Hedge trimmer model tht- 210b/sa/2000/sa/sla/ 2100/sa/240b/2510s/ 2520sa/2530/2540 htd- 2520pfa/2522pfa/ 2526pfa/2530pfa hts-2530pf handling instructions note: before using this machine, carefully read through these handling instructions to ensure e ffi cient, safe operation. It is recommended that th...
Meanings of symbols note: some units do not carry them symbols warning the following show symbols used for the machine. Be sure that you understand their meaning before use. It is important that you read, fully understand and observe the following safety precautions and warnings. Careless or imprope...
What is what? Since this manual covers several models, there may be some di ff erence between these illustrations and your unit. Use the instructions that apply to your unit. 1. Recoil starter 2. Fuel tank 3. Throttle trigger lookout 4. Throttle trigger 5. Front handle 6. Rear handle 7. Spark plug 8....
Warnings and safety instructions operator safety ○ always wear a safety face shield or goggles. ○ always wear heavy, long pants, boots and gloves. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair so it is above shoulder length. ○ do not operate this tool when you...
Specifications model tht - 210b / sa tht - 2100 / sa / 2000 / sa / sla tht - 2520sa tht - 240b engine size (ml) 22 24 22 spark plug ngk bpm-6a or bpmr-6a champion rcj-8y ngk bpm-6a or bpmr-6a champion rcj-8y ngk bpm-6a or bpmr-6a champion rcj-8y fuel tank capacity (l) 0.35 0.35 0.35 dry weight (kg) ...
Model tht - 2510s tht - 2530 / 2540 htd - 2520pfa / 2522pfa htd - 2526pfa / 2530pfa hts - 2530pf engine size (ml) 24 24 24 spark plug ngk bpm-6a or bpmr-6a champion rcj-8y ngk bpm-6a or bpmr-6a champion rcj-8y ngk bpm-6a or bpmr-6a champion rcj-8y fuel tank capacity (l) 0.35 0.33 0.33 dry weight (kg...
Assembly procedures handle b (3) and gathering plate (4) (fig. 1) 1. Remove the four washers and nuts (1) from cutting blade end. Note in case of handle b installation only, remove only the nut on the longest bolt. 2. Set the gathering plate on the cutter guide, then fi nger tighten the three washer...
Fig. 6 2. With the safety lever (8) pressed, pull throttle trigger and push lock button (9) (if so equipped), then slowly release throttle the trigger fi rst, then the safety lever. This will lock the throttle in starting position. ( fig. 4, 5 ) 3. Set choke lever (11) to closed position (b). ( fig....
Maintenance maintenance, replacement or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. Carburetor adjustment (fig. 13) warning ○ the cutting attachment may be spinning during carburetor adjustments. ○ never start the engin...
When clearance is too small the cutters do not move properly and the sliding surfaces may seize. When clearance is too large the cutters are poor in sharpness. To adjust the cutter clearance 1. Loosen the cutter fi xing nuts. 2. Fully tighten the cutter fi xing bolts and then loosen them approx. 1/2...
11 000book̲tht-210b̲eng.Indb 11 000book̲tht-210b̲eng.Indb 11 2009/08/18 8:52:25 2009/08/18 8:52:25.
908 code no. E99004211 g printed in china 000book̲tht-210b̲eng.Indb 12 000book̲tht-210b̲eng.Indb 12 2009/08/18 8:52:25 2009/08/18 8:52:25.
