- DL manuals
- Surveon
- Security Camera
- CAM4220
- User Manual
Surveon CAM4220 User Manual
Summary of CAM4220
Page 1
Cam4220 megapixel ir dome indoor network camera user manual release 1.2 april, 2010
Page 3
Surveon cam4220 all rights reserved © surveon technology 2010 copyright statement no part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic...
Page 4: Table of Contents
Surveon cam4220 table of contents copyright statement.......................................................................... 1 table of contents ............................................................................. 2 chapter 1. Overview .......................................................
Page 5
Surveon cam4220 image appearance.................................................................. 22 video streams....................................................................... 24 audio settings....................................................................... 25 ptz.....................
Page 6: Chapter 1.
Surveon cam4220 chapter 1. Overview 1.1. Network camera introduction the cam4220 is professional ip network camera which uses internet protocol (ip) to transmit video streams and control signals over a network. Capable of operating both lans and wans, this network camera provides a complete budget-c...
Page 7
Surveon cam4220 1.3. Network camera specifications cam4220 image sensor 1/3” 1.3 megapixel progressive scan cmos lens 2.8 - 11 mm varifocal lens, f1.4 viewing angle diagonal: 122°~35° horizontal: 96°~28° vertical: 72°~21° day/night yes ir led yes (30 m) min illumination 0 lux (ir led on) iris contro...
Page 8
Surveon cam4220 alarm out 1, terminal block aux power output 12vdc 400ma video buffer 2 second pre-alarm, 30 second post-alarm event action send snapshot or video clip by ftp or email, record to nas, record to local storage, trigger do supported protocols ipv4, arp, tcp, udp, icmp, dhcp, ntp, ddns, ...
Page 9: System Structure
Surveon cam4220 system structure 1.4. Network camera hardware installation to install the network camera: 1. Locate a suitable spot for installation. 2. Connect the camera to a power source (adapter or poe). 3. Connect the camera to a switch using an ethernet cable. 7 surveon network camera user man...
Page 10: Chapter 2.
Surveon cam4220 chapter 2. Connecting to the camera this section demonstrates how to connect to the network camera through a web browser, streaming media player, or with a mobile device using the 3gpp protocol. 2.1. Connecting with a web browser to connect to the network camera with a web browser: 4...
Page 11: Changing Your Password
Surveon cam4220 changing your password if this is the first time that the network camera is being accessed, the camera will prompt you to change the administrator password after your first login. Click okay 1. Click ok when informed of the need to change your password. This will cause a configure ad...
Page 12
Surveon cam4220 installing active x components you may be prompted to install activex® components when accessing the network camera’s live view page; click “yes” when prompted. You will be able to access the camera after installation is completed. This action may require administrator privileges. If...
Page 13
Surveon cam4220 2.2. Connecting with an rtsp player the cam3260 supports connection through rtsp media players such as real player and quicktime player. 1. Launch real player or quicktime player； 2. Select file -> open url, to open a url dialog box. 3. Enter the camera url in the address bar. Note: ...
Page 14: Chapter 3.
Surveon cam4220 chapter 3. Web interface 3.1. Interface layout this section demonstrates the layout of the network camera’s main interface. The 4 main areas on the interface include: main menu, company logo, main control, and live display window. Control descriptions adjust window size: this feature...
Page 15
Surveon cam4220 play back: turned off by default; goes to the record file management page when clicked. Audio-in: turned off by default; allows audio to be transmitted to the side. Click again to stop audio transmission. Camera note: note: multiple users may access the live view page simultaneously ...
Page 16: 3.2. Settings
Surveon cam4220 3.2. Settings camera settings may be changed by clicking on the settingslink located in the title bar. General general setting menus are found under the general title. Basic settings basic settings may be accessed by clicking the basic settings link under general. Main options includ...
Page 17
Surveon cam4220 user account the user account section mainly controls the account information of the users and their privileges. Available functionality includes add, edit and remove user accounts. The system allows for 2 types of users: administrators and operators. Administrators have full privile...
Page 18
Surveon cam4220 date & time the three main parts of this section include current date & time,time zone settings, and time settings. Current date & time displays the current date and time of the camera. Time zone settings time zone can be set using the dropdown menu (only selectable when synchronizin...
Page 19: Network
Surveon cam4220 network network configuration matically - automatically acquires ip address. If dhcp is ill in ip address, pppoe requires a user name and password from your isp. Ip & dns settings get ip address auto supported and free ip is available, this option allows the camera to automatically a...
Page 20
Surveon cam4220 ddns settings connecting using dynamic dns requires registration on third-party websites for ddns services. Select desired ddns service website, check the “enable ddns” option, and fill in valid user name and password. You can then access the camera through the registered domain name...
Page 21
Surveon cam4220 port settings this section includes http port setting and rtsp settings. Http port settings the port number is used to access the camera. Rtsp settings you may change the access name for stream 1, stream 2, the rtsp port number, the rtp port for video, the rtcp port for video, rtp po...
Page 22
Surveon cam4220 upnp upnp settings as shown in figure 5-6： check the “enable upnp” box and enter a correct friendly name and click “ok”. Once activated, neighboring computers can see the camera and allow direct connection when double clicked. Click ok to save or cancel to abort the changes before yo...
Page 23: Video & Audio Settings
Surveon cam4220 video & audio settings click on “settings” on the top menu to access the settings page; click on “video & audio” to access video & audio settings page. This section includes basic settings, image appearance, video streams, overlay image, and audio. Basic settings basic settings flip ...
Page 24
Surveon cam4220 image appearance image attribution all parameters under image attribution are values ranging from (0) to (100). Brightness - adjusts the brightness of the image; drag the cursor to the right to brighten the image, and vice versa. Saturation - adjusts the saturation of the image; drag...
Page 25
Surveon cam4220 sensor configuration the sensor configuration tabs provide the following options: auto white balance -turns on and off the auto white balance feature. Backlight compensation -turns on and off the backlight compensation feature. Auto gain control -turn on and off to adjust the auto ga...
Page 26
Surveon cam4220 video streams video format - the compression format for the video options include: h.264, mjpeg, mpeg4. Video resolution - sets the resolution of the video output. 4 options are available: sxga, hd720, vga, qvga, qqvga. Video frames per second -sets the number of frames per second. K...
Page 27
Surveon cam4220 when selecting 3gpp mode, the settings for video stream2 is shown below. None of the parameters can be changed. Audio settings elect on to turn on mute or off to turn off mute s page. Mute settings - s codec settings - select adpcm bit rate of 8, 16, 32, 48, or 64 kbp click ok to sav...
Page 28: Ptz
Surveon cam4220 ptz the ptz menu allows configuration of the rs-485 control. Select enable rs-485 control to activate the service. Ptz decoder address - the address (id) of the ptz decorder. Ptz protocol - the protocol used by the ptz (pelco-d or pelco-p). Baud rate - sets the baud rate of the ptz: ...
Page 29: Recording
Surveon cam4220 recording the recording menu deals with recording settings and managing recorded video files. Recording basic settings memory card recording -when memory card recording is turned on, video will automatically be recorded onto the microsd card if the network connection is lost. When a ...
Page 30
Surveon cam4220 recorded file management this section allows users to manage videos recorded on the microsd cards. Download - downloads video files. Select one or more video files and click download; choose location to save the video file(s) onto your local pc. Lock/unlock - locks/unlocks video file...
Page 31
Surveon cam4220 note: the video files shown in record file management are files stored in the microsd card. You can also record live video by clicking the record button in the live view screen. The default path for live video recordings is "c:\documents and settings\" + user+ "\my documents\" + mode...
Page 32: Event Notification
Surveon cam4220 event notification event notification includes the following: event server, motion detection, tampering detection, di&do and event settings. Event server email settings sender email address - email address of the sender of notification emails. Recipient email address - email address ...
Page 33
Surveon cam4220 ftp settings server address - the address of the ftp server. Server port - the port number of the ftp server; default is 21. User name - the user name of the ftp account. Password - the password of the ftp account. Ftp folder name - the name of the folder on the ftp site which video ...
Page 34
Surveon cam4220 motion detection motion detection is activated by checking the enable motion detection box. The video displaying on the event notification settings window is the live streaming video. The active curve chart is displayed in the active status display tab under basic settings. Setup for...
Page 35
Surveon cam4220 the windows settings interface is as follows: a maximum of 3 motion detection windows can be added in windows settings page by clicking new. Enter the following parameters: window name - the name of the motion detection window. Trigger interval - the time interval between motion trig...
Page 36
Surveon cam4220 tampering detection the tempering detection parameters include: tampering detection - turns on or off tampering detection. Trigger threshold - sets the trigger threshold of tampering detection; ranges from 0 to 100. Sensitivity - sets the sensitivity of tampering detection; ranges fr...
Page 37
Surveon cam4220 di & do the back panel of the camera contains the following: 1 do out port 2 di in ports +12v power port ground di/do is used as part of event triggering. Do - when motion/event/tampering is detected or when scheduled events occur, do can send out high or low voltage to trigger exter...
Page 38
Surveon cam4220 input 1 and input 2 correspond to di1 and di2 outputs, with the following 3 conditions: normal open: di requires a low voltage input, with the following configuration normal close: di requires a high voltage input, with the following configuration off: di inputs are closed at all tim...
Page 39
Surveon cam4220 event settings event settings include event list and schedule list. By clicking add under event list or schedule list you can add new conditions for event triggering. Choosing an event and clicking edit will allow you to edit the conditions, while clicking remove will delete the even...
Page 40
Surveon cam4220 general name - specifies the name of the event. Minimum time interval between triggers - (event list only) the time frame in which a subsequent trigger of the same event will be ignored (maximum 23:59:59). Set time interval - (scheduled list only) the time when this event will be tri...
Page 41
Surveon cam4220 when triggered this section specifies the actions to take when conditions in triggered by are met; options are: email - emails notifications to specified email address. If this is chosen, fill in the following subject - the subject line of the email. Additional information - the cont...
Page 42: System
Surveon cam4220 system microsd card management basic settings basic settings shows the status of the current microsd card. Enter the administrator password and click format to format the microsd card. Microsd card management microsd card management calculates how much time for recording. Users may a...
Page 43
Surveon cam4220 system status this section displays the status of the system, including ip address, mac address, subnet mask, default router, microsd card capacity status, boot loader and firmware versions. Clicking on email will send the system status information out as an email. 41 surveon network...
Page 44
Surveon cam4220 system log this section provides a log for all system-related entries. The log lists all visiting information, as well as changes to camera settings (both successful and unsuccessful). The information is very useful, as it provides all traces of any access to the system and the camer...
Page 45
Surveon cam4220 firmware upgrade there are 2 ways to upgrade the firmware: upgrading through firmware stored locally on a pc upgrading through firmware stored in a microsd card if upgrading through firmware stored locally, enter the path of the file in the provided field or click browse to find the ...
Page 46
Surveon cam4220 reset to factory default there are 2 types of reset. You can either reset all settings and configurations, or you can choose to keep the network configuration, and reset all other settings and configurations. Click ok after choosing a reset option to perform a reset. Alternately, you...
Page 47
Surveon cam4220 export/import & reboot this section allows you to restart the camera, as well as export and import camera configuration details. Restart the network camera - reset the camera settings by clicking apply. Export configuration - export the camera’s settings and configurations by clickin...