Printed in u.S.A. 8-06 © copyright 2006 tac all rights reserved. F-23837-5 tac 1354 clifford avenue p. O. Box 2940 loves park, il 61132-2940 www.Tac.Com application these sensors provide electronic sensing of room temperature at wall locations for use with microprocessor-based energy management syst...
2 © copyright 2006 tac all rights reserved. F-23837-5 specifications sensor inputs connections: coded screw terminals. Environment ambient temperature limits: shipping, -40 to 160°f (-40 to 71°c). Operating, 40 to 140°f (4 to 60°c). Humidity: 5 to 95% rh, non-condensing. Locations: nema type 1. Opti...
F-23837-5 © copyright 2006 tac all rights reserved. 3 table-1 specifications. Table-2 temperature vs. Resistance. Typical application part number cover thermometer cover dimensions h x w x d in. (mm) temperature sensing element range display description brand name resistance maximum error over 100°f...
4 © copyright 2006 tac all rights reserved. F-23837-5 installation inspection inspect the package for damage. If damaged, notify the appropriate carrier immediately. If undamaged, open the package and inspect the device for obvious damage. Return damaged products. Requirements • job wiring diagrams ...
F-23837-5 © copyright 2006 tac all rights reserved. 5 mounting dimensions figure-2 dimensions for mounting ts-5711-770 and ts-5711-850 series on american standard 2" x 4" electrical box. 1-7/16 (37) depth = 1-5/8 (43) dimensions shown are in inches (mm). 1-5/8 (43) 4-7/16 (113) 3-9/32 (83) centered ...
6 © copyright 2006 tac all rights reserved. F-23837-5 mounting ts-5711-770 and ts-5711-850 sensor on american standard 2" x 4" electrical box 1. Remove the cover screw and remove the sensor cover from the base plate (see figure- 6 ). 2. Identify the two wires that are to be connected to the sensor. ...
F-23837-5 © copyright 2006 tac all rights reserved. 7 mounting ts-57011-770 or ts-57011-850 series sensor on american standard 2" x 4" electrical box 1. Remove the sensor cover from the base plate, according to the following: a. Insert the blade of a small-bladed screwdriver into the cover latch slo...
8 © copyright 2006 tac all rights reserved. F-23837-5 6. Connect the wires to the terminal block on the base plate. See the wiring diagrams in figure-1 . When installing a wire in the terminal block, insert the wire from the top side of the terminal and secure it by tightening the screw located on t...
F-23837-5 © copyright 2006 tac all rights reserved. 9 mounting ts-57011-770 or ts-57011-850 series sensor on european 1/4 din standard electrical box 1. Remove the sensor cover from the base plate, according to the following: a. Insert the blade of a small-bladed screwdriver into the cover latch slo...
10 © copyright 2006 tac all rights reserved. F-23837-5 5. Using two appropriately sized mounting screws (not provided), mount the base plate onto the 1/4 din electrical box. Note: no more than 6" (152 mm) of wire should remain under the cover. 6. Strip 1/4" (6 mm) of insulation from the ends of the ...
F-23837-5 © copyright 2006 tac all rights reserved. 11 mullion mounting ts-57031 and ts-57031-850 1. Using a 0.062" allen wrench (tool number n2-4), turn the cover set screw clockwise into the base plate, to release the sensor cover. Remove the sensor cover. Refer to figure- 11 . Note: the sensor is...
Copyright 2006, tac all brand names, trademarks and registered trademarks are the property of their respective owners. Information contained within this document is subject to change without notice. F-23837-5 www.Tac.Com tac 1354 clifford avenue p.O. Box 2940 loves park, il 61132-2940 wiring caution...