W w w . S m a r t p o o l . C o m smartpool robotic pool cleaner repair manual.
2 nc71au cleaner parts a a a 22 admiral ultra (nc71au) location product # description 1 nc7115 top shell 2 nc7106 lower chassis 3 nc7122au power supply 4 nc7123 cable 5 nc7107 drive motor 6 nc7113 pump motor 7 nc1004 drive brush 8 nc7108 drive wheel tube 9 nc7112 non drive wheel tube 10 nc7104 brush...
3 nc32au & nc52au cleaner parts admiral (nc32au) admiral plus (nc52au) location product # product # description 1 nc1001:02 chassis 2 and 2a nc1009:02 nc1024:02 pump motor 3 and 3a nc1013au nc1023au power supply 4 nc1012:02 floating cord 5 nc1006:02 drive motor 6 nc1010 drive tube mount 7 nc1011 cha...
4 ra: received: service center location: customer: phone: email: date of purchase: y n partial authorized by: serial number: used misuse ------------ ------------ water entry motor programming other: part # qty part # qty nc7102 non drive wheel tube nc7112 nc7103 pump motor nc7113 nc7104 top return ...
5 ra: received: service center location: customer: phone: email: date of purchase: y n partial authorized by: serial number: used misuse ------------ ------------ water entry motor programming other: part # qty part # qty nc1001:02 foam ring nc1014 nc1003 impeller nc1015 nc1004 bottom lid nc1016 dri...
6 nc71au troubleshooting guide model: scrubber/admiral ultra test cable (26-29vdc) test power supply (29-32vdc) replace drive motor replace cable replace pump motor remove any debris from impeller or tracks and check for damage. Test drive motor with test cable (ok) replace power supply water test (...
7 smartpool robotic cleaner troubleshooting guide models: nitro/admiral/admiral plus test cable (25-28vdc) test power supply (28-32vdc) self test (ok) filter bag properly installed replace power supply water test (ok) replace cable return to customer test pump motor (25-28vdc) replace pump motor tes...
W w w . S m a r t p o o l . C o m 8 scrubber series evaluation model number: nc71au.
W w w . S m a r t p o o l . C o m 9 1) place the cleaner on the bench and examine for physical damage and for any debris caught in the impeller or drive brushes (remove debris if found). 2) place the cleaner upside down on bench and remove the bottom lid by pushing in on the red tabs. 3) perform a s...
W w w . S m a r t p o o l . C o m 10 • if the cleaner is “dead in water” or has “no suction/does not pick up debris” then the unit should not move at all during the self test. • if the cleaner is “spinning in circles” or “does not move” then the impeller should operate during the self test. Results.
W w w . S m a r t p o o l . C o m 11 test the power supply nc7122au.
W w w . S m a r t p o o l . C o m 12 4) test the voltage through the power supply: insert the prongs of the voltmeter into the (2) copper plugs of the power supply socket and turning the unit to the on position (29-32vdc). Picture does not reflect new style power supply design but voltage output is ...
W w w . S m a r t p o o l . C o m 13 test the cable nc7123.
W w w . S m a r t p o o l . C o m 14 6) place the prongs of meter into the back of the cable harness, connect the other end of the cable to the power supply and turn the power supply to the on position. Important: leave the cable plugged into the pump motor for an accurate reading. • if the voltage ...
W w w . S m a r t p o o l . C o m 15 test the drive motor nc7107.
W w w . S m a r t p o o l . C o m 16 8) carefully remove the heat shrink covering the drive motor connection. 9) connect one end of the test cable to the drive motor and the other end to the power supply. Turn the power supply to the on position. Important: this is a quick on/off test. Do not run th...
W w w . S m a r t p o o l . C o m 17 replacing the cable nc7123.
W w w . S m a r t p o o l . C o m 18 1) loosen the pressure fitting to the cable and gently pull on the wires to expose the connection. 2) carefully remove the heat shrink covering the drive motor connection. 3) remove the (2) screws that hold the strain relief to the shell of the cleaner..
W w w . S m a r t p o o l . C o m 19 4) pull up on the cable to gain access to the strain relief. 5) remove the (2) screws that hold the two halves of the strain relief together. 6) remove the defective cable from the cleaner and feed the new cable through the shell..
W w w . S m a r t p o o l . C o m 20 note: there should be at least 14’’ (~35cm) of cable inside the cleaner: that is the distance from the strain relief to the pump motor. 7) find the 14’’ (~35cm) mark and make a loop in the cable that intersects with that line. 8) take that loop and fold/rotate it...
W w w . S m a r t p o o l . C o m 21 steps 7 and 8 9) insert the looped cable into the strain relief. 10) reinstall the (2) screws that hold the two halves of the strain relief together..
W w w . S m a r t p o o l . C o m 22 11) pull the cable from the back of cleaner so that the strain relief is resting against the shell. 12) reinstall the (2) screws that hold the strain relief to the shell of the cleaner by aligning the threads of the cable collar. 13) reconnect the cable harness (...
W w w . S m a r t p o o l . C o m 23 replacing the drive motor nc7107.
W w w . S m a r t p o o l . C o m 24 1) loosen the pressure fitting to the drive motor and gently pull on the wires to expose the connection. 2) carefully remove the heat shrink covering the drive motor connection. 3) remove the tracks by gently pulling outward on the track while rotating the drive ...
W w w . S m a r t p o o l . C o m 25 4) with a phillips head screwdriver, remove the (5) screws from each side-plate . 5) remove both side-plates. 6) remove the (2) drive pulleys on the drive motor side using a phillips head screwdriver..
W w w . S m a r t p o o l . C o m 26 7) remove the (3) motor mount screws using a phillips head screwdriver on the drive motor side. 8) gently pull on the drive motor to remove it from the shell and slide the drive tubes from the drive motor. 9) pull the cable to the drive motor through the hole in ...
W w w . S m a r t p o o l . C o m 27 the cleaner is fully disassembled and ready to be reassembled with the new drive motor. 10) feed the cable of the new drive motor through the hole in the shell. Make sure the fitting is in a vertical position to pass it through the shell. 11) slide the new drive ...
W w w . S m a r t p o o l . C o m 28 12) reinsert the motor mount screws. 13) reinstall the (2) drive pulleys and tighten the screws using a phillips head screwdriver..
W w w . S m a r t p o o l . C o m 29 14) reinstall the side-plates and tighten the screws using a phillips head screwdriver. (note: the curve of the side-plate should face the pool’s surface or the up direction in this example. The (3) center screws are machine threaded the (2) outside screws are se...
W w w . S m a r t p o o l . C o m 30 replacing the pump motor nc7113.
W w w . S m a r t p o o l . C o m 31 1) remove the impeller cover by unscrewing the (1) mounting screw. 2) remove the (4) motor mount screws. 3) place cleaner upside-down on bench and remove the bottom lid..
W w w . S m a r t p o o l . C o m 32 4) loosen the pressure fitting to the drive motor and gently pull on the wires to expose the connection. 5) carefully remove the heat shrink covering the drive motor connection. 6) loosen the pressure fitting to the cable and gently pull on the wires to expose th...
W w w . S m a r t p o o l . C o m 33 7) carefully remove the heat shrink covering the cable connection. 8) remove the pump motor from the shell. 9) install the new pump motor into the shell; making sure that drive motor and cable connections are on the correct side..
W w w . S m a r t p o o l . C o m 34 10) connect the drive motor clip, feed it into the pump motor and tighten the pressure fitting. 11) connect the cable clip, feed it into the pump motor and tighten the pressure fitting. 12) reinstall the (4) motor mount screws..
W w w . S m a r t p o o l . C o m 35 13) reinstall the impeller cover by replacing the (1) mounting screw..
W w w . S m a r t p o o l . C o m 36 smartpool cleaner evaluation model numbers: nc32au, nc52au.
W w w . S m a r t p o o l . C o m 37 1) place the cleaner on the bench and examine for physical damage and if there is any debris caught in the impeller or drive brush (remove debris if found). 2) remove bottom lid. 3) check filter bag for proper installation. The “push in” sign should be covered by...
W w w . S m a r t p o o l . C o m 38 4) perform a self test: place the unit upside down on the bench, plug in the power supply and the cable. Turn power supply to the on position: the pump motor should run and then the drive motor should turn on. Shut the unit down after the drive motor starts to ru...
W w w . S m a r t p o o l . C o m 39 test the power supply nc1013au and nc1023au.
W w w . S m a r t p o o l . C o m 40 • if power supply is found to be defective, replace with a new power supply and perform another self test. • if power supply is found to be ok, proceed with the following steps. Results 5) test the voltage through the power supply by inserting the prongs of the v...
W w w . S m a r t p o o l . C o m 41 test voltage through cable nc1012:02 (version 2 cable).
W w w . S m a r t p o o l . C o m 42 6) loosen the pressure fitting to the cable and pull on the plug to expose the connection. 7) place the prongs of the voltmeter into the back of the connection (do not disconnect the cable harness) and turn the power supply on to read the voltage through the cabl...
W w w . S m a r t p o o l . C o m 43 test the voltage to the drive motor drive motor nc1006:02 (version 2).
W w w . S m a r t p o o l . C o m 44 8) unscrew pump motor from unit by removing the (4) mounting screws 9) cut the zip tie: this will give easier access to the pump motor. Important: be careful not to cut the wires. 10) pull up on the pump motor to remove it from the shell..
W w w . S m a r t p o o l . C o m 45 11) turn cleaner on its side and place the pump motor on bench (impeller up) 12) loosen the pressure fitting to the drive motor and pull on wire to expose the connection. 13) disconnect the harness and read the voltage off the plug (wire coming from the pump moto...
W w w . S m a r t p o o l . C o m 46 testing sensor wheels.
W w w . S m a r t p o o l . C o m 47 14) loosen the pressure fitting to the sensor wheels, pull on the wires to expose the connection and separate the connection. 15) while reading resistance/checking for continuity, place the prongs of the voltmeter on the two metal contacts on 1 of the 2 sensor wh...
W w w . S m a r t p o o l . C o m 48 replacing the cable nc1012:02 (version 2 cable).
W w w . S m a r t p o o l . C o m 49 1) loosen the pressure fitting to the cable and pull on the plug to expose the connection. Release the connections by separating the harness. 2) turn the red tabs inward to release the cage and gain access to the cable strain relief. 3) remove the (6) screws of t...
W w w . S m a r t p o o l . C o m 50 4) pull the cable through the cleaner shell. Note: the hole alignment of the inner screws (2 holes are offset). 5) insert new cable into shell..
W w w . S m a r t p o o l . C o m 51 6) pull enough cable into the cleaner to reach the pump motor by feeding it around the cable channel. 8) reconnect the cable harness, insert the connection into the pump motor and tighten the pressure fitting. 7) align the holes of the strain relief and the cable...
W w w . S m a r t p o o l . C o m 52 replacing the drive motor nc1006:02 (version 2).
W w w . S m a r t p o o l . C o m 53 1) unscrew the pump motor from the unit by removing the (4) mounting screws. 2) loosen the pressure fitting to the drive motor, pull on wire to expose connection and disconnect the harness. 3) remove the large rubber cap on the drive motor side and remove the (3)...
W w w . S m a r t p o o l . C o m 54 5) feed the new cable through the shell. 6) reconnect the plug, feed the wires into the pump motor and tighten the pressure fitting. 7) feed the motor into the tube, reinstall the (3) screws and replace the rubber cap..
W w w . S m a r t p o o l . C o m 55 8) place the pump motor in the shell and secure it with the (4) motor mount screws. Important: make sure the drive motor cable is around the motor support..
W w w . S m a r t p o o l . C o m 56 replacing the pump motor nc1009:02 or nc1024:02 (version 2).
W w w . S m a r t p o o l . C o m 57 1) unscrew the pump motor from the unit by removing the (4) mounting screws. 2) cut the zip tie: this will give easier access to the pump motor. Important: be careful not to cut the wires. 3) pull up on the pump motor to remove it from the shell..
W w w . S m a r t p o o l . C o m 58 4) turn cleaner on its side and place the pump motor on bench (impeller up) 5) loosen all the pressure fittings and disconnect all the connections. 6) connect all the components to their proper harness, feed wires into the pump motor and tighten pressure fittings...
W w w . S m a r t p o o l . C o m 59 7) place pump motor into shell. 8) place the pump motor in the shell and secure it with the (4) motor mount screws. Important: make sure the drive motor cable is around the motor support..
W w w . S m a r t p o o l . C o m 60 replacing the drive brushes nc1004.
W w w . S m a r t p o o l . C o m 61 1) lift the support tab over the post to remove the brush from the wheel tube. 2) wrap the new brush around the wheel tube and pull the post through the hole in the center of the support tab..
W w w . S m a r t p o o l . C o m 62 replacing the foam ring nc1014.
W w w . S m a r t p o o l . C o m 63 1) remove the large rubber cap on the non-drive motor side and remove the (3) motor mount screws. 2) remove the drive tube mount and slide wheel tube assembly off the drive motor. 3) lift the support tab over the post to remove the brush from the wheel tube. 4) s...
W w w . S m a r t p o o l . C o m 64 5) install the new foam ring and reinstall drive brush. 6) slide the wheel tube onto the drive motor and reinstall the drive tube mount. 7) reinstall the (3) screws and replace the rubber cap..
W w w . S m a r t p o o l . C o m b1 scrubber series cleaners will have the serial number located on the side on the inner shell. The number will ei- ther be printed on the shell or on a sticker. How to locate the serial number scrubber series.
W w w . S m a r t p o o l . C o m b2 wall to wall and wall climbing model cleaners will have the serial number located on either the side or back (behind the cage) of the inner shell. The number will be printed on the shell or on a sticker. How to locate the serial number wall to wall & climber seri...
687 prospect st lakewood, nj 08701 732-‐730-‐9880 installation of cleaner weights 1) remove the protective cover to the adhesive backing. Admiral ultra admiral and admiral plus 2) press the weight on the inside of the shell, ensuring there is enough clearance for the installation of the bottom lid...
Replacing the bottom lid support clips 687 prospect st lakewood, nj 08701 732-730-9880 1) use a cutting tool to cut the tab on the underside of the support. 2) use a flat-head screwdriver to remove the clip from the casing. 3) replace the old clip with the new material provided. Fit the washer onto ...
Replacing the bottom lid support clips 687 prospect st lakewood, nj 08701 732-730-9880 4) place the red clip in the shell of the unit and begin to fasten the screw to the clip. 5) while holding the screw with a phillips-head screwdriver, rotate the red clip until it is firmly in place..
Error reason(s) suggestion(s) dead in water outlet/gfi check outlet/reset the gfi or try another outlet cleaner reset unplug the cleaner and allow it to rest for 30 seconds extension cord try plugging the power supply directly into an outlet not moving debris caught in tracks/brushes/impeller check ...
Covered in this chart nc32au and nc52au test and results chart component working range symptom(s)/result(s) of defective component additional information power supply 28‐32vdc cleaner will be dead in water cable 25‐28vdc cleaner will be dead in water cleaner may go back and forth in one spot pump mo...
In this chart nc71au test and results chart component working range symptom(s)/result(s) of defective component additional information power supply 29‐32 vdc cleaner will be dead in water cable 26‐29 vdc cleaner will be dead in water make sure to test the cable while pump motor is running pump motor...