Operators manual 52k650z.
Encore 1 your mower is only as safe as the operator! Operator carelessness or error may result in serious bodily injury. Improper maintenance of the machine may also result in injury. Please read and follow these instructions on safe operation and be certain that anyone using this mower fully unders...
Encore 2 assembly instructions for 42b350z ; 42k450z ; 48b450z ; 48k550z ; 52b550z ; 52k650z. Remove unit from crate, taking care to re- move inner boxes and the small parts box. 1. Remove deflector chute, bolt bag and operator’s manual from main assembly. 2. Open bolt bag and lay out bolts: (8) – 5...
Encore 3 4. Take the 4 – 5/16 x 3/4 hhcs and 4 – lock washers and fasten seat to the seat plate. 5. Take the remaining bolts and whizlocks nuts and bolt control levers onto the outsides of the mount angles, adjusting them according to operator comfort. 6. Attach the wire harness to the seat switch. ...
Encore 4 warning: the engine exhaust from this product contains chemicals known in the state of california to cause cancer, birth defects or other reproductive harms. Mowing speed the encore rider is designed to operate most efficiently at maximum blade speeds. The running speed of the machine shoul...
Encore 5 follow the installation instructions printed on the filter. Use only a high quality 20w50 rated engine oil. Note: refer to the engine manual for engine lubrication recommen- dations. Oil and filter for 42k17z ; 48k19z ; 52k21z. Change the hydraulic system filter at 250 hours. The hydraulic ...
Encore 6 belt adjustment remove key from the ignition switch. The deck drive belt, which may be accessed by removing the deck plate, (see fig.1) has a turnbuckle assembly to adjust spring tension. Spring tension should be maintained at 4" of spring stretch measuring the spring coils. By turning the ...
Encore 7 neutral adjustment - drive 1. Raise the rear wheels of the rider off of the ground. Safely block the frame in this posi- tion so it is secure. 2. With the operator in the seat, start and run the engine, leaving the control levers in the neutral position. Release the park brake. Check the re...
Encore 8 to test drive operations: check air pressure in tires. Equal tire pressure is critical for proper drive opeation. check linkage for excessive play. • raise rear of rider until rear wheels are off the ground. Safely block the frame in this position. • put control levers in neutral lock p...
Encore 9 warning: never run the engine if the bat- tery is removed or if the battery is not connected to the charging system. Serious damage to charging system components may result. Deck leveling adjustment before checking the deck level makes sure that tire pressures are inflated to the proper lev...
Encore 10 42b350z , 48b450z , 52b550z 423078 wire harness electrical drawing ground to engine to batt. Ground to batt. Pos. Black 18 ga. Black 14 ga. Red /black stp. 18 ga. Yellow 16 ga. Yellow 16 ga. Red 14 ga. Green 18 ga. Green 18 ga. Green 18 ga. Purple 18 ga. Orange 18 ga. Dk. Blue 18 ga. White...
Encore 11 starter relay 15 amp fuse 20 amp fuse red 14 ga. Lt. Blue 14 ga. Brown 18 ga. Black 16 ga. Green 18 ga. Park brake switch wire junction red 12 ga. Black / white 18 ga. Dk. Blue 18 ga. Engine kill red /black stp. 18 ga. To batt. Pos. Orange 18 ga. Engine charging engine fuel solenoid to bat...
Encore 12 red 14 ga. Starter relay black 16 ga. Brown 18 ga. Lt. Blue 14 ga. Park brake switch red 12 ga. Engine fuel solenoid engine charging orange 18 ga. To batt. Pos. Red /black stp. 18 ga. Engine kill dk. Blue 18 ga. Black 16 ga. T o batt. Ground 20 amp fuse 15 amp fuse wire junction 42k17z , 4...
Encore 13 bdp-10l variable pump – support system transmission hydraulic support system the charge pump incorporated into the bdp- 10l units supplies fluid to keep the closed loop charged, preventing cavitations and providing cooling oil flow for the system. An inlet filter is required to insure that...
Encore 14 controls and features - bdp-10l variable pump direct displacement control the direct-proportional displacement control (ddc) provides a simple method of control. Movement of the swashplate control shaft produces a proportional swashplate movement and change in pump flow and/or direction. I...
Encore 15 start up maintenace - bdp-10l variable pump fluids fluids used with hydro-gear product should be carefully selected with assistance from a reputable supplier. Typically, an api classification sg/cd engine oil is used with a viscosity range equivalent to 20w50. Start-up procedure the follow...
Encore 16 maintenance check the reservoir daily for proper fluid level, the presence of water (noted by a cloudy to milky appearance, or free water in bottom of reservoir), and rancid fluid odor (indicating excessive heat). The bdp-10l units normally do not require regular fluid changes. The system ...
Notes:.
Encore warranty for prowler and z series mowers (excluding the z 34) this warranty extends to the original retail purchaser only and commences on the date of original retail purchase. Any part of the encore commercial mower manufactured by encore mfg. Co., inc. And found in reasonable judgment of en...
,encore manufacturing co., inc. All rights reserved. Contents subject to change. P art n umber 1102 a z series 52k650z - operators manual 933077.