Salus OPTIMA ZigBee User Manual

Other manuals for OPTIMA ZigBee: Quick Start Manual

Summary of OPTIMA ZigBee

  • Page 1

    ' version'1.0' salus controls inc. 123 townsend st. Level ll2 san francisco, ca 94107 for other language versions, please visit: www.Salusinc.Com optima'zigbee'thermostat' ' user'manual'.

  • Page 2

    Ii ' salus user' manual' s afety' i nstructions ' please read these instructions carefully before installing and using the optima thermostat, and keep this guide in a safe place for future reference. • follow all local and electricity supplier regulations regarding the installation or replacement of...

  • Page 3

    32 ' salus user' manual' a ppendix' b ' – ' r egulatory' s tatements ' fcc'statements' warning: changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the fcc ...

  • Page 4

    Iv ' salus user' manual' c ontents ' in#the#box# 1 ! Controls#and#display# 2 ! B uttons ! 2 ! H ome! S creen ! 4 ! Installing#the#thermostat# 6 ! T ools ! 7 ! T urn!Off!Power!To! Hvac !System ! 7 ! D etermine!Wiring!Configuration ! 7 ! R emove! O ld! T hermostat ! 9 ! I nstall! M ounting! P late ! 9...

  • Page 5

    30 ' salus user' manual' single'transformer'heat'pump'system' optima'zigbee'thermostat' v ' ' using#the#thermostat# 13 ! C hanging!The! S et! P oint! T emperature ! 13 ! S etting!A! Hold ! S et! P oint! T emperature ! 14 ! C hanging!The! O perating! M ode ! 15 ! T urning! O n!The! F an ! 15 ! Config...

  • Page 6

    Vi ' salus user' manual' f loor! H eating! S ystem ! 29 ! S ingle! T ransformer! H eat! P ump! S ystem ! 30 ! T wo! T ransformer! H eat! P ump! S ystem ! 31 ! Appendix#b#–#regulatory#statements# 32 ! Fcc ! S tatements ! 32 ! Fcc !And! I ndustry! C anada ! 33 ! I ndustry! C anada ! 33 ! ' optima'zigb...

  • Page 7

    28 ' salus user' manual' conventional'two'transformer'heat'and'cool'system' optima'zigbee'thermostat' 1 ' ' i n'the' b ox ' thermostat with mounting plate trim plate screws and anchors wire labels 2 x aa alkaline batteries user’s manual quick start guide.

  • Page 8

    2 ' salus user' manual' c ontrols'and' d isplay ' buttons' slider ring + /next –/previous fan/hold /back mode /enter reset (on bottom of unit) optima'zigbee'thermostat' 27 ' ' conventional'single'transformer'heat'and'cool'system'.

  • Page 9

    26 ' salus user' manual' a ppendix' a ' – ' w iring' d iagrams ' terminal'definitions' optima'zigbee'thermostat' 3 ' ' button regular mode installation mode slider ring slide clockwise to increment or counter- clockwise to decrement values. Display next/previous option. –/previous tap to decrement v...

  • Page 10

    4 ' salus user' manual' home'screen' the home screen is the main display screen. If you do not press any buttons for 3 seconds, the thermostat will return to the home screen. System mode fan mode set point temperature room temperature day of week & time radio icon low battery heat and cool icons lab...

  • Page 11

    24 ' salus user' manual' s alus' w arranty ' salus controls inc. (“salus”) warrants that for a period of two (2) years (“warranty period”) from the date of purchase by the consumer (“customer”), this device, excluding batteries (“product”), shall be free of defects in materials and workmanship under...

  • Page 12

    6 ' salus user' manual' indicator meaning system mode operating mode for the hvac / heat pump system off – system is off cool – ac or cooling mode heat – furnace or heating mode emheat – emergency heat mode (heat pump only) fan mode manual fan override auto – fan based on heat / cool activity on – f...

  • Page 13

    22 ' salus user' manual' s pecifications temperature units °c or °f operating temperature 32-113 °f (0-45 °c) indoor temperature measurement range 32-99 °f (0-37 °c) rf frequency 2.40-2.48 ghz rf range up to 1300 ft (400 m) line of sight protocol zigbee – home automation 1.2 battery power 2 x aa alk...

  • Page 14

    8 ' salus user' manual' when replacing an existing thermostat, the goal is to replicate the wiring of the old thermostat on the optima thermostat. • remove the old thermostat to expose the wiring terminals. • take a picture of the wiring for future reference. • note the terminals attached to each wi...

  • Page 15

    20 ' salus user' manual' pairing process. Check with your connected home system procedures for more details. • prepare connected home system to add a thermostat. • go to the pair menu item on the optima thermostat. • press mode to select pairing mode. Display will show' will pair. • press mode again...

  • Page 16

    10 ' salus user' manual' attach'wiring' before attaching the wires, match the wire (using the labels) to its corresponding terminal. Refer to the picture of the wiring taken earlier if necessary. • open the terminal by lifting the latch up. • push each wire into the hole of the terminal and push the...

  • Page 17

    18 ' salus user' manual' daylight savings time on – daylight savings time is observed (default) off – daylight savings time is not observed settings country – sets operating limits and defaults for time zone and temperature units us – united states values ca – canadian values hvac type hp – heat pum...

  • Page 18

    12 ' salus user' manual' attach'thermostat'to'mounting'plate' attach the thermostat to the mounting plate by aligning the connector pins and the plastic retention posts and pushing the thermostat onto the mounting plate. Make sure the connector pins are not bent and that the thermostat is fully seat...

  • Page 19

    16 ' salus user' manual' the fan mode will change to indicate the current mode of the fan, and the fan icon will appear when the fan is turned on. There will be a slight delay between selecting fan on mode and the fan turning on. Press the fan/hold button again to put the fan back into auto mode, un...

  • Page 20

    14 ' salus user' manual' sliding your finger along any part of the slider ring (the silver circular ring around the screen) other than the mode and fan/hold locations will also change the set point temperature. To increase the set point, slide clockwise on the circular ring. To decrease the set poin...