- DL manuals
- SPRT
- Printer
- SP-POS58III
- User Manual
SPRT SP-POS58III User Manual
Summary of SP-POS58III
Page 1
R sprt sp - pos58iii line thermal printer user’s manual beijing spirit technology development co, ltd..
Page 2: Content
Sprt 1 content chapter 1 feature and performance .................................................................................... 2 1.1 print performance ..................................................................................................... 2 1.2 print paper .........................
Page 3
Sprt 2 chapter 1 feature and performance 1.1 print performance ● print method: direct thermal ● print paper width: 57.5±0.5mm ● print density: 8 dots/mm, 384 dots/line ● print speed: approx. 60mm / sec. ● reliability: print head life: 100km using condition: * print 12 × 24 ascii characters, print 50...
Page 4
Sprt 3 ● parallel interface: db25 socket (male), 8-bit parallel interface, supports busy/ack handshaking protocol, ttl signal level. ● ethernet interface: it can work under the full-duplex or half-duplex mode and support ethernet 802.3 protocol, the tcp 、 udp 、 icmp 、 ip 、 arp 、 http printing agreem...
Page 5
Sprt 4 fig.2-1 printer appearance fig.2-2 printer appearance platen upper cover housing paper roll feed button paper out sensor print head sensor indicator power indicator power switch power port case base communication interface cash drawer port.
Page 6
Sprt 5 2.2 paper installation sp-pos58iii adopts 57.5±0.5mm width thermal paper. When there is no paper in the paper case, please don’t press 【 lf 】 button in case effect the reliability of the print head. As fig. 2-3 shows, uplift the handspike according to the arrowhead direction, in order to open...
Page 7
Sprt 6 gnd rts txd rxd dsr dtr gnd cts dcd rxd txd 7 5 3 2 6 4 5 8 1 2 3 gnd rts txd rxd dsr dtr gnd cts dcd rxd txd 7 5 3 2 6 20 7 5 8 3 2 pin no. Signal source description 2 rxd host printer receives data from host 3 txd printer printer transmits data to host 5 cts printer signal “mark” indicates ...
Page 8
Sprt 7 fig.2-7 pin order of parallel port the pin assignment of parallel interface is shown in fig. 2-8 shows: pin no. Signal direction description 1 /stb in strobe pulse to latch data, reading occurs at falling edge. 2 3 4 5 6 7 8 9 data1 data2 data3 data4 data5 data6 data7 data8 in in in in in in ...
Page 9
Sprt 8 14,16,17 nc --- no connection 18-25 gnd --- grounding logical 0 level note: ( 1 ) “in” denotes inputting to the printer , “out” denotes outputting from the printer. ( 2 ) signal level is ttl standard. Fig.2-8 pin assignment of parallel interface 2.3.4 ethernet interface the ethernet interface...
Page 10
Sprt 9 fig.2-9 power socket 2.3.4 power connection sp-pos58iii uses external power supply as 12v, 2a, power socket is a-1009-3p model, as fig. 2-9 shows: 2.4 buttons and indicators power switch: control the power on or off status. Is power off status, “ - ” is power on. Feed button: hold down the bu...
Page 11
Sprt 10 aaa sp-pos58iii offers esc/pos print command sets. Each command is described in following format: print command function format: ascii: the standard ascii character sequence decimal: the decimal numbers sequence hexadecimal: the hexadecimal number sequence explanation: what the command does ...
Page 12
Sprt 11 × × d5 d4 × × × 1: double width print aaa decimal: 27 50 hexadecimal: 1b 32 explanation: set line spacing to 1/6 inch. Esc 3 set line spacing to n dot lines (n/203 inch) format: ascii : esc 3 decimal: 27 51 hexadecimal: 1b 33 explanation: set line spacing to n dot lines. N=0~255. One dot lin...
Page 13
Sprt 12 esc dc4 cancel double width character print format: ascii: esc dc4 decimal: 27 20 hexadecimal: 1b 14 explanation: after carrying out this command, the characters will be printed in normal width. Esc % select/cancel user-defined characters format: ascii: esc % n decimal: 27 37 n hexadecimal: ...
Page 14
Sprt 13 3.2.4 special control commands esc c 5 enable/disable switch button function format: ascii : esc c 5 n decimal: 27 99 53 n hexadecimal: 1b 63 35 n explanation: when n=1, button 【 lf 】 is enabled; when n=0, button 【 feed 】 is disabled; default n=0. 3.2.5 graphics print commands esc * set bit-...
Page 15
Sprt 14 0 8-dot single density 8 68dpi 101dpi 192 1 8-dot double density 8 68dpi 203dpi 384 32 24-dot single density 24 203dpi 101dpi 192 33 24-dot double density 24 203dpi 203dpi 384 gs / print download bit-map graphics format: ascii : gs / n decimal: 29 47 n hexadecimal: 1d 2f n explanation: this ...
Page 16
Sprt 15 gs * define download bit-map graphics format: ascii : gs * n1 n2 [d]k decimal: 29 42 n1 n2 [d]k hexadecimal: 1d 2a n1 n2 [d]k explanation: this command is used to define download bit-map graphics. N1=1 ~ 48 , n2=1 ~ 255 , n1×n2 。 ◆ d is the bit-map data. ◆ the horizontal size of this graphic...
Page 17
Sprt 16 decimal: 29 87 n1 n2 hexadecimal: 1d 57 n1 n2 explanation: n1: bar code narrow bar width, unit: dot. Each dot for sp-pos58iii printer is 1/203 inch or 0.125mm. Default n1=3. N2: bar code broad bar width gs k print bar code format: ascii : gs k n [ d ] nul decimal: 29 107 n [ d ] 0 hexadecima...
Page 18
Sprt 17 gs w set bar code width format: ascii : gs w n decimal: 29 119 n hexadecimal: 1d 77 n explanation: set the width of printing bar code. N = 1 ~ 4. When n is different, the width of bar code will be different, as shows in the following tab: its unit is dot. Each dot for sp-pos58iii is 1/203 in...
Page 19
Sprt 18 esc v transmit status of printer format: ascii : esc v decimal: 27 118 hexadecimal: 1b 76 explanation: send printer status to the host. When printer received the command, it transfers one byte through txd serial interface. Definition of said byte is shown as below: bit function value 0 value...
Page 20
Sprt 19 6 undefined --- --- 7 undefined --- --- appendix 1 index of print commands command name command description print commands lf print and feed line escj print and feed n dot lines line spacing setting commands esc2 set character line spacing to 1/6 inch esc3 set line spacing to n dot lines (n/...
Page 21
Sprt 20 appendix 2 index of print characters.