Doc. No. ＣＵ＊＊－ＯＭ０００２Ｅ－Ａ product name free mount cylinder model/ series Ｃ(d)u series Ｃ(d)uk series Ｃ(d)uw series Ｃ(d)ukw series.
1/10 contents safety instructions 2 1. Specifications 4 2. Installation and handling 6 3. Maintenance 9 4. Basic circuit for cylinder operation 9 5. Troubleshooting 10 s no. ＣＵ＊＊－ＯＭ０００２Ｅ―Ａ.
2/10 free mount cylinder / series cu safety instructions these safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “caution,” “warning” or “danger.” they are all important notes for saf...
3/10 free mount cylinder / series cu safety instructions caution the product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult smc beforehand ...
4/10 φ6 φ10 φ16 φ20 φ25 φ32 rc1/8 double acting d type 0. 0125 single acting t type 0. 0062 0. 025 0. 05 0. 1 0. 2 0. 3 note 1) double-side rubber bumper 0. 0015 0. 02 0. 04 0. 10 0. 15 0. 20 1. Specifications 1-1. Specifications bore size fluid port size max. Operating pressure proof pressure ambie...
5/10 b) double acting double rod type [c(d)u(k)w*-*d] (n 0. 3 0. 5 0. 7 φ6 3 6.36 10.6 14.7 φ10 4 19.8 33 46.2 φ16 6 51.6 86 121 φ20 8 79.2 132 185 φ25 10 124 206 288 φ32 12 207 346 484 pressure receiving area (mm 2 ) 21. 2 66 172 264 412 691 bore size (mm) rod o.D. (mm) operating pressure mpa ) c) ...
6/10 2. Installation and handling ① there is a possibility of dangerous sudden action by air cylinders if sliding parts of machinery are twisted due to external forces, etc. In such cases, injury to personnel may occur; e.G., by catching hands or feet in the machinery, or damage to the machinery its...
7/10 2-4 piping ① use clean air. Do not use compressed air which contains chemicals, synthetic oils containing organic solvents, salts or corrosive gases, etc., as this can cause damage or malfunction. ②install an air filter. Install an air filter upstream near the valve. A filtration degree of 5 mi...
8/10 ① maintenance should be performed according to the procedure indicated in the operating manual. Improper handling can cause damage and malfunction of equipment and machinery. ② machine maintenance, and supply and exhaust of compressed air before components are removed, first confirm that measur...
9/10 3. Maintenance ! Caution as a jig is required for bore size ø6, do not disassemble when replacing seals etc. If overhaul is required, contact smc sales office. Checks 1.Daily check 1)whether the operation is smooth or not. 2)changes in piston speed and cycle time. 3)whether the stroke is approp...
10/10 5.Troubleshooting description possible causes countermeasures note insufficient output the piston seal is worn out. Replace the piston seal. For ø6, request smc to repair. Operating speed is too slow. The load is too much for the cylinder output. ・ increase the bore size of the cylinder. The c...
Revision history 4-14-1, sotokanda, chiyoda-ku, tokyo 101-0021 japan tel: + 81 3 5207 8249 fax: +81 3 5298 5362 url http://www.Smcworld.Com note: specifications are subject to change without prior notice and any obligation on the part of the manufacturer. © 2008 smc corporation all rights reserved n...
