1. DL manuals
  2. Saeco
  3. Coffee Maker
  4. IDEA
  5. Idea Instruction And Maintenance Manual

Saeco IDEA Idea Instruction And Maintenance Manual

Other manuals for IDEA: Manual, Instruction And Maintenance
Manual is about: Automatic espresso coffee machine

Summary of IDEA

  • Page 1

    Automatic espresso coffee machine model idea instruction and maintenance manual type: cap002/a/b espresso italia pty ltd www.Espressoitalia.Com.Au freecall 1300 660 976.

  • Page 2

    English 148 1 - machine composition. ................................... 149 2 - reference notes. ............................................... 150 2.1 abbreviations ............................................. 150 2.2 editorial symbols ......................................... 150 3 - user. .......

  • Page 3

    English 149 1 - machine composition a ce label 1 left hand side panel 2 glass 3 back panel 4 cup warming plate 5 pre-ground coffee door 6 coffee bean hopper 7 right hand side panel 8 control panel 9 rubber protector 10 spout clamp (cappuccino set-up) 11 hot water spout (except coffee set-up) 12 stea...

  • Page 4

    English 150 2 - reference notes 2.1 abbreviations f. = figure p. = page p r . = paragraph t. = table 2.2 editorial symbols warning! Pay the utmost attention to the meaning of symbols. They are aimed at drawing the attention of the reader on technical notions or safety warnings. Therefore they have t...

  • Page 5

    English 151 • the routine maintenance has to be carried out only by competent or adequately trained personnel, having the necessary psychophysical requirements, in the whole respect of the instructions mentioned below and according to the current safety and health regulations. • it is strictly forbi...

  • Page 6

    English 152 8.4 brew group the position of this group (22) can be adjusted according to the height of the container used . It is possible to position the brew group on the top or on the bottom. Many brewing heights can be thus obtained. 8.5 cappuccinatore group (f. 4) the cappuccinatore group, is co...

  • Page 7

    English 153 10 - installation 10.1 location notes • the machine has to be installed in a dry and protected place, at the following ambient temperature : 10 ° c - 40° c; maximum humidity: 90%. 10.2 machine positioning note - check if the surface where the machine is installed has the adequate dimensi...

  • Page 8

    English 154 10.5 serial port connection through the serial port the machine can be connected to the authorized customer service center’s equipment, for checks or programming operations (a - f. 10). • check if the electric cables of the system are proportioned to the machine power consumption. The co...

  • Page 9

    English 155 12.1 machine statuses with regard to the power supply, the machine can have the following statuses: off and electrically insulated - main switch (18) and all-pole switch on the ”0“ position (or plug disconnected). - only the memory for the programmed data storing is enabled. On - main sw...

  • Page 10

    English 156 12.5 control panel the brewing buttons have to be pressed for less than 1 second. It switches the machine tem- porarily on (“standby”) and confirms the buttons (h - g) selection. F 1 strong coffee weak strong weak strong 2 strong coffee 1 weak coffee 2 weak coffee light coffee brewing ob...

  • Page 11

    English 157 steam (except coffee set-up) • immerse the spout (17) in the beverage to be heated. • turn the knob counterclockwise (12). When the required temperature is reached, close the knob (clockwise). After every operation, clean the steam spout with a (damp and clean) cloth/sponge from the resi...

  • Page 12

    English 158 coffee coffee with a dash of milk cappuccino hot milk coffe in jug hot water start stop start stop start stop start stop start stop start stop start stop start stop brewing brewing brewing brewing brewing brewing brewing brewing - hold - - hold - - hold - - hold - - hold - - hold - - hol...

  • Page 13

    English 159 12.7 menu programmable functions note - the machine allows some adjustments and setting-ups through the menu programming, in order to meet all customer requirements. During the programming the following buttons take on a different function from the one they usually have during the use of...

  • Page 14

    English 160 12.7.1 description of functions language - language can be selected through the “language” menu . Cup warming plate - by selecting “on”, the cup warming plate is switched on together with the machine. - by selecting “off”, the cup warming plate remains off. Ground dose the quantity of gr...

  • Page 15

    English 161 milk programming the milk quantity programming can be enabled by selecting: - “on” , the button (pr. 12.6) is programmed . - “off” , the button cannot be programmed, and the dose has to be manually adjusted. Hot water mixing while the different types of beverages are brewed, the machine ...

  • Page 16

    English 162 times on/off this function enables to program the automatic switching-on and off times over a whole week. - by selecting “times on/off”, the cursor blinks on the day to be modified. - enter the day, using the button (down), turning the small letter into a capital one. - remove the day fr...

  • Page 17

    English 163 12.10 grind adjustment whatever the coffee blend is, a very fine grinding (notch on low values) increases the density, the cream quantity and the brewing time of the beverage. On the contrary a coarse grinding (notch on high values) decreases the density, the cream, as well as the brewin...

  • Page 18

    English 164 12.11 display messages note - here follows a list of alarm messages (in addition to those explained before) that can be displayed and the relative machine conditions. Standby: the machine is switched off (the main switch is on “i”) and the automatic switching-on/off functions enabled (pr...

  • Page 19

    English 165 13 - routine maintenance warning • in case of troubles, usually indicated on display, switch the machine immediately off, disconnect the power supply through the all-pole switch or by disconnecting the plug, and call the nearest customer service. • before intervening with any type of mai...

  • Page 20

    English 166 13.1.2 brew group (f. 16) cleaning must be carried out with the group empty. • periodically clean the brew group using the special tablets (pr. “12.7.1 explanation of functions – cleaning group”). - remove the brew group (28) pulling the appropriate handle (a) and pressing the button mar...

  • Page 21

    English 167 14 - unscheduled maintenance note- unscheduled maintenance includes every repairing or part replacing. The maintenance technician is the only person authorized to perform these operations. 14.1 jamming of the coffee grinder unit • a foreign body among the coffee beans can cause the grind...

  • Page 22

    English 168 to re-assemble the coffee grinder unit, do as follows: • screw fully the adjustment ring nut (f), then unscrew it by 1/2 turn. This 1/2 turn untightening of ring nut is necessary to avoid grinders jamming and damage. • replace the gearwheel (e) and fix it tightening the screws (d). • rep...

  • Page 23

    English 169 16 - troubles, causes and cures t r o u b l e cause cure the machine does not start display message: “ “ “ “ “ d u m p d u m p d u m p d u m p d u m p b o x b o x b o x b o x b o x f u l l f u l l f u l l f u l l f u l l ” ” ” ” ” grinder error instead of coffee only water is brewed no w...