Smart Temp 42-159 Installation And Operation Manual - page 10
42-159 Aug-10-2011
Planning your program
Note:
The time of day clock MUST be set to the correct day and time in order for
the programmed times to be correct.
Look at the factory preprogrammed times and temperatures shown in the Factory
default program setting. If this program will suit your needs, simply press the RUN
button to begin running the factory preset program.
If you wish to change the preprogrammed time and temperature, follow these
steps:
Determine the time periods and temperatures for your program. You must
program four periods for each day. However, you may use the same heating and
cooling temperatures for consecutive time periods. You can choose heating
temperature, cooling temperature and start time independently. (for example, you
may select 5:00 am AND 70º F as the weekday 1
st
period heating start time and
temperature and also choose 7:00 AM and 76º F as the weekday 1
st
period
cooling start time and temperature.
Use the table below to plan your program time periods and the temperatures you
want during each period. Fill in the completed table to have a record of your
program.
EXAMPLE:
Heating/Cooling Schedule Plan (Factory default program setting)
Weekdays
(5 day)
Saturday
and
Sunday
Mode Period Start
Time Temperature Start
Time Temperature
Heat 1
st
6:00
AM 21.0ºC 6:00
AM 21.0ºC
2
nd
8:00
AM 16.5ºC 8:00
AM 16.5ºC
3
rd
6:00 PM
21.0ºC
6:00 PM
21.0ºC
4
th
10:00 PM
16.5ºC
10:00 PM
16.5ºC
COOL 1
st
6:00
AM 24.0ºC 6:00
AM 24.0ºC
2
nd
8:00
AM 28.0ºC 8:00
AM 28.0ºC
3
rd
6:00 PM
24.0ºC
6:00 PM
24.0ºC
4
th
10:00 PM
25.5ºC
10:00 PM
25.5ºC
-10-
Heating/Cooling Schedule Plan
Weekdays
(5 day)
Saturday
and
Sunday
Mode Period Start
Time Temperature Start
Time Temperature
Heat 1
st
2
nd
3
rd
4
th
COOL 1
st
2
nd
3
rd
4
th
Enter the Heating Program
1) Move the
SYSTEM
switch to the
HEAT
position.
2) Press
PRGM
once.
PRGM SETTING
will display, and “MON TUE WED THU
FRI” (indicating weekday program) will appear in the display (flashing). Also
displayed are the current programmed start time for the 1
st
heating period
(flashing),and the currently programmed temperature.
3) Press the
▲
and
▼
buttons to select the desired 1
st
heating period start time.
The time will change in 15 minute increments. When your selected time is
displayed, press the
TIME
button to change to the temperature mode.
4) Press the
▲
and
▼
buttons to select the desired 1
st
heating period
temperature.
5) Press
PRGM
once. The currently programmed start time and set point for the
2
nd
heating program will appear.
6) Repeat steps 3 and 4 to select the start time and heating temperature for the
2
nd
heating program period.
7) Repeat steps 3 thru 5 for the 3
rd
and 4
th
heating program periods.
8) Press
PRGM
once.
PRGM SETTING
will display, and “SAT SUN”
indicating weekday program) will appear in the display (flashing). Also
displayed are the current programmed start time for the 1
st
heating period
(flashing),and the currently programmed temperature.
9) Repeat steps 3 thru 7 to complete Saturday and Sunday programming.
10) When you have completed entering your heating program, press
RUN
.
-11-