TAG Heuer HL 200 User Manual - page 4
4
Control Codes and Escape Sequences
Function
Code
Decimal
Hex
Function
Code
Decimal
Hex
Horizontal tab
HT
9
09
Country select
ESC R n
27 82 n
1B 52 n
Line feed
LF
10
0A
Double width on
ESC W 1
27 87 1
1B 57 01
Form feed
FF
12
0C
Double width off
ESC W 0
27 87 0
1B 57 00
Carriage return
CR
13
0D
Compress bit image graphics
ESC n[d1]… n24[d24]
27 90 n1 … n24
1B 5A n1 … n24
Double width on
SO
14
0
E
Print & feed paper
ESC d n
27 100 n
1B 64 n
Double width off
SI
15
0F
Lable advance
ESC f
27 102
1B 66
Cancel
CAN
24
18
Reversed on
ESC i 1
27 105 1
1B 69 01
Set print mode
ESC ! n
27 33 n
1B 21 n
Reversed off
ESC I 0
27 105 0
1B 69 00
Set barcode start position
ESC $ n1 n2
27 36 n1 n2
1B 24 n1 n2
Double height on
ESC w 1
27 119 1
1B 77 01
Set bit image (8 pin single density)
ESC * 0 n1 n2 [d]
27 42 0 n1 n2 [d]
1B 2A 00 n1 n2 [d]
Double height off
ESC w 0
27 119 0
1B 77 00
Set bit image (8 pin single density)
ESC * 1 n1 n2 [d]
27 42 1 n1 n2 [d]
1B 2A n1 n2 [d]
Inverse on
ESC { 1
27 123 1
2B 7B 00
Set bit image (24 pin single density)
ESC * 32 n1 n2 [d]
27 42 32 n1 n2 [d]
1B 1A 20 n1 n2 [d]
Inverse off
ESC { 0
27 123 0
1B 7B 00
Set bit image (24 pin single density)
ESC + 33 n1 n2 [d]
27 42 33 n1 n2 [d]
1B 1A 21 n1 n2 [d]
Set barcode height (1 GS h n 29 104 n 1D 68 n Underline on ESC – 1 27 45 1 1B 2D 01 Print UPC-A barcode GS k 0 [d] NULL 27 107 0 [d] 0 1D 6B 00 [D] 00 Underline off ESC -0 27 45 0 1B 2D 00 Print UCP-E barcode GS k 1 [d] NULL 27 107 1 [d] 0 1D 6B 01 [D] 00 Reset ESC @ 27 64 1B 40 Print EAN13 barcode GS k 2 [d] NULL 27 107 2 [d] 0 1D 6B 02 [D] 00 Set page length ESC C n 27 67 n 1B 43 n Print EAN8 barcode GS k 3 [d] NULL 27 107 3 [d] 0 1D 6B 03 [D] 00 Set horizontal length ESC D n 27 68 n 1B 44 n Print Code 39 barcode GS k 4 [d] NULL 27 107 4 [d] 0 1D 6B 04 [D] 00 Bold on ESC G 27 71 1B 47 Print 2 of 5 barcode GS k 5 [d] NULL 27 107 5 [d] 0 1D 6B 05 [D] 00 Bold off ESC H 27 72 1B 48 Print codabar barcode GS k 6 [d] NULL 27 107 6 [d] 0 1D 6B 06 [D] 00 Set bit image ESC K n1 n2 [d] 27 75 n1 n2 [d] 1B 4B n1 n2 [d] Print CODE 128 barecode GS k 7 n [d] 27 107 7 n [d] 1D 6B 07 [D] 00 Set barecode magnification 2 GS w n 29 119 n 1D 77 n Print Mode (ESC !) Value Bit Function 0 1 0 Print Density Bit 3 Bit 2 Character Font Bit 1 Bit 0 1 Character font (see below) Light 1 (Default) 0 0 24 characters per line 0 0 2 2 0 1 48 characters per line 0 1 3 Print density (see below) 3 (Label Default) 1 0 32 characters per line 1 0 4 Double height Cancelled Set Dark 4 1 1 Undefined 1 1 5 Double width Cancelled Set 6 Undefined 7 Undefined Cancelled Set Replacing Paper Roll If the paper roll needs replacing, open the paper cup lid (squeeze cup lid as shown in Fig 3) and remove the remaining paper using the Paper Feed button, do not pull paper through the printer mechanism. Reel off a few centimetres from a new roll of paper and check that the end has a clean straight edge (see Fig 4). Slide the leading edge of the paper through the paper entry slot, with the leading edge of the paper feeding forwards from the bottom of the roll, until you feel resistance. Press the paper feed button and feed the paper through the printer mechanism (see Fig 5). Keep the paper feed button depressed until enough paper is fed through the printer mechanism to pass through the paper exit slot. Sit the new paper roll in the paper cup and close the lid. Should the paper become creased or out of line when feeding in a new roll, cut the end off the paper roll, feed out the creased paper using the Paper Feed button, and reload ensuring the paper has a clean straight edge. TAG Heuer PROFESSIONAL TIMING 6A Louis-Joseph Chevrolet 2300 la Chaux-de-Fonds Switzerland Tel : 032 919 8000 Fax : 032 919 9026 info@tagheuer-timing.com www.tagheuer-timing.com