

UP

DOWN

SELECT

UP

DOWN

SELECT

UP

DOWN

UP

DOWN