Salicru SLC TWIN PRO Series User Manual - General Index
3
SALICRU
General index
1.
Introduction.
1.1. Acknowledgement letter.
1.2. Using this manual.
1.2.1. Conventions and used symbols.
1.2.2. For more information and/or help.
1.2.3. Safety instructions.
1.2.3.1. General safety warnings.
1.2.3.2. To keep in mind.
1.2.3.3. Safety warning regarding batteries.
2.
Quality and standard guarantee.
2.1. Declaration of the management.
2.2. Standard.
2.3. Environment.
3. Presentation.
3.1. Views.
3.1.1. Views of the equipment.
3.2. Definition of the product.
3.2.1. Nomenclature.
3.3. Operating principle.
3.3.1. Main features.
3.4. Options.
3.4.1. Isolation transformer.
3.4.2. External maintenance manual bypass.
3.4.3. Integration in IT networks by means of the SNMP adaptor.
3.4.4. Relays interface card.
3.4.5. Parallel cable.
3.4.6. MODBUS protocol.
4. Installation.
4.1. To be considered in the installation.
4.2. Reception of the equipment.
4.2.1. Unpacking, content checking and inspection.
4.2.2. Storage.
4.2.3. Unpacking.
4.2.4. Transport to location.
4.3. Connection.
4.3.1. Connection of input power block.
4.3.2. Connection of bypass power block. TWIN/3 PRO > 10 kVA only.
4.3.3. Connection to output power block.
4.3.4. Connection of external batteries (extended back up times).
4.3.5. Connection of main input earth terminal
(
)
and the earth bonding
terminal
(
)
.
4.3.6. Terminals for EPO (Emergency Power Off).
4.3.7. Connection in parallel.
4.3.7.1. Introduction to the redundancy.
4.3.7.2. Installation and parallel operating.
4.3.8. Communication ports.
4.3.8.1. RS232 and USB interfaces.
4.3.8.2. Smart slot.
4.3.8.3. Relays interface (option).
4.3.9. Software.
4.3.10. Considerations before starting up the connected loads.
5. Operating.
5.1. Commissioning.
5.1.1. Controls before commissioning.
5.2. Start up and shutdown of the UPS.
5.2.1. Start up of the UPS, with mains present.
5.2.2. Start up of the UPS, without mains.
5.2.3. UPS shutdown, with mains present.
5.2.4. UPS shutdown, without mains.
5.3. Operative for a parallel system.
5.4. How to integrate a new UPS in an operating parallel
system.
5.5. How to replace a faulty UPS from the operating parallel
system.
5.6. Manual Bypass Switch (maintenance).
5.6.1. Operating principle.
5.6.2. Transference to maintenance bypass.
5.6.3. Transference to normal mode.
6.
Control panel with LCD.
6.1. Control panel.
6.1.1. Functionality of the LEDs.
6.1.2. Acoustic alarms.
6.1.3. UPS status and color LCD display, as condition.
6.1.4. Main screen.
6.2. Operating modes of the equipment.
6.3. Operating of the LCD panel.
6.3.1. Main screen.
6.3.2. UPS status submenu.
6.3.3. Data logger submenu.
6.3.4. Measurement submenu.
6.3.5. Control submenu.
6.3.6. Identification submenu.
6.3.7. Setting submenu.
6.4. Special functions
6.4.1. Operating on ECO mode.
6.4.1.1. Short description of the ECO mode.
6.4.1.2. To establish the ECO mode function.
6.5. Operating as frequency converter.
6.5.1.1. Short description of the frequency converter function.
6.5.1.2. To establish the Converter mode function.
7.
Maintenance, warranty and service.
7.1. Battery maintenance.
7.1.1. Notes for installing and replacing the batteries.
7.2. UPS Trouble Shooting guide.
7.2.1. Troubleshooting guide. Warning indications.
7.2.2. Troubleshooting guide. Fault indications.
7.2.3. Troubleshooting guide. Other circumstances.
7.3. Warranty conditions.
7.3.1. Covered product.
7.3.2. Warranty terms.
7.3.3. Out of scope of supply.
7.4. Description of the available maintenance and service
contracts.
7.5. Technical service network.
8. Annexes.
8.1. General technical specifications.
8.2. Glossary.