1. DL manuals
  2. SAGEMCOM
  3. Cordless Telephone
  4. D680C Solo
  5. User Manual

SAGEMCOM D680C Solo User Manual

Other manuals for D680C Solo: User Manual

Summary of D680C Solo

  • Page 1

    User guide d680c solo en mu 25xxxxxx-a_d680c_us.Book page 1 dimanche, 15. Avril 2012 8:52 08.

  • Page 2

    Mu 25xxxxxx-a_d680c_us.Book page 1 lundi, 28. Mai 2012 10:55 10

  • Page 3

    1 you have just bought a d680c and we thank you for your purchase. This product follows a strategy of continuous development. We reserve the right to make changes without notice, modifications and improvements to the products described in this user manual. To operate the device safely and easily, pl...

  • Page 4: Recommendations and

    2 recommendations and safety instructions for safety reasons, never put the handset in the base station without the battery inserted or without the lid on the battery compartment as this could cause an electric shock. To avoid damaging your handset/base, only use certified rechargeable batteries nim...

  • Page 5

    3 in zones where there is a risk of frequent thunder storms, we recommend that you protect your telephone line using an electric power surge protection device. Avoid using the telephone during an electrical storm, there may be a remote risk of electric shock from lightning. Do not attempt to remove ...

  • Page 6: D680C

    4 d680c fcc caution any changes or modifications not expressly approved by the party responsible for compliance could void the user's -authority to operate the equipment. Fcc id: vw3d680c this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: 1 this...

  • Page 7: D680C

    5 d680c • this product complies with fcc radiation exposure limits set forth for an uncontrolled environment. • to comply with fcc rf exposure requirements, the base unit must be installed and operated 20 cm (8 inches) or more between the product and all person's body (excluding extremities of hands...

  • Page 8: D680C

    6 d680c the digits represented by ## are the ren without a decimal point (e.G., 03 is a ren of 0.3). For earlier products, the ren is separately shown on the label.] 5 if this equipment [us: ns3w400bd680c] causes harm to the telephone network, the telephone company will notify you in advance that te...

  • Page 9: D680C

    7 d680c b) the usoc jack required [rj11c] c) facility interface codes ("fic") [xxx] d) service order codes ("soc") [xxx] e) the fcc registration number [us: ns3w400bd680c] if this product is equipped with a corded or cordless handset, it is hearing aid compatible. Fcc id: vw3d680c us: ns3w400bd680c ...

  • Page 10: D680C

    8 d680c contents discover...........................................................11 your phone ......................................................................... 11 unpacking.......................................................................................................................

  • Page 11: D680C

    9 d680c options during a call ........................................................... 34 enable/disable loudspeaker (hands-free mode) .............................................. 34 adjusting volume...................................................................................................

  • Page 12: D680C

    10 d680c handset version ......................................................................................................... 48 resetting the handset............................................................................................... 49 the base ........................................

  • Page 13: D680C

    11 d680c discover... Your phone unpacking open the box and make sure it contains the following items: if you buy a d680c handset you find the following items: discover... 1 un manuel utilisateur un manuel utilisateur un manuel utilisateur un manuel utilisateur un manuel utilisateur un manuel utilisa...

  • Page 14: D680C

    12 d680c discover... Installing the belt clip to install the belt clip: 1 first insert one side of the clip into the dedicated slot (a). 2 gently press on the other side of the clip until the pin snaps into the other slot. The "tic" sound indicates that the belt clip is in the locked position. To re...

  • Page 15: D680C

    13 d680c discover... The handset key description 1. Screen 2. Access to the main menu / validation key. 3. Browser (see "browser" section for details). 4. "answer" key or to get dial tone (short press) / access to " all calls " log (long press). 5. Access to voice mail (long press in standby mode). ...

  • Page 16: D680C

    14 d680c discover... The base caption description 1 indicator light 2 button paging/pairing: • short press: paging of handsets. • long press: pairing of handsets. 3 power socket 4 telephone socket 1 2 3 4 note indicator light operation: - fixed: base startup. - fast flashing: the base is in pairing ...

  • Page 17: D680C

    15 d680c discover... Connecting the base take the base and turn it over. 1 plug the telephone cord into the socket. 2 connect the other end of the cord to the cable gateway. 3 take the power adapter. Connect the power adapter cord to the underside of the base. 4 connect the power adapter to an elect...

  • Page 18: D680C

    16 d680c discover... Browser menu browsing to browse through menus, use the browser keys and the keys , and . Legend item description 1 loudspeaker (switch to hands-free mode)/disable (switch to handset mode). 2 enable/disable the silent mode. 3 select key / main menu access key. 4 phonebook access ...

  • Page 19: D680C

    17 d680c discover... You can go directly to the desired menu by pressing the corresponding sub-menu number (from 1 to 6). D etailed browser example : access to the communication menu during a call: 1 press the options key, the second call is displayed. 2 scroll through the options using the top  or...

  • Page 20: D680C

    18 d680c discover... D etailed browser example : changing the ring tone of external calls 1 press menu (or key). The main menu is displayed on the screen. 2 press the () key then press the () key. 3 enter the melodies menu by pressing the (ok) key. 4 select external ringtone using the  or  key....

  • Page 21: D680C

    19 d680c discover... The screen t he icons displayed in standby mode or during use, your phone screen communicates your phone’s current state through icons, and in particular: legend description 1 status icons: indicates your phone's current state. 2 information field: the current time hh:mm (am /pm...

  • Page 22: D680C

    20 d680c discover... Charging to charge your telephone, place the handset on its charger and make sure the charger is connected to the power supply. The battery charging icon moves to inform you that charging is in progress. The icon display stops moving when the batteries are charged. Statut descri...

  • Page 23: D680C

    21 d680c discover... Handset set-up 1 remove the battery compartment cover on the back of the handset. 2 install the new batteries one by one, noting the polarity of the batteries, and replace the battery cover. 3 the message " sagemcom " is displayed on the screen for a few seconds. 4 the language ...

  • Page 24: D680C

    22 d680c discover... S witch the handset off and then on again to turn off the handset, hold down the red key , the "power off ?" message is displayed on the screen. Press yes to confirm. To turn on your handset, press the red key , the "sagemcom" message is displayed on the screen. Long press long ...

  • Page 25: D680C

    23 d680c discover... Replacing the batteries 1 turn off the handset. Turn it around so that the battery compartment is accessible. 2 remove the battery compartment cover. 3 remove the old batteries, insert the new batteries, noting the polarity of the batteries. 4 replace the battery compartment cov...

  • Page 26: D680C

    24 d680c discover... Menu tree structure phonebook voicemail all calls incoming calls outgoings calls missed calls events tree structure continued on next page options second call intercom calls phonebook selec. Call line mute during a call melodies external ringtone * internal ringtone beeps silent...

  • Page 27: D680C

    25 d680c discover... Settings set handset change code reset base base version set base line name handset list attached hs configuration selec. Call line advanced settings * settings date/time auto hang/pick up language display registration person.Regist base priority handset version reset handset se...

  • Page 28: D680C

    26 d680c call... Managing calls call... 2 note if the handset is being synchronized with the base, the "please wait" message is displayed on the screen. It is not possible to make or receive calls until the "please wait" message has disappeared from the screen. Making a call m ethod 1 (p re - dialin...

  • Page 29: D680C

    27 d680c call... M ethod 2 (p ost - dialing ) call in handset mode 1 press on the green key for 3 or more seconds. 2 dial your contact’s number. Call in speakerphone mode 1 press on the loudspeaker key to speak in speakerphone mode. The icon is displayed on the screen. 2 dial your contact’s number. ...

  • Page 30: D680C

    28 d680c call... Receiving a call 1 t o answer a call press the key or simply pick the handset up from its base if the automatic pick up option is activated. You can also press accept or press key. 2 at the end of the call, press the handset key and put the handset back on its charger. A sound signa...

  • Page 31: D680C

    29 d680c call... Managing several calls your phone allows you to take and manage several calls (subject to service availability) when you are already on a call. Receiving a second call during a call, a beep indicates the arrival of a second call. The contact details of the second caller are displaye...

  • Page 32: D680C

    30 d680c call... Ending one of the calls in progress • during a conversation press options. • choose the option release using the  or  keys. Press ok. The current call is ended and you resume the previous call. Note during the call you can hang up both calls by pressing the key for a long time. A ...

  • Page 33: D680C

    31 d680c call... Making a second call • during a conversation press options. • choose the option second call using the  or  keys. Press ok. • select the number for the person you want to call in the address book by pressing , and then ok. - or - • dial the number using the keypad and select. • the...

  • Page 34: D680C

    32 d680c call... Transferring calls during a call, you can transfer it to another handset. This function can be used as long as two handsets have been registered to the same base. • during a conversation press options. • choose the option intercom. Press ok. U nannounced transfer this function allow...

  • Page 35: D680C

    33 d680c call... A nnounced transfer this function allows you to transfer the current call to another device once it has been picked up . Steps calling handset called handset 1 press ok. 2 select the handset (or all handsets) to call. 3 press ok. 4 rings: internal call. 5 press the key to accept the...

  • Page 36: D680C

    34 d680c call... Options during a call you can use the following options during a call: enable/disable loudspeaker (hands-free mode) h andset loudspeaker during the call you can activate the hands-free mode by pressing the key. The icon is displayed on the screen. To disable the hands-free mode, pre...

  • Page 37: D680C

    35 d680c call... Enable the mute mode during a call, you can switch to mute mode and your handset's microphone will be muted and your contact will no longer hear you. To enable the mute mode : • during a conversation, press options . • select mute, press select . The icon is displayed at the top of ...

  • Page 38: D680C

    36 d680c call... Using additional handsets you can associate additional handsets with your phone. You can then make and receive outside calls or calls between these handsets. Note y ou first have to pair the handsets with the base. For further details, refer to the section “associating a new handset...

  • Page 39: D680C

    37 d680c manage your contacts... Use the phonebook manage your contacts... 3 your phonebook is common to all the dect handsets paired to the same base. You can also directly access the list of phonebook entries using the key. When browsing through the phonebook, the handset displays the number of th...

  • Page 40: D680C

    38 d680c manage your contacts... Call a contact from the phonebook • press menu . • select phonebook, press ok. • select an entry using list or search and press ok. • select call and press ok. Changing an entry • press menu . • select phonebook, press ok. • select an entry using list or search and p...

  • Page 41: D680C

    39 d680c manage your contacts... Delete all the entries • press menu . • select phonebook, press ok. • select delete all using the or  keys. Press ok. • for the question delete all?, press ok to confirm the deletion of all entries. Warning this operation will erase all the files in your base. Onc...

  • Page 42: D680C

    40 d680c voicemail service voicemail service 4 warning you should not change the voicemail number unless instructed by your phone service provider. Note the default voice mail number is *99. Modifying the voicemail number this function allows you to change your voicemail number. Unanswered calls are...

  • Page 43: D680C

    41 d680c audio adjustment... Audio adjustment... 5 changing the ringtone you can change the ring of: - outside calls, - calls between handsets (intercom). • press menu . • select melodies, press ok. • select external ringtone to change the ringing tone for external calls. - or - • select internal ri...

  • Page 44: D680C

    42 d680c audio adjustment... Enabling/disabling audio alerts audio alerts refer to: • pressing the keypad keys, • putting the handset on the charger, • low battery alert, • others (error alerts). • press menu . • select melodies, press ok. • select beeps to change the audio alerts, then press ok. • ...

  • Page 45: D680C

    43 d680c setting up... The phone setting up... 6 setting the date and the time • press menu . • select settings, press ok. • select settings using the  or  keys and press ok. • select date/time using the  or  keys and press ok. • the date and time setting screen is displayed, press edit . • set ...

  • Page 46: D680C

    44 d680c setting up... Picking up and hanging up calls automatically this function allows you to take and end a call by simply taking the handset off or placing it back on its charger. • press menu . • select settings, press ok. • select settings using the  or  keys and press ok. • select auto han...

  • Page 47: D680C

    45 d680c setting up... Adjust the brightness • press menu . • select settings, press ok. • select settings using the  or  keys and press ok. • select display using the  or  keys and press ok. • select brightness using the  or  keys and press ok. • a bar graph is used to adjust the brightness a...

  • Page 48: D680C

    46 d680c setting up... The handset associating a new handset the base allows you to pair additional handsets so that they are recognized. F rom the base : to enable the pairing mode, press and hold (on the bottom of the base). F rom the handset : case 1: the handset displays "please register". • pre...

  • Page 49: D680C

    47 d680c setting up... Customizing the handset’s registration this function allows you to pair your handset with a phone base (if you have more than one phone base). • press menu . • select settings, press ok. • select advanced settings using the  or  keys and press ok. • select set handset using ...

  • Page 50: D680C

    48 d680c setting up... Defining the main base for your handset this function allows you to specify the priority base to be used for making calls. • press menu . • select settings, press ok. • select advanced settings using the  or  keys and press ok. • select set handset using the  or  keys and ...

  • Page 51: D680C

    49 d680c setting up... Resetting the handset when you reset your handset, all the settings are returned to their initial values (factory settings), except for the phonebook. • press menu . • select settings, press ok. • select advanced settings using the  or  keys and press ok. • select set handse...

  • Page 52: D680C

    50 d680c setting up... The base changing the base code the base code (pin number) is 0000 by default, but can be changed to 4 other numbers. You will be prompted to enter it, when registering a new handset. • press menu . • select settings, press ok. • select advanced settings using the  or  keys ...

  • Page 53: D680C

    51 d680c setting up... Base version • press menu . • select settings, press ok. • select advanced settings using the  or  keys and press ok. • select set base using the  or  keys and press ok. • select base version using the  or  keys and press ok. • the following information is displayed: - b...

  • Page 54: D680C

    52 d680c setting up... The line this menu allows you to change the settings of the lines on the base. Important we do not recommend that you change line settings without first contacting your operator, as this may result in your phone line being disconnected. Change the line name • press menu . • se...

  • Page 55: D680C

    53 d680c setting up... Allow three-way communication (intrusion) this intrusion function allows or prohibits a second handset registered on the same base to share an ongoing conversation. If the intrusion mode is enabled, you will then be able to share a call in progress with another handset. • pres...

  • Page 56: D680C

    54 d680c setting up... Call management this menu allows you to select the line on which you want to make your first outgoing call. Managing your calls • press menu . • select settings, press ok. • select advanced settings using the  or  keys and press ok. • select selec. Call line using the  or ...

  • Page 57: D680C

    55 d680c setting up... The list of handsets this menu displays the list of handsets registered on the same base. Manage handsets • press menu . • select settings, press ok. • select advanced settings using the  or  keys and press ok. • select handset list using the  or  keys and press ok. • the ...

  • Page 58: D680C

    56 d680c accessories... The alarm accessories... 7 note the alarm clock function arranges your handset to ring each day at a specified time. Once a time is programmed, the selected ringtone rings for 60 seconds through the handset’s loudspeaker and a warning screen is displayed. To stop the warning,...

  • Page 59: D680C

    57 d680c accessories... The timer note the timer function enables the handset to ring after a programmed time. You can view the time countdown in minutes on the screen. Program the timer • press menu . • select accessories, press ok. • select timer using the  or keysand press ok. • the timer set...

  • Page 60: D680C

    58 d680c tracking your calls... Call logs logs are lists of numbers or events received or sent by your phone. Depending on your phone company and the options of your contract, the following information may be accessed in the call logs: • the date and time of the call. • the contact's name and/or num...

  • Page 61: D680C

    59 d680c tracking your calls... Viewing the received or dialed call log • press menu . • select calls, press ok. • select incoming calls, (or outgoings calls) using  or  keys then press ok. • the last received call (or dialed number) is then displayed. • the other calls are displayed using the key...

  • Page 62: D680C

    60 d680c tracking your calls... Consulting the missed call log the icon is displayed if there are one or more new missed call which have not been reviewed yet. • press menu . • select calls, press ok. • select missed calls using the  or  keys, then press ok. • the latest missed call is displayed. ...

  • Page 63: D680C

    61 d680c tracking your calls... Managing incoming or outgoing calls • press menu . • select calls, press ok. • select all calls or outgoings calls or incoming calls or missed calls then press ok. • the list of calls (incoming/outgoing/missed) is displayed. • select the desired call and press ok, to ...

  • Page 64: D680C

    62 d680c tracking your calls... The events log note the icon is displayed if there is one or more voicemail messages. Checking new events a summary screen for the number of events that occurred in your absence is displayed: - number of missed calls, - operator messages. • press ok. • select events t...

  • Page 65: D680C

    63 d680c appendix appendix care and maintenance turn off the device and remove it from the power supply before cleaning the surface. Use a soft, lint-free cloth. Never user liquid, gaseous or easily flammable cleansers (sprays, abrasives, polishers, alcohol). Do not allow any moisture to reach the i...

  • Page 66: D680C

    64 d680c appendix care instructions for the battery the capacity of the battery diminishes with time. You can prolong the life of the battery if you observe the following points : • use the device at least once a week. • charge the battery regularly. Don’t store the device with a completely discharg...

  • Page 67: D680C

    65 d680c environment environment environmental protection and sustainable development is an important priority for sagemcom. Sagemcom has a policy of using environmentally- friendly systems and makes environmental protection an essential part of the life-cycle of its products – from the manufacturin...

  • Page 68: D680C

    66 d680c guarantee guarantee limited warranty what does this limited warranty cover? Sagemcom warrants to the holder of a valid proof of purchase (“consumer” or “you”) that the product and all accessories provided in the sales package (“product”) are free from defects in material and workmanship, pu...

  • Page 69: D680C

    67 d680c guarantee what is not covered by this limited warranty? This limited warranty does not cover: 1 product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid int...

  • Page 70: D680C

    68 d680c guarantee what must you return with the product to get warranty service? 1 return the entire original package and contents including the product to the sagemcom's authorized service representative location along with a description of the malfunction or difficulty; and 2 include a “valid pro...

  • Page 71: D680C

    69 d680c guarantee • reorient or relocate the receiving antenna. • increase the separation between the equipment and receiver. • connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • consult the dealer or an experienced radio/tv technician for he...

  • Page 72: Sagemcom Broadband Sas

    Sagemcom broadband sas 250, route de l'empereur - 92848 rueil-malmaison - france tél. +33(0)1 57 61 10 00 - fax : +33(0)1 57 61 10 01 www.Sagemcom.Com 25 354 6047 d - 0 5 /14 mu 25xxxxxx-a_d680c_us.Book page 2 lundi, 28. Mai 2012 10:55 10