Smarthome 12063W Quick Referenc Manual - page 5
Helpful Tools
If you’re investing in home automation, there are a few tools that will make your
projects run smoother:
Invest in a Maxi-Controller
This plug-in transmitter has the ability to send individual X10
commands. The buttons are separated into Addresses and
Command functions. To use this controller, you have to press the
address (for example, “5”), then the command (ON, OFF, BRIGHT,
etc.). Some of the KeypadLinc’s features need to be programmed
with individual button-presses in order to set certain features. For
more info visit: http://www.smarthome.com/4020.html.
X10 Signal Meter
This is an invaluable tool when it comes to installing
and diagnosing problems. By knowing the signal
strength at a specific location, you can make sure that
the signal will always trigger that X10 module.
Generally, it’s ideal to have at least 100mV at each
location. Conservative installers will want even more;
perhaps 250mV just in case the homeowner installs a
new big-screen TV after final installation. The extra
margin will still give the X10 receivers enough signal
to be reliably triggered. These units can also be used
to measure the effects of signal absorption mentioned
earlier. Plug in the transmitter and measure the signal, then unplug the device that’s
plugged into that outlet. If you see a 10% or greater change, use a filter on that
device. Smarthome has three units to choose from:
www.smarthome.com/4814.html
www.smarthome.com/4811.html
www.smarthome.com/4813.html
Custom Keypad Labels
Your KeypadLinc has been shipped with labels that you can use to customize your
keypad. You can use the pre-printed labels that shipped with your KeypadLinc or
you can create your own using the enclosed blank labels.
While we encourage you to customize your KeypadLinc, please be gentle in
removing the keys. The buttons on the KeypadLinc 8 require special care in
removing the keycaps. Using a small, flat edged screwdriver, ONLY pry up on the
sides of the keys from the middle of the keypad (as shown below). Make sure you
are centered on the key as there is a small "lip" to pull up on located there. Should
any damage occur to you KeypadLinc during the labeling, please contact
Smarthome Customer Service at 1-800-762-7846
and we will be happy to replace your unit.
Step-by-step Instructions
1. Disconnect the power for the existing switches at the circuit breaker or fuse
panel. Verify that the power has been removed by trying to turn on the lights
controlled by the switches.
2. Remove the trim plate from the existing switches.
3. Unscrew and pull the existing switches from the wall box.
4. Disconnect the wires from the existing switches.
5. If the KeypadLinc is being installed into a 3/4/5-way
circuit, the SwitchLinc Multi-way Companion Switch
must be installed in the wall box where power comes
into the circuit. Follow the instructions included with
the Multi-way Companion Switch to identify the "Hot,"
"Neutral," "Ground," and "Traveler" wires.
6. Before making any connections to the KeypadLinc, gently pull its Status LED/
Set Button until a click is heard. This will open the "air gap" and isolate the
KeypadLinc from the electricity when the circuit breaker is turned back on.
7. Orient KeypadLinc so the LED is at the top, and make the connections
according to the "KeypadLinc Wiring Diagram" below.
8. After all connections have been made, ensure that all wire connectors are
firmly attached and that there is no exposed copper except for the Ground
wire.
9. Gently place the wires and the KeypadLinc into the wall box (with LED at top
of device) and screw into place.
10. Before installing the faceplates, restore power to the circuit, and press in the
KeypadLinc’s Status LED/ Set Button top until it is even with the front plastic
trim ring. Once the Set Button is pressed in, power will be supplied to the
KeypadLinc. After a few seconds, the green Status LED will come on.
11. After testing KeypadLinc for proper operation, install the faceplate (sold
separately).
Tip:
For additional help
installing 3-way circuits,
see page 5 in the Multi-
way Companion Switch
manual.
5
20
Download a template to make
your own labels at:
http://www.smarthome.com/
manuals/12063_template.doc
#4020 Maxi-
Controller
#4814 X10
Signal Analyzer